Pentair HYPRO 9305C Series User manual

KEEP FOR FUTURE REFERENCE
pentair.com
INSTALLATION AND
OPERATION MANUAL
CAST IRON SERIES CENTRIFUGAL PUMPS
9305C 9305C-SP
L-1595 Rev. B (12-09-19) Pentair 375 5th Ave. NW, New Brighton, MN 55112 Phone: [phone] -OR- 800-424-9776 Fax: [phone] www.pentair.com
EC REP
EU Authorized Representative:
QNET BV Hommerterweg 286 6436 AM Amstenrade, The Netherlands KvK Zuid-Limburg 14091511

2
Form L-1595
Rev. B
12-09-19
Contents
EU Languages.........................................................................................................................................................................3
Introduction.................................................................................................................................................................4
Description.....................................................................................................................................................4
Intended Uses............................................................................................................................................................4
Purpose of Manual....................................................................................................................................................4
Misuses...........................................................................................................................................................4
 Pump Identication....................................................................................................................................................5
 PumpTechnicalData.................................................................................................................................................5
Fluid PumpingApplications.........................................................................................................................................7
Tools................................................................................................................................................................7
Lifting, Transport, and Intermediate Storage...............................................................................................................7
Assembly and Installation........................................................................................................................................................8
Assembly.........................................................................................................................................8
Installation......................................................................................................................................8
Plumbing Diagram.....................................................................................................................................................9
Control Systems .....................................................................................................................................................10
Commissioning, Start-Up, Operation, Shutdown...................................................................................................................10
Information.....................................................................................................................................10
Start-Up, Operation, Shutdown................................................................................................................................11
Maintenance and Servicing..................................................................................................................................................12
Information............................................................................................................................12
Disposal.................................................................................................................12
Cleaning............................................................................................................................13
Maintenance, Routine Servicing, and Inspection.....................................................................................................13
Troubleshooting.................................................................................................................................13
Replacement Parts...................................................................................................................................................14
ECDeclarationofIncorporation.............................................................................................................................................15
Warranty. ..................................................................................................................................................................Last page

3
Form L-1595
Rev. B
12-09-19
EU Languages
DO NOT attempt to install or operate your pump before reading the manual. Original copies of the manual for Hypro
pumpsareprovidedinEnglish.Tondacopyinyournativelanguage,gotowww.hypro.pentair.com.
Vor dem Ablesen des Handbuches versuchen Sie NICHT, Ihre Pumpe zu installieren. Originale des Handbuches fur
Hypro-PumpenwerdenaufenglischzurVerfugunggestellt.ZueineKopieinIhrerMuttersprachenden,zu
www.hypro.pentair.com zu gehen (German)
N’essayez pas d’installer votre pompe avant de lire le manuel. Des exemplaires originaux du manuel pour des pompes
de Hypro sont fournis en anglais. Pour trouver une copie dans votre langue maternelle pour aller a
www.hypro.pentair.com (French)
NON tentare di installare la vostra pompa prima di leggere il manuale. Esemplare originale del manuale per Hypro
pompe sono in inglese. Per trovare una copia nella vostra lingua andare a www.hypro.pentair.com (Italian)
Непытайтесьустановитьвашнасосдочтенияруководства.Оригинальныекопииэтогоруководствадлянасосы
Hyproнаанглийскомязыке.Найтикопиюнавашроднойязыкперейтикwww.hypro.pentair.com(Russian)
NO intente instalar su bomba antes de leer el manual. Copias originales del manual para Hypro se provee de bombas
en ingles. Para encontrar una copia en tu idioma nativo ir a www.hypro.pentair.com (Spanish)
NIEprobowaćinstalowaćpompyprzedjejodczytanieminstrukcji.OryginalnekopieinstrukcjiobsługipompHyprosą
dostarczanewjęzykuangielskim.Abyuzyskaćkopięwtwoimojczystymjęzykuprzejdźdowww.hypro.pentair.com
(Polish)
Takmayacalışmayınokumadanoncepompanınmanuel.OrijinalkopyalarınıHypropompalarıicinIngilizceolarak
sunulmuştur.Birkopyasınıbulmakicinyereldilgitwww.hypro.pentair.com(Turkish)
Nao tente instalar a bomba antes de ler o manual. As copias originais dos manuais para Hypro bombas sao
fornecidos em Ingles. Para encontrar uma copia em sua lingua nativa ir para www.hypro.pentair.com (Portuguese)
VERGEETNIETuwpompvoorhetlezenvanhethandboek.ExemplarenvandehandleidingvoorHypropompenzijn
beschikbaarinhetEngels.Opzoeknaareenexemplaarinuweigentaalganaarwww.hypro.pentair.com(Dutch)

4
Form L-1595
Rev. B
12-09-19
Introduction
Description
Hyprocentrifugalpumpsaredesignedforcreatingandboostingpressureinuidcircuits.Thepumpoperatesbytaking
inuidfromtheinletportafterwhichitisslungbytheimpellerandexpelledthroughtheoutletport.Constructionfeatures
include housings, impellers and seals which come in a variety of materials in order to be resistant to a range of chemicals.
Standardmodelsofcentrifugalpumpsrotateclockwise,whenlookingatthefront(Voluteend)ofthepump.
Intended Uses
Hyprocentrifugalpumpsareintendedforcreatingorboostingdynamicpressureinapproveduids.Hyprocentrifugal
pumps should never be used to pump liquids above 140°F (60°C), or below 34°F (1°C). For pumps equipped with
hydraulic motors, the pump should not be run if the hydraulic oil temperature exceeds 160°F (71°C). Any uses outside
ofthosespeciedinthismanualareconsideredmisusesandareprohibited.ContactHyprotechnicalservicewithany
questionsregardingspecicacceptableuses.
Purpose of Manual
This manual provides instructions and requirements that must be met when installing, using and maintaining the
product(s)identiedonthecover.
If the product is sold, the seller must pass this manual onto the new owner.
The following special attention notices are used to notify and advise the user of this product of procedures that may be
dangerous to the user or result in damage to the product.
ATTENTION
Attention is used to notify of installation, operation, or maintenance information that is important but not safety related.
Thissymbolisusedtodenotethepresenceofanelectricalhazardthatwillresultinpersonalinjury,deathorproperty
damage.
Thissymbolisusedtodenotethepresenceofahazardthatwillresultinpersonalinjury,deathorpropertydamage.
California Proposition 65 Warning --Thisproductandrelatedaccessoriescontainchemicalsknowntothe
State of California to cause cancer, birth defects or other reproductive harm.
Misuses
Hyprocentrifugalpumpsaredesignedtooperateeffectivelywithinthespeciedspeed,pressureandenvironmental
ranges.Goingoutsideoftheserangeswillvoidthewarrantyandcouldcausedamagetoproperty,seriousinjury,ordeath.
• DO NOTrunthepumpfasterthanthemaximumspeciedspeed.
• DO NOTrunthepumphigherthanthemaximumspeciedpressure.
• DO NOT run pumps when the liquid has exceeded the maximum or minimum temperature limit (see Intended Uses).
• DO NOT pump non-approved liquids.
• DO NOT pump water or other liquids for human consumption.
• DO NOToperateanyHypropumpundertheinuenceofdrugsoralcohol.
• DO NOT run the pump dry.
• DO NOTrunthepumphydraulicmotorhigherthanthespeciedRPM,pressureorow.
• DO NOT use pumps in an explosive environment.
• DO NOTattachapipe,hoseorttingtothepumpthatisnotratedforthemaximumpressureofthepump(outlet)or
vacuum of the pump (inlet).
• DO NOT run the pump in reverse of its intended rotation.
• DO NOT operate a pump with a gasoline engine in an enclosed area.
• DO NOT run the pump with a higher than recommended voltage.

5     
Form L-1595
Rev. B
12-09-19
Pump Identication
Hypro uses serialized labeling to enable users to precisely identify the pump’s manufacturing date.
Serial Number:
First and second digits: year (14 = 2014)
Third through fth digits: consecutive day of the year the pump was manufactured.
Sixth through tenth digits: unique pump serial number.
Pump Technical Data
(Allspecicationsandperformancedataarebasedonwaterasacarrieruid.)
9305C-HM3C
A
E
D
B
C
G
F
H
I
A
E
D
B
C
G
F
H
I
9305C-HM3C-SP & 9305C-HM3C-BSP
Pump Dimensions
Dim. Inch mm
A 12.44 316.0
B 12.00 304.8
C 6.00 152.4
D 5.81 147.6
E 4.52 114.8
F 11.85 301.0
G 4.91 124.7
H 5.25 133.4
I 2.63 66.8
Pump Dimensions
Dim. Inch mm
A 15.75 400.1
B 12.09 307.1
C 6.04 153.4
D 12.60 320.0
E 1.76 44.7
F 13.60 345.4
G 6.65 168.9
H 5.25 133.4
I 2.63 66.8
E
D
C
B
A
H
I
F
G

6
Form L-1595
Rev. B
12-09-19
Pump Technical Data
Pump
Hydraulic
Motor Inlet
Max PSI
[BAR]
Hydraulic
Motor
Outlet
Max PSI
[BAR]
Max
Hydraulic
Flow
Rate GPM
[LPM]
Max Flow
Rate GPM
[LPM]
Max Pump
Pressure
PSI [BAR]
Pump Ports Hydraulic
Ports
Dry
Weight
lb[kg]
Mounting
Bolts
9305C-HM3C
3000 [207] 100 [6.9] 19 [72]
190 [719] 160 [11.0] 2” NPT Inlet 1-1/2”
NPT Outlet
1/2” NPT
Inlet 3/4”
NPT
Outlet
SAE-4
Case
Drain (If
equipped)
54[24.5]
2X 3/8” OR
M10
9305C-
HM3C-SP 155 [587] 143 [9.9]
2 “ NPT Inlet 2”
NPT Outlet 59[26.8 ]
9305C-
HM3C-BSP
2” BSPP Inlet 2”
BSPP Outlet

7
Form L-1595
Rev. B
12-09-19
Fluid Pumping Applications
Application
Pump Materials Compatibility
Impeller Pump Housing Seal
Nylon Cast Iron Ceramic Silicon
Carbide
Weed Control Chemicals X X X X
Insect Control X X X X
BrushControl X X X X
Pest Control Chemicals
and Fumigants X X X X
Liquid Fertilizers X X X
Powdered Fertilizers X X X X
Fluid Transfer X X X X
Acids X
Table 1
Flammable liquids, sewage, and clean water should never be pumped through a Hypro pump.
Hypropumpsarenotdesignedtobeusedascleanwaterpumpsasdenedin10CFRParts429and431.
Tools
The Hypro centrifugal pumps and mounting assemblies are designed with Imperial (inch) bolts. However, there are many
metric(mm)sizeswhichwillworkwiththesemounts.Inmostcases,anadjustablespannerwrenchcanalsobeused.
Lifting, Transport, and Intermediate Storage
Packaging Descriptions and Unpacking Instructions
• Hypro centrifugal pumps are shipped in cardboard boxes for safe transporting.
• When pumps are shipped in large quantities, they may be put on a pallet to allow for easy storage, lifting and
handling.
• Beforeliftinganypumporpallet,determinetheweightoftheitembylookingattheattachedpackingslipstoestablish
what lifting equipment should be used.
• Beforeinstallingthepump,determineifallthecomponentsarepresentandundamaged.Ifthepumpismissing
components, contact customer service immediately.
• Oncethepumpisunpacked,disposeofthepackaginginamannercompliantwithlocalandnationalregulations.
Lifting Instructions
• BeforeattemptingtoliftaHypropump,ensurethatthesurroundingworkingareaisfreeofhazardswhichcouldcause
injuryordamagetoproperty.
• Duringliftingoperations,anypersonnelnotinvolvedintheliftshouldnotentertheworkingarea.
• Ifliftinghooks,ropeorchainsarebeingusedforalift,theymustbefreeofdamageandberatedtocarry150%ofthe
weight of the load to be lifted.
• Always wear steel-toed shoes and cut-resistant gloves when attempting to lift.
• Whenliftingandcarrying,alwayskeepthepumpclosetoyourbody.(SeeFigure1)
• Whenstartingthelift,bendyourkneesandkeepyourbackstraight.(SeeFigure1)Tighteningthestomachmuscles
willhelpkeepyourbackstraight.
• Duringthelift,useyourlegstodothework.Neveruseyourback,andmakesureyourlegsareatleastshoulder-width
apart. (See Figure 1)
Pump
Hydraulic
Motor Inlet
Max PSI
[BAR]
Hydraulic
Motor
Outlet
Max PSI
[BAR]
Max
Hydraulic
Flow
Rate GPM
[LPM]
Max Flow
Rate GPM
[LPM]
Max Pump
Pressure
PSI [BAR]
Pump Ports Hydraulic
Ports
Dry
Weight
lb[kg]
Mounting
Bolts
9305C-HM3C
3000 [207] 100 [6.9] 19 [72]
190 [719] 160 [11.0] 2” NPT Inlet 1-1/2”
NPT Outlet
1/2” NPT
Inlet 3/4”
NPT
Outlet
SAE-4
Case
Drain (If
equipped)
54[24.5]
2X 3/8” OR
M10
9305C-
HM3C-SP 155 [587] 143 [9.9]
2 “ NPT Inlet 2”
NPT Outlet 59[26.8 ]
9305C-
HM3C-BSP
2” BSPP Inlet 2”
BSPP Outlet

8
Form L-1595
Rev. B
12-09-19
Figure 1
Transport
• All Hypro pumps are capable of being transported by air, sea, rail or motor vehicle. When the pump is shipped, ensure
that the pump is moved in accordance with local and national laws and is properly secured to prevent unwanted
movementwhichcouldcausedamagetopersonorproperty.Priortoshipping,alluidsshouldberemovedfromthe
pump.
Storage
• New pumps in their boxes can be stored several years as long as the port plugs are not removed. Once the plugs
have been removed, if the pump is not to be used for an extended period of time (i.e. more than 30 days), the pump
must be winterized as described in the Cleaning section of this manual.
Assembly and Installation
Assembly
• This pump comes completely assembled.
Installation
BeforeattemptingtoinstallyourHyprocentrifugalpumpitisimperativetoreadandunderstandthefollowing:
• InstallationofaHypropumpshouldonlybeperformedbyatechnicianhavingtheknowledgeandskillsnecessary
toinstallthepumpwithouttheriskofpropertydamageorinjury.
• When handling Hypro pumps, one should wear steel-toed shoes and protective gloves in order to protect the feet
in the event the pump is dropped and protect the hands from any sharp surfaces on the pump or chemicals.
• Pumping systems must be installed in accordance with Hypro installation instructions. Failure to do so will void
yourwarrantyandcouldcausedamagetoproperty,seriouspersonalinjury,ordeath.
• Electricalpowercablesandpumphosesmustberoutedwherethereisnoriskofpersonneltripping,walkinginto,
or falling because they have been routed in areas where personnel are expected to move. Electrical power cables and
pump hoses should be routed according to local and national standards.
• Itistheinstaller’sresponsibilitytoensurethatACelectric-drivemotors,Hypropumps,andmetalworkofsupport
structures are bonded to earth (ground), per local and national standards.
• It is the installer’s responsibility to conduct earth continuity tests between AC electric-drive motors, Hypro pumps,
andmetalworkofsupportstructuresandearthaccordingtoEN60204-1:2006/A1:2009,oritssupersedingstandard,to
conrmthatallcomponentsthatneedtobeconnectedtoeartharesatisfactorilybonded.
• Itistheinstaller’sresponsibilitytoconductelectricaltestsinaccordancewithEN60204-1:2006/A1:2009,orits
supersedingstandard,onnishedpumpassemblies.
• All connections to electrical components must be number, symbol, or color-coded generally as recommended by
EN60204-1:2006/A1:2009,oritssupersedingstandard.
• Installers must provide hydraulic components that are capable of withstanding maximum source pressure.
• Theworkingpressuremustbecontrolledbyapressurereliefvalvethatisadjustedtooperateatamaximum
pressure of the hydraulic motor.

9
Form L-1595
Rev. B
12-09-19
Ref.
No. Description
1TankLid
2 Vent Line
3Jet Agitator
4Shut-offBallValves
5Centrifugal Pump
6 Spray Control Console
7 Centrifugal Pump Control
8ManifoldBoomValve
9 Flowmeter
10 JetTurretNozzleBody
Hydraulic Installation
• Prior to installation, refer to the tractor or sprayer manual and determine what type of hydraulic system is being used.
Thethreetypesofsystemsinclude:
• Open center systems
• Closed center (Pressure-Compensated) systems
• Closed center Load Sensing (Flow and Pressure-Compensated) systems
•Thehydraulicmotormustbecorrectlyconguredandsizedforthehydraulicsystem:
• Open center systems
• Excess oil from the hydraulic pump must be bypassed around the motor
   •Builtinbypassoptioninmotorendplate,orseparatebypassvalveinstalledinthe
line feeding the motor inlet.
• Use the largest motor possible
• If a rigid plumbing system is to be used on a Hypro centrifugal pump, the system must be properly aligned with
the inlet and outlet ports.
• For pumps with gas engines, the exhaust must be directed away from operators and anyone standing nearby to
ensure that exhaust fumes do not enter their breathing zone.
• Theworkingpressureinthehydraulicssystemmustbecontrolledbyapressurereliefvalvethatisadjustedto
operateat10%ofthemaximumsystempressure.
• Wheninstalling,adjustingorremovingaHyprocentrifugalpump,ensurethattherearenoobjectswhichcanfall
ontheinstallerandmakecertainthatallmachinerytowhichthepumpistobeattachedisturnedoff.
• Pumps must be installed in a location where they are accessible for any necessary maintenance.
• Whenhydraulicpowerisused,thesystemshouldcontainaquickdisconnectcouplingthatcanbedisconnected
to isolate the pump.
• When a main electrical supply is needed to power electric-drive motors, installers are responsible for ensuring that
a supply disconnect device, capable of isolating the machine from its electricity supply, be provided.
Standard Mounting
• Inordertopreventinjuryordamagetoproperty,allHypropumpsshouldbeproperlymountedtoasolidbasewhere
thereisnodangerofthepumpfallingorbreakingloose.AllHypropumpscomewithmountingholeswhichallow
bolts to be put into the pump so it can be secured to a sturdy base. When mounting your Hypro centrifugal pump, be
sure to use bolts and nuts which are compatible with any chemicals that may come into contact with them as well as
choosing the correct grade of bolt based on the pump weight and any expected loads. Pumps should be mounted
as close to the liquid source as possible. Non self-priming pumps must be mounted below the liquid level to function
properly.
Pump Plumbing
• To achieve maximum pump performance, the outlet port on the pump should be pointing straight up, and pump
inlet and outlet lines should be at least the same size as their respective port. Pump plumbing must be capable of
withstanding the maximum suction, and pressure, generated by the pump and should have as few restrictions as
possible.
• For best priming results, the upper most vent plug can be removed and a vent line can be installed. This line prevents
airlockandallowsthepumptoprimeitselfbybleedingofftrappedair. Avoid any dips or bends in the suction line
plumbing that could trap air.

10
Form L-1595
Rev. B
12-09-19
Control Systems
• All pump systems with electric or hydraulic power sources are required to have a control system which meets all local
and national standards.
• For more detail on a typical system installation, see preceding subsections of the “Assembly and Installation” section
of this manual.
• Closed center (Pressure-Compensated) systems
  •Meteringoricesneededforoptimalperformance
• Use the smallest motor possible
• Closed center Load Sensing (Flow and Pressure-Compensated) systems
  •Nospecialrequirementforbypassormeteringorices
Hydraulic system plumbing
• Wheninstallingthehydraulicmotorintothetractororsprayer’shydraulicsystem,makesurethatnodirtorliquidgets
into the hydraulic motor.
KEEP ALL HYDRAULIC CONNECTIONS CLEAN.
• Ensure return line is connected to low pressure return port on the tractor recommended for hydraulic motors, the ports
areidentiedonthemotorcasting.Hydraulicsupplylinesshouldbeatleastthesamesizeasthehydraulicmotorport
or larger.
• Standardmodelscomeequippedwithcheckvalveportadaptersthatshouldnotberemoved.
Hooking up the motor in the wrong direction will damage the hydraulic seal.
*Hydraulicbackpressureinthereturnlinemustbelessthan100PSI[6.9bar]topreventreducedseallife. Pressures
under50PSI[3.4bar]arerecommended.
* For motors equipped with case drains the case drains must be used to minimize the pressure acting on the hydraulic
motor seal, and extend the life of the oil seal. The case drain line must be connected directly to the hydraulic reservoir with
no restrictions, and the case drain port on the motor must always be oriented upward.
THE CASE DRAIN PORT ON THE HYDRAULIC MOTOR MUST NEVER BE PLUGGED.
Commissioning, Start-Up, Operation, Shutdown
Beforeattemptingtostartyourpump,thefollowingmustbeunderstoodandfollowedtoensuresafeoperation.
Information
• When running Hypro centrifugal pumps, it is essential that operators use hearing protection as the sound levels
can reach levels of 80 decibels.
• When handling Hypro pumps, one should wear steel-toed shoes and protective gloves in order to protect the feet
in the event the pump is dropped and protect the hands from any sharp surfaces on the pump or chemicals.
• OnlyauthorizedoperatorshavingtheknowledgeandskillnecessarytosafelyuseaHypropump,orany
equipment the pump is connected to, may run the pump.
• Whensprayingmanually,itisrecommendedthatchemical-resistantfacemasksandclothingbeworntoprevent
anychemicalsfromcomingintocontactwiththeskinorbeinginhaled.
• When spraying manually, always spray downwind of yourself as long as the sprayed chemical will not drift into the
vicinity of other people.
• Wheninstalling,adjustingorremovingaHyprocentrifugalpump,ensurethattherearenoobjectswhichcanfall
ontheinstallerandmakecertainthatallmachinerytowhichthepumpistobeattachedisturnedoff.

11
Form L-1595
Rev. B
12-09-19
Priming the Pump
Tohelpprimethepump,keeptheinletorsuctionlineasshortaspossiblewithaminimumofbends,elbowsandkinks.
Makesureallconnectionsaretightanddonotleakair.Nonself-primingpumpsmusthavetheinletlineandpumpooded
withliquidbeforestartingthepump.Forself-primingmodels,thefrontchambershouldbelledwithliquidbeforestarting.
The pump must not be run dry.
Starting, Operation and Shutdown of the Pump (Hydraulic)
Open Center Systems - All Models
Adjusting Centrifugal Pump Output
ATTENTION HM3C motors have bypass screw fully closed from the factory.
1. Openthebypassadjustmentscrew2-1/2turnsfromfullyclosedandsecureitinplacewiththebypassjamnut.
2. Start the tractor. Leave the directional valve in the neutral position and allow hydraulic oil to circulate for approximately
10to15minutesoruntiladequatelywarmed.
3. Prime the centrifugal pump with all valves open. (See Priming the Pump.)
4. Refertosprayermanufacturer’smanualtosetsprayingpressureandow.Tochangetheoworpressuregenerated
bythepump,turnthebypassscrewonthehydraulicmotor.Besuretosecurethebypassjamnutafterany
adjustment.
5. To shutdown, return directional valve to neutral and allow the pump to come to a gradual stop.
When bypassing hydraulic oil, a large amount of heat can be generated which will damage the tractor’s hydraulic
system.Besuretomonitortheoiltempwhenbypassinghydraulicoil.
If the pump is not brought to a gradual stop, the sudden change in hydraulic pressure and pump RPM could cause
damage to the pump’s drive system.
• Hypro centrifugal pumps should only be used on tractors or tow-behind spray platforms which have electrically
conductivetiresinordertoreducetheriskofelectrocution.
• NeveroperateaHyprocentrifugalpumpoutsidewhilethereisachanceofgettingstruckbylightning.
• Never leave electrical wires or plumbing components where they can be a tripping hazard or become entangled
inamovingcomponent.Ideally,electricalcables,hoses,pipesandttingsshouldberoutedoverhead.Intheevent
electrical wiring must be routed over the ground, operators are required to use rubber ramps if they cross a gangway.
• Hypro centrifugal pumps should not be used if the ambient light is below 200lux.
Only use approved chemicals in your pump. For a complete list of approved chemicals, see the “Fluid
Pumping Applications” section. Failure to follow this warning will void your warranty and could lead to property
damage, serious injury or death.
Start-up, Operation, Shutdown
Before Starting the Pump
• Ensure all unnecessary personnel are clear of the area.
• Forinitialsetupandtestofyoursystem,itisrecommendedtostartwithcleanwaterinsteadofchemicals,andconrm
thesystemandplumbingconnectionsareleakfree.
• Ensurethatthereisuidinthesourcetankorsupplyline.Donotrundry.
• Checklinestrainerfordebrisorclogs.Removeanyfound.
• Checkallplumbingconnectionstomakesuretheyaretight.
• Checkpowersourceandconnections.
• Checkthatallvalvesandregulatorsaresettothedesiredsettingandarefunctioningproperly.
• Ensure all hoses are properly positioned and are not damaged in any way.

12
Form L-1595
Rev. B
12-09-19
Maintenance and Servicing
Information
• All maintenance should be done when machinery is stationary and has been isolated from its energy sources.
It is dangerous to perform maintenance while machinery is still connected to its power source. Machinery should be
isolated from its electrical, hydraulic or gas engine power source.
• BesuretoreleaseallpressurefromthesystembeforeperforminganysortofmaintenanceonaHypropump.
• DO NOT perform service or maintenance to the pump, or attached components, until the pump unit is below
109°F(43°C).
• The lubrication of this pump unit has been done at the factory prior to shipping.
• When handling Hypro pumps, one should wear steel-toed shoes and protective gloves in order to protect the feet
in the event the pump is dropped and protect the hands from any sharp surfaces on the pump or chemicals. If the
pump is being repaired while the pump is in service, eye protection should also be worn.
Any hazardous liquids should be disposed of in a manner which complies with local and national regulations. Never dump
uidsontotheground.
Disposal
WhendisposingofaHypropump,besuretoremovealluidsfromthepumpbeforescrapping.Theseuidsshouldbe
disposedofinamannerwhichcomplieswithlocalandnationalregulations.Neverdumpuidsontotheground.Oncethe
pumpisfreeofalluids,itmaybescrappedinaccordancewithlocalandnationallaws.
Closed Center (Pressure-Compensated) Systems
Adjusting Centrifugal Pump Output
1. Openthebypassadjustingscrewinthehydraulicmotorthree(3)turnsandsecureitinplacewiththebypassjamnut.
2. Startthetractorandallowhydraulicoiltocirculateforapproximately10to15minutesoruntiladequatelywarmed
3. Closeandlockdownthebypassadjustingscrewinthehydraulicmotor.
4. Prime the centrifugal pump with all valves open. (See Priming the Pump.)
5. Refertosprayermanufacturer’smanualtosetsprayingpressureandow.Tochangetheoworpressuregenerated
bythepump,slowlyadjusttractor’sowcontrolvalve.
6. Toshutdownthepump,movetheselectorforthetractorspoolvalvetotheoatpositionandallowthepumptocome
to a gradual stop.
If the pump is not brought to a gradual stop, the sudden change in hydraulic pressure and pump RPM could cause
damage to the pump’s drive system.
Closed Center (Load-Sensing) Systems
Adjusting Centrifugal Pump Output
1. Closeandlockdownthebypassadjustingscrew,ifequipped,inthehydraulicmotor.
2. Setthetractorhydraulicowcontrolvalveforminimumhydraulicoilowtotheremoteoutlet(Tortoiseposition).
3. Startthetractorandallowthehydraulicoiltocirculateforapproximately10to15minutesoruntiladequatelywarmed.
4. Prime the centrifugal pump with all valves open. (See Priming the Pump.)
5. Refertosprayermanufacturer’smanualtosetsprayingpressureandow.Tochangetheoworpressuregenerated
bythepump,slowlyadjusttractor’sowcontrolvalve.
6. Toshutdownthepump,movetheselectorforthetractorspoolvalvetotheoatpositionandallowthepumptocome
to a gradual stop.
If the pump is not brought to a gradual stop, the sudden change in hydraulic pressure and pump RPM could cause
damage to the pump’s drive system.

13
Form L-1595
Rev. B
12-09-19
Troubleshooting
Beforeattemptingtoserviceyourpump,besurethatitisdisconnectedfromallenergysources.
Symptom Probable Cause(s) Corrective Action
Pump does not prime Leakinsuctionline Checkhoseandttingsforleaksandcorrect
Obstruction in suction line Inspect hose for obstructions and remove
Suctionhosestucktotank Cut a notch or “V” in end of suction hose
Clogged strainer Checkstrainerandcleanregularly
Low discharge Pump not primed Remove topmost vent plug from face of pump
and run pump to expel trapped air
(See installation instructions).
Pump rotates incorrectly Hydraulichoseshookedupincorrectly
Leakinsuctionline Checkhoseandttingsforleaksandcorrect
Blockedsuctionline Inspect suction line and strainer, and repair as
necessary
Impeller plugged Inspect and clear obstruction
Undersized inlet line or collapsed
hose.
Suction line should be the same diameter as
inlet port of pump or larger.
Hydraulicbypassneedsadjustment See installation instructions
Pump worn Repair pump
Pump will not turn Hydraulichoseshookedupincorrectly See Installation instructions
Motor seized - contamination Repair or replace hydraulic motor
Hydraulic system overheating Hydraulicbypassneedsadjustment See Installation
Insufcienthydraulichosesize See Installation
Table 2
Cleaning
Yourpumpwilllastlongerandgivebestperformancewhenproperlytakencareof.Properpumpcaredependsonthe
liquidbeingpumpedandwhenthepumpwillbeusedagain.Aftereachuse,ushpumpwithaneutralizingsolutionforthe
liquidjustpumped.Followwithacleanwaterrinse.Thisisespeciallyimportantforcorrosivechemicals.Itisgoodpractice
to clean the pump after each use to prevent deposits from forming and damaging the pump. For infrequent use and before
long periods of storage, drain pump thoroughly. Open any drain plugs, remove suction hose from liquid, and blow pump
drywithair.Anantifreeze/rustinhibitorshouldbeinjectedintothepumpbeforebothportsarepluggedandthepumpis
stored.Plugallportstokeepoutairuntilpumpisusedagain.
Maintenance, Routine Servicing, and Inspection
PREVENTATIVE MAINTENANCE CHECKLIST
Check Daily Weekly
WaterLeaks X
Plumbing X
Filters X
• Eachsystem’smaintenancecyclewillbeexclusive.Ifsystemperformancedecreases,checkimmediately.
• Dutycycle,temperature,quality,typeofuidbeingpumped,andinletfeedconditionsallaffectthelifeofsprayboom
assemblies and service cycle.
• Beforeattemptingtoserviceyourpump,besurethatitisdisconnectedfromallenergysources.

14
Form L-1595
Rev. B
12-09-19
Replacement Parts
The following drawings show the pumps and their replacement parts. Only genuine replacement parts should be used.
Failure to follow this warning can result in damage to property, serious injury or death. If the pump malfunctions or
isdefective,itshouldbesentbacktoHyproforservice.
Hydraulic Motor Part No.
2540-1609C
Silicon Carbide Seal Kit No.
3430-0601
Containsoneeach:
Mechanical seal (Ref. 7) and
o-ring (Ref. 8).
Repair Parts Kit No.
3430-0500
Containsoneeach:
One o-ring (Ref. 8), one rubber
gasket(Ref.6),onemechanical
seal (Ref. 7).
NOTE:Whenorderingparts,
give QUANTITY, PART
NUMBER,DESCRIPTION,
and COMPLETE MODEL
NUMBER.Referencenumbers
are used ONLY to identify part
in the drawing and are NOT to
be used as order numbers.
Parts Kit No. 3430-0881
Contains:Oneeachball
bearing (Ref. 14), motor shaft
seal (Ref. 16), thread seal
gasket(Ref.34),andwasher
(Ref35);twoeachmotor
housing o-rings (Ref. 21), and
port adapter o-rings (Ref. 29
& 32).
9305C-HM3C, 9305C-HM3C-SP,
9305C-HM3C-BSP
Ref
No.
Qty
Req’d Part No. Description
1 4 2406-0016 Drain/Vent Plug
1A 1 2406-0002 1/2” NPT Drain Plug (SP Model Only)
1B 1 2406-0034 1” NPT Prime Port Plug (SP Model Only)
1B 1 2406-0036 1” BSP Prime Port Plug (SP Model Only)
2 1 0152-9200C Pump Casing
2A 1 3430-0481SP Self-Priming Chamber (SP Model Only) Includes Stainless Wear
Ring, Plugs & O-ring
2A 1 3430-0481BSP Self-Priming Chamber (BSP Model Only) Includes Stainless Wear
Ring, Plugs & O-ring
3 1 2253-0002 Impeller Nut
4 1 2270-0071 Washer
5 1 0403-9200P1 Impeller(Nylon)
6 1 3430-0500 Rubber Gasket
7 1 3430-0500 Mechanical Seal(Viton/Ceramic) (Std. 9305C)
7 1 3430-0601 Mechanical Seal(Viton/Silicone Carbide)
8 1 3430-0500 O-ring
9 1 0752-9200C Mounting Flange
10 6 2210-0086 Hex Head Cap Screw
11 1 1410-0056 Slinger Ring
12 1 1810-0014 Snap Ring
13 1 1820-0013 Retaining Ring
14 1 3430-0881 Ball Bearing
15 1 1410-0154 Spacer
16 1 3430-0881 Lip Seal
17 1 2029-0014 Thrust Bearing Assembly
18 1 3430-0856 Shaft
19 4 2210-0005 Bolt
20 1 0150-2540C Motor Body Non-Case Drain (Includes needle bearing)
8
9
36
27
26
29
28
35
34
32
33
21
24
25
23
22
10
37
38
39
18
16
15
14
13
12
11
6
5
4
3
1
1A
2A
1B
2
21
30
19
17
31
20
7
Ref
No.
Qty
Req’d Part No. Description
20 1 0150-2542C Motor Body Case Drain SAE -4 (Includes needle bearing)
21 1 3430-0881 O-ring
22 1 1600-0096 Dowel Pin (HM3)
23 1 1600-0085 Dowel Pin (HM3)
24 1 3900-0024 Gerotor (HM3)
25 1 0720-2606 Gerotor Housing (HM3)
26 1 0254-2500C2 Motor End Plate -8,-10 SAE, Bypass (Includes needle bearing)
26 1 0254-2500C3 Motor End Plate -8,-10 SAE, No Bypass (Includes needle bearing)
27 4 2270-0039 Washer
28 4 2220-0044 Cap Screw (HM3)
29 1 3430-0881 O-ring
30 1 3360-0021A Pressure Port Adapter (Includes o-ring)
31 1 3320-0051A Tank Port Adapter (Includes o-ring)
32 1 3430-0881 O-ring
33 1 3220-0029 Bypass Screw
34 1 3430-0881 Gasket
35 1 3430-0881 Washer
36 1 2250-0038 Lock Nut
37 1 1610-0055 Roll Pin
38 1 1810-0026 Snap Ring
39 1 1610-0053 Square key

15
Rev12/22/18
EC Declaration of Incorporation
Manufacturers Name: Pentair Flow Technologies, LLC
Manufacturers’ Address: 375 Fifth Avenue NW,
New Brighton, MN 55112, USA
Declare that the partially complete machinery described below conforms to applicable health and safety requirements of Emission Directive
2010/26/EU and of Parts 1 of Annex I of Machinery Directive 2006/42/EC. This partly completed machinery must not be put into service until the
equipment into which it is to be incorporated has been declared in conformity with the provisions of these directives. Confidential technical
documentation has been compiled as described in Annex VII Part B of Machinery Directive 2006/42/EC and is available to European national
authorities on written request. If a request is received, documentation will be transmitted either electronically or by post. Clauses 1.1.4, 1.1.7,
1.1.8 Section 1.2, Clauses 1.3.5, 1.3.6, 1.3.7, 1.3.8.1, 1.3.8.2, 1.3.9, 1.4.1, 1.4.2.1, 1.4.2.2, 1.4.2.3, 1.4.3, 1.5.2, 1.5.7, 1.5.12, 1.5.14, 1.5.16, 1.6.2, 1.7.1.1, 1.7.1.2,
1.7.2, and 1.7.4.2 are clauses of Machinery Directive 2006/42/EC that have not been met, but could be applicable and must be addressed during
installation by a third party.
Description: PENTAIR Pump
Type: Roller Pumps
Series Numbers 1502, 1700, 4001, 4101, 6500, 7560, 7700
Type: Centrifugal Pumps
Series Numbers 1442P, 1539, 1540, 1542P, 1543P, 1550, 90XX, 9202, 9203, 9205, 9206,
9208, 9262, 9263, 9253, 9302, 9303, 9305, 9306, 9307, 9308, 9313, 9314,
9316, 9342P, 9343P, 9742P, 15HPS, 93HPS
Type: Cleanload Assembly
Series Numbers 3376, 3378
Type: Piston/Plunger Pumps
Series Numbers 5315C, 5320C, 5321C, 5322C, 5324C, 5325C, 5330C, 53702, 53703
The following standards have either been referred to or been complied with in part or in full as relevant:
ENISO 12100 Machinery Safety - General principles for design - Risk assessment and risk reduction
EN809-1998 + A1 2009 Machinery Safety - Pumps and pump units for liquids - Common safety requirements
EN ISO 13732-1 Machinery Safety - Ergonomics of the thermal environment
EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of
noise sources using sound pressure
EN ISO 11202/A1 1997 Machinery Safety - Noise emitted by machinery and equipment
EN 12162:2001+A1:2009 Machinery Safety - Liquid pumps - Safety requirements-Procedure for hydrostatic testing
EN ISO 4254-6:2009 Machinery Safety - Sprayers and liquid fertilizer distributors
EN 60204-1:2006/A1:2009 Machinery Safety - Electrical Equipment of Machines
Name .……………...…………………………………………… Position…..……………………….…..………
Signature …………………………………………..……………. Date…..……..………………………..……….
Place of Signing…………………………………………………………………………………………………….…..
Rev12/22/18
EC DECLARATION OF INCORPORATION

For a detailed list of where Pentair trademarks are registered, please visit www.pentair.com/en/registrations.html. Pentair trademarks and logos are owned by Pentair PLC. or its aliates.
Third party registered and unregistered trademarks and logos are the property of their respective owners. Because we are continuously improving our products and services, Pentair
reserves the right to change specications without prior notice. Pentair is an equal opportunity employer.
L-1595 Rev. B (12-09-19) ©2019 Pentair. All Rights Reserved.
Hypro/Shurflo (hereafter, “Hypro”) agricultural products are warranted to be free of defects in material and workmanship under normal use
for the time periods listed below, with proof of purchase.
- Pumps: one (1) year from the date of manufacture, or one (1) year of use. This limited warranty will not
exceed two (2) years, in any event.
- Accessories: ninety (90) days of use.
This limited warranty will not apply to products that were improperly installed, misapplied, damaged, altered, or incompatible with fluids or
components not manufactured by Hypro. All warranty considerations are governed by Hypro’s written return policy.
Hypro’s obligation under this limited warranty policy is limited to the repair or replacement of the product. All returns will be tested per
Hypro’s factory criteria. Products found not defective (under the terms of this limited warranty) are subject to charges paid by the returnee
for the testing and packaging of “tested good” non-warranty returns.
No credit or labor allowances will be given for products returned as defective. Warranty replacement will be shipped on a freight allowed
basis. Hypro reserves the right to choose the method of transportation.
This limited warranty is in lieu of all other warranties, expressed or implied, and no other person is authorized to give any other warranty or
assume obligation or liability on Hypro’s behalf. Hypro shall not be liable for any labor, damage or other expense, nor shall Hypro be liable for
any indirect, incidental or consequential damages of any kind incurred by the reason of the use or sale of any defective product.
RETURN PROCEDURES
All products must be flushed of any chemical (ref. OSHA section 1910.1200 (d) (e) (f) (g) (h)) and hazardous chemicals must be labeled/tagged
before being shipped†to Hypro for service or warranty consideration. Hypro reserves the right to request a Material Safety Data Sheet from
the returnee for any pump/product it deems necessary. Hypro reserves the right to “disposition as scrap” products returned which contain
unknown fluids. Hypro reserves the right to charge the returnee for any and all costs incurred for chemical testing, and proper disposal
of components containing unknown fluids. Hypro requests this in order to protect the environment and personnel from the hazards of
handling unknown fluids.
Be prepared to give Hypro full details of the problem, including the model number, date of purchase, and from whom you purchased your
product. Hypro may request additional information, and may require a sketch to illustrate the problem.
Contact the appropriate Hypro Service Department to receive a Return Merchandise Authorization number (RMA#).
Returns are to be shipped with the RMA number clearly marked on the outside of the package. Hypro shall not be liable for freight damage
incurred during shipping. Please package all returns carefully. All products returned for warranty work should be sent shipping charges
prepaid:
LIMITED WARRANTY ON HYPRO/SHURFLO AGRICULTURAL PUMPS & ACCESSORIES
AMERICAS & ALL OTHER REGIONS
Hypro / Pentair
Attention: Service Department
375 Fifth Avenue NW
New Brighton, MN 55112
Service: 800-468-3428
Fax: [phone]
Technical: 800-445-8360
hypro.technicalpentair.com
CANADA
Pentair Water Belgium B.V.B.A
Industriepark Wolfstee
Toekomstlaan 30, 2200
Herentals, Belgium
Tel: [phone]
Fax: [phone]
shur[e-mail]
CENTRAL & SOUTH AMERICA
[phone]
[e-mail]
pentair.com
† Carriers, including U.S.P.S., airlines, UPS, ground freight, etc., require specific identification of any hazardous material being shipped. Failure to do so may result in a substantial fine and/or prison term.
Check with your shipping company for specific instructions.