Pentax T18 Series User manual

Page | 0
T18
User Manual
Version 1.00
Revision Version 1.00, September 2020
TI Asahi Co., LTD

Page | 1
T18 User Manual
© 2017 TI Asahi Co., Ltd. All rights reserved. PENTAX, the PENTAX logo are trademarks registered
in the U.S. and other countries. No part of this document may be copied, used or reproduced without
the prior written permission of TI Asahi.
No part of this manual may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose without the express written permission
of TI Asahi Co., Ltd.
Mention of third-party products in this document is for informational purposes only and does not
constitute an endorsement or a recommendation. TI Asahi assumes no responsibility with regard to the
performance or use of the T18 due to GPS characteristics, USA Department of Defense operations
control, atmospheric effects, multipath and RF interference. All understandings, agreements, or
warranties take place directly between the seller and the prospective users. Every effort has been made
to ensure that the information in this manual is accurate. TI Asahi is not responsible for printing or clerical
errors. All specifications are typical and subject to change without prior notice.
Exemption clause
1) TI Asahi Co., Ltd. (TIA) shall not be liable for damage caused by Acts of God, fire, alteration or
servicing by unauthorized parties, accident, negligence, misuse, abnormal operating conditions.
2) TIA shall not be liable for changes or disappearance of data, loss of company profit or interruption
of company operation incurred by the use of this product or malfunction of it.
3) TIA shall not be liable for damage caused by usage not explained in the instruction manual.
4) TIA shall not be liable for damage to this product caused by other equipment connected to this
product.
Before using this product, be sure that you have thoroughly read and understood this instruction
manual to ensure proper operation. After reading this manual, be sure to keep in a convenient place for
easy reference.

Page | 2
Table of Content
1. Introduction .............................................................................................................. 4
1.1. Features ............................................................................................................. 4
1.2. Keyboard ............................................................................................................ 4
1.3. LED Functions ..................................................................................................... 6
2. Getting Acquainted ................................................................................................ 6
2.1. Installing the TF card/SIM card/Battery............................................................... 6
2.2. Charging ............................................................................................................. 7
2.3. Turning the collector on/off ................................................................................ 7
2.4. Connecting to a PC ............................................................................................. 7
2.5. Installing Applications ......................................................................................... 8
2.5.1. Installing Applications via ActiveSync or WMDC .............................................. 8
2.5.2. Directly Installing Applications ........................................................................ 9
2.6. GNSS status ........................................................................................................ 9
2.7. Camera ............................................................................................................. 10
2.8. User Serial Port ................................................................................................. 10
2.9. Wireless Connection (Bluetooth/GPRS/WIFI) .................................................... 10
2.9.1. Standard Bluetooth ....................................................................................... 10
2.9.2. Long Range Bluetooth (Optional) .................................................................. 11
2.9.3. Wi-Fi ............................................................................................................. 12
2.9.4. GPRS/3G Data connection ............................................................................. 13
3. Useful Functions................................................................................................... 13
3.1. Screen response ............................................................................................... 13
3.2. Adjusting the backlight ..................................................................................... 13
3.3. Removing programs.......................................................................................... 13
3.4. Auto power off* ............................................................................................... 13
3.5. Clean Boot ........................................................................................................ 14
3.6. PWConfig ......................................................................................................... 14

Page | 3
4. Accessories .......................................................................................................... 14
4.1. Standard Accessories ........................................................................................ 14
4.2. Optional Accessories ........................................................................................ 15
5. Environmental Specifications ............................................................................... 15
6. Warranty Terms ................................................................................................... 15
7. Appendix – Product Safety Warnings .................................................................... 16

Page | 4
1.Introduction
1.1. Features
The following section describes the general features of the T18 Handheld Controller.
Figure 1-1: General Diagram
1.2. Keyboard
The yellow symbols are system defaults.

Page | 5
Table 1-1. Keyboard Function
System Default
System defaults to the digital input method
,
.
Press↑（shift）
Lowercase letters
Switch between / and -
*
#
Press↑(shift) again, to switch to digital input method.
Press Caps
Capital letters
Switch between / and -
*
#
Press the Caps button again for lowercase letters.

Page | 6
1.3. LED Functions
Table 1-2, LED Functions
2. Getting Acquainted
2.1. Installing the TF card/SIM card/Battery
a) Turn the back cover screw to the open position according to the instructions on a label in the box, and
take off the back cover.
Figure 2-1: Opening the Back Cover
b) Insert the SIM card and TF card according to the instructions in the battery cabin.
Figure 2-2:
Inserting the SIM Card
c) Insert the battery according the instructions on the battery label( Figure 2-3).
Operation
Power off
Charging
Fully of charged
In use
LED Status
Off
Red light on
Off
Off

Page | 7
Figure 2-3: Inserting the Battery
d) Close the back cover and turn the back cover screw to the lock position.
2.2. Charging
a) DC adapter: Open the DC IN cover on the right side of the device, and charge with the DC adapter.
Charging current can reach 2A.
b) USB cable: A USB cable can also be used to charge the device, and current is limited to 500mA.
2.3. Turning the collector on/off
a) Make sure the battery has enough power, or connect the T18 to a DC adaptor.
b) Press power button for three (3) to five (5) seconds to turn on (until the boot screen appears).
c) Press the power button for three (3) to five (5) seconds, and confirm to power off.
NOTE: If there are abnormal situations, such as the T18 does not operate normally, use the tip of the stylus
to press the reset key to restart the T18.
2.4. Connecting to a PC
a) Make sure Microsoft ActiveSync application has been installed in Win-XP PC. And make sure WMDC
(Windows Mobile Device Center) has been installed in Vista/Win7/Win8 PC.
b) Connect T18 to a PC with USB cable.
c) ActiveSync/WMDC will connect to T18 and PC automatically. The icon will appear in the tool bar of
PC and also the Synchronization Setup Wizard. In the meantime, click Cancel or connect without
setting up your device.
d) Click Browse to check the files in the T18, and then transfer data between your PC and the T18.

Page | 8
2.5. Installing Applications
2.5.1. Installing Applications via ActiveSync or WMDC
a) Make sure the T18 is connected with your PC via ActiveSync or WMDC.
Figure 2-4: T18 Connected with PC
b) Click the installation file on your PC to start the installation of an application.
Figure2-5: Installing the Applicationg
c) Select an installation directory in the T18（Flash Storage is suggested）, and tap install.

Page | 9
Figure 2-6: Choosing Install Location
NOTE: We suggest installing the application in Flash Storage, and saving your data to a TF card.
2.5.2. Directly Installing Applications
If the installation file is compatible on mobile devices, copy the file into the T18 and tap the file to directly
start the installation.
2.6. GNSS status
a) Go to \My Device\GNSSViewer and run GNSSViewer.exe
b) T18 supports COM3 as GNSS ports and its BaudRate is 9600. Choose a GPS Port and BaudRate by
tapping Setup>Port Setup as shown in Figure 2-7.
NOTE: COM3 is a hardware GNSS port.

Page | 10
Figure 2-7: GNSS Status
c) Tap OK
Figure 2-8: GNSS Status
2.7. Camera
a) Select Start>Picture & Video, select Camera or the camera key icon to take photos.
b) Press the camera key (F3) to take photos.
c) Tap screen and select OK to exit.
2.8. User Serial Port
The user serial port is COM2. To transfer data between the T18 and other devices using a DB9 serial cable.
NOTE: This user serial port is at the bottom of the T18.
2.9. Wireless Connection (Bluetooth/GPRS/WIFI)
2.9.1. Standard Bluetooth
a) Select Start>Settings>Connections>Wireless Management, tap the icon to activate the
Bluetooth(BT) device.
b) Select Start> Settings> Bluetooth, and tap Add new device…. Follow the tips shown on the screen to
finish the operation of pairing the other BT Device.
NOTE: The standard Bluetooth virtual ports are COM7 and COM9.

Page | 11
2.9.2. Long Range Bluetooth (Optional)
a) Select Start>Settings>System, and tap Bluetooth Radio Manager.
Figure 2-9: Bluetooth Radio Manager
b) Chose the module DirectConn, and tap Power On.
c) Tap Search BT to start searching for BT devices.
d) After all BT devices have been found, select a device.
e) Tap Connect to pair with a BT device of your choice. Your screen will display Connect the BT device
successfully after BT pairs successfully.
Figure 2-10: BT Manager-DirectConn
f) Tap Console to check the status of Bluetooth, as shown below.

Page | 12
Figure 2-11: BT Manager-Status
g) Tap Setup to setup this Bluetooth, as shown below.
Figure 2-12: BT Manager-Setup
h) The default baud rate is 38400.
i) The PIN code refers to the pairing PIN code of the BT device which T18 want to pair with.
j) If you check Auto Conn, T18 will automatically connect to the last pairing BT device when powered up.
NOTE: Long Range Bluetooth port is COM2 which is the same as user serial port. If Long Range Bluetooth
been used, user serial port is disable.
2.9.3. Wi-Fi
a) Select Start>Settings>Connections>Wi-Fi.
b) Tap Search for Networks, select a network listed. Follow the installation guide to input a password and
confirm connection to Wi-Fi.

Page | 13
2.9.4. GPRS/3G Data connection
a) Make sure there is a SIM card in the T18.
b) Select Start>Settings>Connections>Connections.
c) Tap Add a new modem connection.
d) Input connection name, select Cellular Line (GPRS), and tap Next.
e) Input Access point name, tap Next.
f) Tap Finish and add new connection successfully.
g) Tap Manage existing connections.
h) Tap and hold on new connection and select Connect.
i) If there is the identifier on the signal icon in the top right corner, this indicates a successful.
3. Useful Functions
3.1. Screen response
Select Start> Settings> System> Screen , tap the A lign Screen icon and follow the guide to align the screen.
Figure 3-1: Align Screen
3.2. Adjusting the backlight
Select St ar t> Settings> System> Backlight to adjust backlight according to the guide.
Figure 3-2: Backlight
3.3. Removing programs
Select St ar t> Settings> System> Remove Programs , select the programs you wish to remove in the list
and, click OK to remove.
Figure 3-3: Remove Program
3.4. Auto power off*
(*NOTE: The device does not support the Auto power off function, instead use Go-to-sleep mode.)

Page | 14
Select Start> Settings> System> Power> Advanced, set the power off time in different conditions. Backlight
will be off according to selected settings.
Figure 3-4: Go-to-Sleep Mode
3.5. Clean Boot
Select Start> Settings> System> Clean Boot, to restore factory default settings according to the guide.
Figure 3-5: Clean Boot
NOTE: The password is “1234”. Restoring factory settings will clear the system configuration, please be
cautious.
3.6. PWConfig
Select Start> Settings> System> PWConfig.
NOTE: While on Screen off mode, the device won’t hibernate.
Figure 3-6: PWConfig
4. Accessories
4.1. Standard Accessories
Table 4-1, Stardand Accessories
Item
Name
Description
Quantity
1
DC Adapter
220V/DC5V/2A
1
2
USB cable
USB to B-TYPE USB cable
1
3
Serial cable
DB9 serial cable
1
4
Li-ion Battery
3.7V/6500mAh
1
5
Strap
Black, 180*12mm
1
6
Stylus
Black, 127mm
1
7
Screen protection film
57*76mm, 3H & Screen Microfiber Cloth
2
8
User guide
Size,14*21cm
1

Page | 15
4.2. Optional Accessories
Table 4-2, Optional Accessories
5. Environmental Specifications
a) Operating ambient temperature: -20℃ to +60℃
b) Non operating temperature: -30℃ to +70℃
c) Drop: 1.5m drop tested on all surfaces
d) Water and Resistant: Rated IP65 under IEC 60529
e) Relative humidity: 5% ~ 95% , non-condensing
6. Warranty Terms
T18 Series are guaranteed against defective material and workmanship under normal use and application
consistent with this Guide. The equipment is guaranteed for the period indicated, on the warranty card
accompanying the product, starting from the date that the product is sold to the original purchaser by
PENTAX Authorized Dealers.
During the warranty period, at its option, repair or replace this product at no additional charge. Repair parts
and replacement products will be furnished on an exchange basis and will be either reconditioned or new.
This limited warranty does not include service to repair damage to the product resulting from an accident,
disaster, misuses, abuse or modification of the product.
Warranty service may be obtained from an authorized PENTAX warranty service dealer. If this product is
delivered by mail, purchaser agrees to insure the product or assume the risk of loss or damage in transit, to
prepay shipping charges to the warranty service location and to use the original shipping container or
equivalent. A letter should accompany the package furnishing a description of the problem and/ or defect.
Item
Name
Description
Quantity
1
TF card
Memory Capacity: 8G
1
2
External battery charger
5V/2A
1
3
Mounting bracket and
Pole (Claw) Clamp
HW-02
1
4
External GNSS antenna
GPS L1, BD B1, Glonass G1
Gain: 40dB
TNC Connector
1
5
External antenna cable
Fischer to TNC cable
1
6
TNC to TNC cable
TNC male to TNC male cable, 3m long
1
7
Centering rod
Centering rod
1

Page | 16
The purchaser’s sole remedy shall be replacement as provided above. In no event shall PENTAX be liable for
any damages or other claim including any claim for lost profits, lost savings or other incidental or
consequential damages arising out of the use of, or inability to use, the product.
NOTE: Please use the original factory parts.
7. Appendix – Product Safety Warnings
Safety and compliance information
• Use responsibly –Read all instructions and safety information before use to avoid injury.
Battery safety
• Charge battery only in temperature ranging from 32℉ to 140℉ (0℃ to 50℃ )
• CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type of battery recommended by the manufacturer.
• The maximum operating ambient temperature of the switching power supply declared by the
manufacturer is 50℃.
• Dispose of used batteries according to battery manufacturer’s instructions.
Wi-Fi safety
• Turn Wi-Fi off in areas where Wi-Fi use is prohibited or when it may cause interference or danger, such
as in airplanes while flying.
Care and maintenance
T18 is an electronic product and should be treated with care. To reduce the risk of fire, electronic shock, or
product damage take the following advice:
• Do not expose this device to rain, moisture, or any type of liquid that corrodes electronic circuits. If
your device gets wet, immediately turn the power off. Allow the device to dry completely before using
it again.
• Clean the display with a soft cloth, and be careful not to wipe the display with anything abrasive.
• Do not expose your device to extreme heat (60℃ ) or cold (-20℃ ). For example, do not leave it in
the trunk of your car in high heat conditions.
• Do not attempt to open the device other than as instructed in this manual.
• Rough handling can break internal circuitry.
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
• Use only the recommended accessories.

Page | 17
CAUTION!
CONNECTION TO A USB INTERFACE MUST BE LIMITED TO
USB2.0 VERSION OR HIGH E R
CONNECTION TO “POWER USE” MODE IS PROHIBITED.