Perfect Pool PP2 User manual

INSTALLATION MANUAL
NOTE TO INSTALLER:
GIVE THIS MANUAL TO OWNER
OPERATOR AFTER INSTALLATION
!
PERFECT POOL OZONE GENERATOR
18 North Dollins Ave, Orlando, FL 32805 Tel/Fax: [phone] nspdevelopment.com
IN DECK CIRCULATION/FILTRATION UNIT
PP2 Ozone System
(No Filter Cartridge)
PP3 Ozone System
(With Filter Cartridge)

INSTALLATION MANUAL
2.
The Ozone Generator requires the use of a GFCI as the power source when wired 120V
3.
4.
5.
6.
SAFETY PRECAUTIONS
!
WARNING - To prevent electrocution and/or death make sure power is off at the breaker.
1.
7.
WARNING - To reduce the risk of injury, do not permit children to use this
product unless they are closely suprevised at all times.
18 North Dollins Ave, Orlando, FL 32805 Tel/Fax: [phone] nspdevelopment.com
!
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electric equipment, basic safety precautions should always
be followed including the following:
READ AND FOLLOW ALL INSTRUCTIONS
WARNING - Risk of Electric Shock. Connect only to a grounding type receptacle protected by
a ground-fault circuit-interrupter (GFCI). Contact a qualified electrician if you cannot verify that
the receptacle is protected by a GFCI.
Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers and other
equipment.
WARNING - To reduce the risk of electric shock, replace damaged cord immediately.
WARNING - To reduce the risk of electric shock, do not use extension cord to connect unit to electric
supply; provice a properly located outlet. Avoid touching/installing the Perfect Pool Ozone Generator
box during electric storms. Death or serious injury may result due to lightning surges through the
system. Be sure to check local electrical code for grounding electrical boxes via the approved method
(internal conduit ground,external box ground to grounding rod, Ground Fault Circuit Interupter or GFCI,
etc.)
8.
11.
9.
10.
Use approved conduit routed by approved methods to conduit fittings on the unit.
Be sure the mounting surface is able to support the load of the controller. Use all mounting hoels
to secure the unit.
There are no customer servicable components inside the Perfect Pool Ozone Generator. Only qualified
electricians should open the unit for installation. All connections should enter an approved conduit
method.
SAVE THESE INSTRUCTIONS
ADDITIONAL PRECAUTIONS
A.DIRECT INHALATION OF OZONE GAS FOR PROLONGED PERIODS CAN BE DETERIMENTIAL
TO YOUR HEALTH
B.This unit produces Ozone Gas, a highly agressive oxidizing agent. It is intended only to be used in
pool/spa OUTDOOR environments.
C.The Ozone Generator cannot be located within 5 ft of pool waters edge.
D.This Ozone Generator must be installed in accordance to Article 680 of the NEC and local code
requirements.

INSTALLATION MANUAL
DU E TO THE DESIRED WATER RESISTANT SEAL OF THE ENCLOSURE, DO NOT
REMOVE ANY KNOCKOUTS UNLESS THAT HOLE WILL HAVE A CONDUIT INSTALLED.
IF A KNOCKOUT IS ACCIDENTALLY REMOVED, STEPS MUST BE TAKEN TO RESEAL
THE OPENEING OR THE PERFECT POOL OZONE GENERATOR WILL BE DAMAGED.
MOUNTING INSTRUCTIONS
WARNING
!
MOUNTING
PAD MOUNT
1. Place unit on a secure concrete pad. (see Fig.1)
2. Use the four (4) mounting holes to secure the unit to the pad or mounting surface.
WALL MOUNT
1. Select a mounting location so that the bottom surface of the unit will be raised above the ground
or placed on a secure concrete pad. (see Fig.2)
2. Remove cover and locate the four (4) mounting holes (Fig.2) to secure the unit to the pad or mounting surface.
3. After securing unit to the wall replace cover and secure with the cover screws.
Concrete
Pad Perfect Pool
Ozone Gen.
Pad Mount Fig. 1
Mounting Holes (4)
two on each side Wall
Perfect Pool
Ozone Gen.
Wall Moung Fig. 2
Mounting Holes (4)
(Remove Cover)
18 North Dollins Ave, Orlando, FL 32805 Tel/Fax: [phone] nspdevelopment.com

INSTALLATION MANUAL
UNIT OVERVIEW
EXTERIOR VIEW
INTERIOR VIEW
120 VAC
WHITE: NEUTRAL
BLACK: LINE
GREEN: GROUND
Mounting Holes
(4 total)
ON / OFF Switch
120VAC
Power
Switch
Ozone /
Air Out to Filter
S
Line In(Black)
Ballast
Switch
Pump
Neutral (White)
Ground (Green)
Internal Wiring
Schematic
NOTE:
Components may
change as Unit
model changes
18 North Dollins Ave, Orlando, FL 32805 Tel/Fax: [phone] nspdevelopment.com

There are 3 key installation points that must be adhered to for proper operation.
1. The In deck filter module must be installed at a level of where the pool water is
equal to the bottom of the BLACK COUPLER.
THIS IS THE MOST
CRITICAL INSTALLATION POINT
2. Conduit must be run from the In Deck Filter module to the Generator assembly
located at the equipment pad. Since time to time this conduit will have water/
moisture in it, it needs to be properly glued the entire length.
3. The Water Inlet (suction—middle pipe on filter base) should be located as low in
the pool wall as possible. The Water Return ( outside pipe on filter base) should
be located as high as possible on pool interior wall.
THE MOST CRITICAL INSTALL POINT IS MAKING SURE THE POOL WATER
LEVEL IS ALIGNED WITH THE BOTTOM OF THE BLACK COUPLER ON THE
FILTER MODULE
INSTALLATION MANUAL
IN DECK FILTER MODULE INSTALL INSTRUCTIONS
18 North Dollins Ave, Orlando, FL 32805 Tel/Fax: [phone] nspdevelopment.com
Pool Water Level should
align with bottom of
Black Filter Coupler

THERE ARE 4 CONNECTION ON FILTER BASE
1. 1 1/2" Inlet fitting - this is located in the direct
center of the Filter BAse
2. 1 1/2” Return fitting located on the extreme
outside of filter base.
3. There are 2—1” fittings that are blocked off.
They do not pass into the interior of filter base.
INSTALLATION MANUAL
IN DECK FILTER MODULE INSTALL INSTRUCTIONS
18 North Dollins Ave, Orlando, FL 32805 Tel/Fax: [phone] nspdevelopment.com
1
2
SECURING FILTER MODULE
There are 4 TABS located in the center
area of the Black Coupler or Collar. 2
of the are shown here. These TABS are
to be used to secure the Filter Assembly
to rebar used in the deck area.
By securing the filter module to rebar
you can also ensure that the POOL
WATER LEVEL aligns with the bottom
of the Black Coupler.
POOL WATER LEVEL ALIGNMENT
ADJUSTING TO DECK POUR HEIGHT
The collar on the top of the Filter
Module is not glued and can be raised
and tilted to match deck level around
pool area.
1
2
3
These 1" glue fittings provide the ability to
glue in 1" pipe to be used as support pipes
for the filter module itself.

1.
Attach tubing to Straight barb fitting contained in bag.
2.
Secure tubing to barb with enclosed hose clamp.
3.
Run 1” conduit from In Deck Filter to equipment pad or wherever Generator is located.
Make sure to use “sweep” fitting—no 90 degree elbows should be used as replacement of
tubing would be very difficult.
4.
Run Tube from In Deck Filter to Oxone Generator and attach to Check Valve
located inside Ozone Generator.
5. Push Slip fitting with barb/hose into filter receiver fitting on side wall.
6. Thread in 90 degree fitting and attach diffuser and hose. Insert under Chlorine Cartridge "Birdcage" and
into the Filter cartridge 1 1/2" pipe. Make sure the diffuser is pushed down towards bottom of pipe.
INSTALLATION MANUAL
TUBING & DIFFUSER INSTALL INSTRUCTIONS
18 North Dollins Ave, Orlando, FL 32805 Tel/Fax: [phone] nspdevelopment.com

The cartridge filter and the diffuser itself will need
cleaning from time to time.
The cartridge filter is removed by the following steps.
1. Turn Ozone Generator off using on/off switch on unit
2. On the inside of the In Deck Filter module - remove
the diffuser and 90 degree wall fitting.
3.
5.
Now g ently pull the cartridge element from the
body. Hose off unit debris is gone.
Reverse steps for installation.
The ozone diffuser can be cleaned by soaking in vinegar or lemon juice. These mild acids will remove
oxodized debris from ozone diffuser surface. We recommend that you have 2 Ozone Diffusers on
hand so that they can be simply exchanged during cleaning, allowing dirty diffuser to soak till clean.
Also these can be cleaned with liquid Muratic Acid. This will quickly clean the Ozone Diffuser.
PLEASE BE VERY CAREFUL IN THE USE OF THIS MATERIAL AS IT IS EXTREMELY
HARMFUL. LIQUID MURATIC ACID IS USED TO ADJUST Ph IN SWIMMING POOLS.
INSTALLATION MANUAL
Service Instructions
FILTER ASSEMBLY
Unscrew the red Chlorine Cartridge birdcage. If unit
has chlorine cartridge attached - this must also be
removed at this time.
4.
Ozone Diffuser
The Ozone Diffuser will last for many years since it is
made of materials specifically designed for ozone gas
utilization BUT it will become very visably "dirty" from
all the materials the ozone gas is oxidizing from the
water. The diffuser is at this initial oxidation point. The
ozone diffuser will turn from its normal white to a dirty
brown or in some cases even black. There can be also
evidence of redish material which can be an indicator
metal particulates in the pool water. This is usually only
seen on pools that have been filled from well systems.
18 North Dollins Ave, Orlando, FL 32805 Tel/Fax: [phone] nspdevelopment.com

INSTALLATION MANUAL
Service Instructions
18 North Dollins Ave, Orlando, FL 32805 Tel/Fax: [phone] nspdevelopment.com
OZONE BULB REPLACEMENT
The Ozone Bulb assembly should be replaced every
36 months -EVEN IF IT IS STILL OPERATIONAL.
The Ozone Bulb assemby has been made so that
anyone can replace these easily and quickly.
Turn off circuit breaker that supplies power to
the Ozone Generator.
1.
2.
3.
4.
Disconnect the 4 wire connector so that
you have 2 halves.
Remove the hose from each end of the ozone bulb assembly.
Final step is to push down on the middle of each clamp until they clamps union comes apart. You will have
to do each clamp individually. The Ozone Bulb assembly is now removeable from can assembly.
5.Insert new ozone bulb assembly and reinstall going from steps 4 to 1.
TROUBLESHOOTING GUIDELINES
There can be only 3 areas to check if you think your Perfect Pool PP2 or PP3 is not operating correctly: The Ozone
Generator air pump (1) - the ozone bulb assembly (2) or the Ozone Diffuser
1.
In most all cases utilizing a small vial of Phenol Red dye (#2) available at any pool store or store selling pool chemicals.
Pheno Red is used to test swimming pool Ph.
The first thing to check is to ensure that power is going to the Ozone Generator unit.
2.
4.
3.
To check for proper operation off these units - open lid assembly and pour in Phenol Red
solution.
If unit is operating correctly - you will see a PURPLE dye coming from the Perfect Pool return wall fitting in
pool. This verify's that the air pump is working - air hose is connected and clear - diffuser is clean enough for
bubble operation AND that the ozone bulb is still prodoucing ozone as it's oxidized the Phenol Red to purple.
If Phenol Red enters pool still RED in color this is an indication that the Ozone Bulb needs replacing -
replace per instruction and rerun Phenol Red test to verify proper operation.
6.
5.Upon opening of In Deck Filter assembly and there is no bubbles being generated then there check to ensure
power is on - air pump is operating and air tubing is still connected between Ozone generator and Filter. If
not identify where problem is and repair. Contact Customer Service for additional information.
Always check Ozone Diffuser & Filter anytime there is low flow rate coming back into pool. Clean as
neccessary to achieve correct flow rate.

NSP Development 18 North Dollins Avenue, Orlando, Florida 32805 Phone:[phone] Fax:[phone]
NSPdevelopment.com
NAME:
ADDRESS:
CITY:
STATE:
ZIP CODE:
EMAIL:
MODEL:
PP-1 OZONE GENERATOR
PP-2 IN-DECK OZONATION MODULE + OZONE GENERATOR
PP-3 IN-DECK OZONATION & FILTRATION MODULE + OZONE GENERATOR
SERIAL NO. :
PRODUCT REGISTRATION
3 Ways to Register your product:
1. Complete this form on-line and email to: [e-mail]
2. Print the form out and fax to: 1.855.996.6900
3. Mail the form to: NSP Development 18 North Dollins Avenue, Orlando, Florida 32805
NSP Development will ship you 1 FREE Ozone Diffuser upon the registration of your Perfect Pool unit. This
will allow for instant ozone diffuser swap outs when cleaning is necessary without have to wait.
Thank you again for your Perfect Pool purchase and welcome to the best pool water possible.