Perlesmith PGDSK1 User manual

Tools Needed
CAUTION!MAXIMUM WEIGHT CAPACITY
WARNING!
WEIGHT CAPACITY
!7.5 kg
16.5 lbs
USE WITH PRODUCTS LARGER THAN THE MAXIMUM WEIGHT AND SIZE MAY RESULT IN INSTABILITY CAUSING POSSIBLE
INJURY. USER MUST REMOVE TELEVISION OR OBJECT OFF THE BRACKET BEFORE ADJUSTING. NOT SUITABLE FOR A TV THAT
SURPASSES THE TELEVISION MAXIMUM WEIGHT CAPACITY AND RECOMMENDED DIAGONAL MEASURED TV SIZE!
*
*
*
*
*
WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER INSTALLATION OR ASSEM-
BLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.
If you do not understand the instructions or have any concerns or questions, please contact a qualified installer.
Do not install or assemble if the product or hardware is damaged or missing. Not all parts and hardware included must be used. If you require
replacement parts, contact customer service at [email protected].
Do not attempt to install or assemble this product if the product or hardware is damaged or missing. The included hardware is designed for
use on vertical walls constructed of wood studs or concrete. A wood stud wall is defined as consisting of a minimum of 2x4 wooden studs (2”
wide by 4” deep) with a maximum of 5/8” drywall. The included hardware is not designed for use with metal studs or cinderblock walls. If
you’re uncertain about the construction of your wall, then please consult a qualified contractor or installer for assistance. For a safe
installation, the wall you are mounting to must support 4 times the weight of the total load. If not, then the surface must be reinforced to meet
this standard. The installer is responsible for verifying that the wall structure and hardware used in any installation method will safely support
the total load.
Please check www.perlesmith.com for more products and company information.
SINGLE SHELF WALL MOUNT
MODEL: PGDSK1
C
B
AX2
X1
X2
Cable manager End cap
D
X1
Glass Shelf
Stud
Finder
Pencil 3/8 in.
(10 mm)
1/8 in.
(3.2 mm)
Wood Drill
Screw
driver Hammer
Level 3/8 in.
(10 mm)
Concrete Drill
Drill
W-A
Lag Bolt Concrete Anchor
1a. MOUNT WALL PLATE ON SINGLE STUD
Find the stud by the stud
finder and mark the center.
2
Use wall plate (A) to mark two mounting hole locations.
A
2
Remove covers and save
1
V4
Wall plate

Insert the glass shelf into the slot of the wall plate, then glissade it to the desired location and
fasten the screws on it
Insert the cable manager into the wall bracket, then attach the end caps .
Tighten the screws
C
B
Made in China
PERLE ELECTRONICS HARDWARE (HONGKONG) CO., LIMITED • FLAT B07, 23/F HOVER IND BLDG NO.
26-38 KWAI CHEONG RD •
Any questions please contact : [email protected]
C
B
D
A
Drill pilot holes using a 1/8 in. (3.2 mm)
diameter drill bit. Secure the wall plate with the lag bolt.
A
3 4
Level
1/8 in.
Ø3.2 mm
2.2in. (55mm)
W-A
W-B
1/8”
(3.2mm)
2 3/8”
(60mm)
3/8”
(10mm)
2 3/8”
(60mm)
Drill 2 pilot holes on concrete wall.
Remove covers and save
W-B
A
A
1b. MOUNT WALL PLATE ON CONCRETE WALL
2 3
3. End caps and cable manager installation
2. Tempered glass Installation
Attach the saved covers
Attach the saved covers
Use wall bracket holes to mark 2 mounting
locations.Use level to ensure proper alignment.
Insert 2 concrete anchors into
drilled holes
Secure wall plate to concrete wall using screws with
socket wrench
Please check www.perlesmith.com for more products and company information.