Perlesmith PSTVS18 User manual

Model: PSTVS18
Table Top TV Stand Instruction
Manual
V1.0
Thank you for choosing this PERLESMITH product! At PERLESMITH we
strive to provide you with the best quality products and services in the
industry. Please share your experience of our product with others at
www.perlesmith.com/pages/reviews if you are satisfied. Should you have
any issues, please don't hesitate to contact us.
Technical Support:
1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US)
[email protected] (CA)
Website:
www.perlesmith.com

P1
IMPORTANT SAFETY INFORMATION
Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact
our Technical Support line at 1-800-556-6806 or customer service at
[email protected] (US)/ [email protected] (CA).
CAUTION: Avoid potential personal injuries and property damage!
Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
Check the VESA Pattern of TV before the Installation
Minimum VESA pattern: 200mm/8 in.(W)x100mm/4 in.(H)
If your TV VESA is greater than 600x400 mm/24x16 in. or less than
VESA 200x100mm/8x4in., this TV stand is NOT compatible.
MAX: 600mm/23.6 in.
MAX: 400mm/16 in.
100 mm ≈ 4 in.
200 mm ≈ 7 7/8 in.
400 mm ≈ 15 3/4 in.
600 mm ≈ 23 5/8 in.
Tools Needed (Not lncluded)
Phillips Screwdriver
If this TV stand is NOT compatible, please contact customer service
at [email protected] (US)/ [email protected] (CA)
to find a compatible product.

P2
WARNING: This product contains small items that could be a choking
hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, contact our
Product Support line at 1-800-556-6806 or customer service at
[email protected] (US)/ [email protected] (CA).
• Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware for Step 2
(A) x6
Rubber Foot
Note: The bolt is shown in
accordance with the actual size
(B) x3
M6x25mm Bolt
x1
Lower Support Pillar
02
x1
Plastic Cover
07
x1
Upper Support Pillar
03
x1
Tempered Glass Base
01
(E) x3
M6x12mm
Bolt
Note: The bolt is shown
in accordance with the
actual size
(C) x3
φ6.5xφ16x1.5
Washer
(H) x1
5/32in. (4mm)
Allen Key
(G) x1
Cable Clip
(H) x1
5/32in. (4mm)
Allen Key
(D) x3
φ6.2xφ18x1.5
Plastic Washer

(M-A) x4
M6x16mm
Bolt
(M-B) x4
M6x35mm
Bolt
(M-C) x4
M8x25mm
Bolt
(M-D) x4
M8x50mm
Bolt
(M-E) x4
M8x65mm
Bolt
P3
(M-H) x8
L5mm
Spacer
(M-I) x8
L10mm
Spacer
Note: The bolts and spacers are shown in accordance with the actual size
Supplied Part and Hardware for Step 3
Supplied Parts and Hardware for Step 4
x2
TV Bracket
06
(M-G) x4
D8x18x1.5
Washer
(H) x1
5/32in. (4mm)
Allen Key
(E) x8
M6x12mm
Bolt
Note: The bolt is shown
in accordance with the
actual size
(M-F) x4
Washer
x1
TV Plate
Connector
04
x2
TV Plate
05

Place rubber feet [A] to the tempered glass base [01] in the
corners
Note: Kindly note that the tempered glass base is designed to show the
shiny glass side facing up
Step 1-1
Connect the lower support pillar [02] to tempered glass base [01]
Step 1-2
P4
Secure the lower support pillar [02] to tempered glass base [01] using plastic
cover [07], washers [C], plastic washers [D], bolts [B] and allen key [H].
Note: You may need
assistance with this step.
Supplied Part for Step 5
Step 1 Assemble the Base
A
D
C
B
H
Table
(F) x2
Safety Lock
01
01
07 01
02
02
H

P5
Step 2 Connect the Upper Support Pillar [03] to Lower Support Pillar [02]
Note: There are two choices for height adjustment. You can choose your
desired height position while connecting the TV plates [05] to upper support
pillar [03]
The First Choice
The Second Choice
Step 3 Connect the TV Plates [05] to Upper Support Pillar [03]
E
G
02
03
H

P6
E
04
05
05
E
Please do not firmly tighten the 4pcs
bolts [E] in this step.
Insert the other TV plate into the TV plate connector, then insert the other
4pcs bolts [E] into the TV plate. Finally secure the TV plates to upper
support pillar by tightening the 8pcs bolts [E]
H
H

P7
Too Long
Correct Correct
Too Short
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Please Note: The provided TV bolts meet most of today’s TVs design.
However, some TVs require special bolts which may not be in the hardware
bag. In this case we offer our “PSUHP" Universal Hardware Kit which
provides a large selection of bolts that can meet the demand of older and
unique applications.
Please Note: When using the spacers it is important to note that they can be
used in multi-layers (meaning stacked). If you have any difficulty understand-
ing how to install the TV bolts or spacers, please contact customer service at
[email protected] (US)/ [email protected] (CA).
CAUTION: Ensure the TV brackets
[06] is EQUALLY CENTERED on your
TV and securely fastened in place.
Please note: The bolt hole locations
on your TV may vary in accordance of
the manufacturers design of the TV. We
are only illustrating possible locations
of the bolt holes.
Only one bolt size fits your TV.
Select TV Bolts
Step 4 Secure the TV Brackets [06] to TV
M6 M8
06

P8
Option B (For Round Back TV)
M-F
M-I(If needed)
M-G
M-A/M-C
M-F
M-B/M-D/M-E
M-H/M-I
M-G
Note: Keep
the arrow up
Note: Keep
the arrow up
Option A (For Flat Back TV)
M-G
M-G
The spacers must be used with washers [ M-G ] to stop spacers from falling down.
Alternate Spacer
Setups
The spacers must be used with washers [M-G] to stop spacers from falling down.

P9
Option D
For cable interference or inset holes, use spacers [M-H] and [M-I] to create
extra space between the TV and TV brackets.
The spacers must be used with washers [M-G] to stop spacers from falling down.
Spacers may be necessary for 2 holes ONLY.
The spacers must be used with washers [ M-G ] to stop spacers from falling down.
Option C (For TV with A “Bump”)
M-B/M-
D/M-E
M-H/M-I
M-G
M-F
3
Note: Keep
the arrow up
M-F
M-B/M-D/M-E
M-H/M-I
M-G
M-F
M-A/M-C
3
M-G
M-G
Alternate Spacer
Setups
Alternate Spacer
Setups

①
②
Step 5-1 Hang the TV with brackets to the TV plate
Step 5-2 Push the bottom of the TV to TV plate
Step 5-3 Insert the safety locks [F] into the upward facing hooks at the
midway to lower part of the TV bracket. Please note this is where the lower
part of the TV bracket meets the lower part of TV plate. Then tighten the
bolts of the safety lock [F] until the bolts touch the TV plate.
Step 5 Secure TV to TV Plate and Manage the Wires
TV brackets are three-height-adjustable. You can choose the proper height.
Note: Please note, there is
no bolt holes in the TV plate.
Manage
the wires
The First Choice
The Second Choice
The Third Choice
HEAVY! You may need
assistance with this step.
③
“Be gentle”

If necessary，the TV plate or TV can be swivelled manually.
Step 6 Adjust Swivel Angle of TV Stand