Perlesmith PSLT3 User manual

Installation Instructions V1.0
PSLT3
Thank you for choosing our product! We strive to provide the best
quality and services for our customers. Would you kindly share your
experience on Amazon if you are satisfied? Should you have any
issues, please don't hesitate to contact us.
Telephone：
800-5566-806 Mon-Fri 10am - 6pm (PST) (USA) (CAN)
Email：
[email protected] (US/CA/DE/UK/FR/IT/ES/JP/AU)

level
x2
03 x1
04 x1
07
x1
x1
05
Supplied Parts
Tools Needed (Not lncluded)
Stud Finder Tape measure Pencil Drill
5mm
Wood Drill
10mm
Concrete Drill socket wrench Screw Driver
Hammer
IMPORTANT SAFETY INFORMATION
•Check package contents against Supplied Parts and Hardware Lists to assure that all
components were received undamaged. Do not use damaged or defective parts.lf you
require replacement parts, contact customer service at [email protected]
•Not all parts and hardware included will be used.
•Carefully read all instructions before attempting installation.If you do not understand the
instructions or have any concerns or questions, please contact customer service at
[email protected]
•This product may contain moving parts. Use with caution.
•Do not use this product for any purpose or in any configuration not explicitly specified in
this instruction. We hereby disclaim any liability for injury or damage arising from
incorrect assembly, incorrect mounting, or incorrect use of this product.
•DO NOT INSTALL INTO DRYWALL ALONE.
•Please check www.perlesmith.com for more products and company information.
1
01 x2
02 x2
TV Bracket
TV Bracket
Wall Plate
Template
Wall Plate
Front Rail
Back Rail
Plastic Cover
06

Supplied Hardware
Hardware for Attaching TV Bracket to TV
Washers
M8
x4
A2
x4 x8
Philips Screws
M6X15mm
M6X30mm
x4x4
D1 D2
F1 F2
x4
E1
x4
E2
x4
E3
Philips Screws
M8 x 15mm
M8 x 45mm
M8 x 65mm
C1
x8
C2
Spacers
5mm
Spacers
10mm
B
Hardware for Attaching Wall Plate to Wall
Lag Bolts
M8X65
x4 x4
A1
These anchors are for
concrete or brick walls
ONLY. DO NOT use them
in drywall or wood studs.
CAUTION!
A3
Wall
Anchor
2
Spacer with
M6/M8
M6 Nut X4 ST4.2X10 X4

Step 1 Measure VESA and Check TV screws
Step 2
Check TV screws
When attaching brackets to the flat screen, be
careful not to over tighten screws and be sure that
screws do not bottom out in the mounting holes.
Too Short Too Long
Correct Correct
Hand thread screws into the threaded
inserts on the back of your TV to
determine which screw diameter (M6, or
M8) to use.
Measure the distance between the holes located at the back of your TV
(these measures may form the shape of a square, or a rectangle) and
check that these taken measurements are within the VESA(*) range for
this wall mount.(*)
VESA: International standard established by the TV manufacturers used to
determine if LCD/LED TVs are compatble with wall mounts.
Width
Height
For FLAT TV
Attach the TV Brackets to Your TV
3
200 mm ≈ 7 7/8 in
400 mm ≈ 15 3/4 in
100 mm ≈ 4 in
300 mm ≈ 11 3/4 in
600 mm ≈ 23 6/10 in
Manual Only!
D1/E1
B
05
06
Bottom of TV
Top of TV

4
Step 3
For Flat TV with Inset Holes or Cable Interference or Rounded TV
First, make sure the diameter of the bolt(D1-E3) fits your TV. Then, please see
the diagram above. You will need to thread the bolt into the TV using the washer
(B) and spacer (C1 or C2) if necessary with a screwdriver(Not included). Please
make sure the monitor brackets(05/06) are vertically centered and level with
each other.
Assemble Wallplate
3-1
Manual Only!
B
D2/E2/E3
C1/C2
DO NOT overtighten.
Tighten only until snug.
Top of TV
Bottom of TV
05
06
F1
01
04
02

5
Step 4
Step 4A
X
For wood stud installation, follow STEP 4A
For concrete installation, follow STEP 4B
Attach Wall Plate to Wall
Wood Stud Option
WARNING:
WARNING:
Ensure the wall plate is securely fastened to the wall
before continuing on to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum
1½ x 3½ in. (38 x 89 mm)
● Stud center must be verified
WARNING:
Avoid potential personal injury or property damage! DO NOT
over-tighten the lag bolts [A1]. Tighten the lag bolts [A1] only until the
washers [A2] are pulled firmly against the wall plate.
F2
3-2
Manual Only!
03
03

6
4A-1
Use a stud finder(not
included) to locate wood
studs. Mark the edge and
center locations.
4A-2
4A-3
ø5mm
65mm
Position the template at
your desired height and
line up the holes with your
stud center line. Level the
template and mark the
holes.
Drill 4 pilot holes using a
5 mm diameter drill bit.
Make sure the depth is
not less than 65mm.
07

7
4A-4
Install the wall plate using lag bolts [A1] and washer [A2]. Tighten
the lag bolts [A1] only until the washers [A2] are pulled firmly
against the wall plate.
Step 4B
Avoid potential personal injury or property damage! DO NOT
over-tighten the lag bolts [A1]. Tighten the lag bolts [A2] only until the
washers [A2] are pulled firmly against the wall plate
.
WARNING:
Wall
Anchor
A3
WARNING:
Ensure the wall plate is securely fastened to the wall
before continuing on to the next step.
WARNING:
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Mount the wall plate directly onto the concrete surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
Solid Concrete or Concrete Block Option
A1 A2

4B-1 4B-2
ø10mm
70mm
Position the template at your desired
height, level the template and mark
the pilot hole locations.
Drill 4 pilot holes using a 10mm
diameter drill bit. Make sure the
depth is not less than 70mm Never
drill into the mortar between blocks.
8
4B-3
Use the hammer to
knock anchors [A3]
into the wall.
A1
A2 A3
Install wall plate using lag bolts [A1], washers [A2] and anchors
[A3]. Be sure the anchors [A3] are seated flush with the concrete
surface. Tighten the lag bolts [A1] only until the washers [A2] are
pulled firmly against the wall plate. DO NOT over-tighten the lag
bolts [A1].
07

Step 5
9
Hang Your TV to the Wall Plate
Adjustment 1
Level
HEAVY! You may
need assistance
with this step.

10
Tilt Angle Adjustment
Remove
Your TV should adjust easily when moved, then stay in place. If your
TV is too loose or too tight, adjust side tension knob [T] .
NOTE: Once your TV is in place, tighten the side tension knob [T] to
prevent unwanted movement.
T
HEAVY! You may need assistance with this step.
Adjustment 2
Adjustment 3

Thank you for choosing our product! We strive to provide the
best quality and services for our customers. Would you kindly
share your experience on Amazon if you are satisfied? Should
you have any issues, please don't hesitate to contact us.
Telephone：
800-5566-806 Mon-Fri 10am - 6pm (PST) (USA) (CAN)
Email：
[email protected] (US/CA/DE/UK/FR/IT/ES/JP/AU)