Perlesmith PSLFK1-24 User manual

V5.0
LARGE FULL-MOTION TV WALL MOUNT
[email protected]
PSLFK1-24

*
*
*
*
*
*
Stud Finder Tape Measure Pencil Drill
1/2 in. (12.7 mm)
7/32 in. (5.5 mm)
Wood Drill
Screw Driver Hammer
WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER
INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.
If you do not understand the instructions or have any concerns or questions, please contact a qualified
installer.
Do not install or assemble if the product or hardware is damaged or missing. Not all parts and hardware
included must be used. If you require replacement parts, contact customer service at
[email protected].
This product has been designed for use on a vertical wall constructed of wood studs. Wood studs being
defined as a wall consisting of a minimum of 2” x 4” studs with a maximum of 24” stud spacing with a
maximum of 1/2” of wall covering (drywall, lath, plaster).For custom installations please contact a
qualified installer. For safe installation, the wall you are mounting to must support 4 times the weight of
the total load. If not, the surface must be reinforced to meet this standard. The installer is responsible for
verifying that the wall structure/surface will safely support the total load.
This product may contain moving parts. Use with caution.
DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY FOR THIS PRODUCT.
CAUTION!MAXIMUM WEIGHT CAPACITY
!132 lbs
(60kgs)
USE WITH PRODUCTS LARGER THAN THE MAXIMUM WEIGHT AND SIZE MAY RESULT IN
INSTABILITY CAUSING POSSIBLE INJURY. USER MUST REMOVE TELEVISION OR OBJECT
OFF THE BRACKET BEFORE ADJUSTING. NOT SUITABLE FOR A TV THAT SURPASSES THE
TELEVISION MAXIMUM WEIGHT CAPACITY AND RECOMMENDED DIAGONAL MEASURED TV
SIZE!
WARNING!
Tools Needed (Not Included)
Socket Wrench
Weight Capacity

TV Bracket
Arm Extensions 03 x2
Wall Extension A
05 x2
Wall Extension B
06 x2
04 x2
Front Support 02 x1
5/16 x 2½ in
Lag Bolts
x4
A
Washers
Ø8mm
x4
B
M8
Nuts
x8
C
Washers
Ø8mm
x8
D
Philips Screws
M6 x 15mm
M6 x 30mm
Philips Screws
M4 x 12mm
M4 x 30mm
Washers
Ø6mm
M4-5-6
Spacers
L10mm
x4
x4 x4
x4
Philips Screws
M8 x 15mm
M8 x 45mm
x4
x4 x8 x4
M-EM-A M-B M-C M-D M-F M-G M-H
Spacers
L5mm
x8
M-I
Arm and
Wall Plate 01 x1
E
x1
Allen
Wrench
Supplied Hardware

Step 1 Before TV Bracket Installation
75 mm ≈2 7/8 in
100 mm ≈4 in
200 mm ≈7 7/8 in
300 mm ≈11 3/4 in
400 mm ≈15 3/4 in
600 mm ≈23 5/8 in
400mm (15 3/4 in)
Max 600mm（23 5/8 in）
Max
Measure the distance between the holes located
at the back of your TV (these measures may form
the shape of a square, or a rectangle) and check
that these taken measures are within the VESA(*)
range for this wall mount.
(*) VESA: International standard established by the
TV manufacturers used to determine if LCD / LED
TVs are compatible with wall mounts.
Check TV Screws
Please select the proper screw length for your
TV by hand tightening to check your plat panel
thread depth.
TV

M-H
M-CM-A
04
M-E
04
04
M-H
M-I
M-G
M-D
M-B
04
M-F
M-I
M-G
04
04
For Flat Screen TV
For Curved TV
Step 2 Install TV Bracket
or
or

C
D
05
06
01
05
05
06
06
01
Extension B
Extension A
The wall plate extensions can be moved
0.6”for both side if necessary.
0.6in
0.6in
0.6in
0.6in
Only one side need to attach each of
extensions A and B.
for 18”to 24”space studs
for studs with the sapce between 16.5”to 18”
Step 3 Attach the Extensions to the Wall Plate

Use a stud finder (not included) to locate wood
studs. Mark the edge and center locations.
16in to 24in
Step 4A
4-1
4-2 Use wall plate to mark mounting location x4
locations for 24”space studs.
01
01
left
right
Mark the 4 inside holes for
18”space studs.
Holes pattern for
16.5”to 18”space
studs.
Ensure marking at the
center of the stud.

Drill 4 pilot holes using a 7/32 in. (5.5 mm) diameter drill
bit. Make sure the depth is not less than 2 3/4” (70mm).
7/32 in.
Ø5.5 mm
in. (70 mm)
01
Mount wall plate using 4 sets of 5/16 lag bolts (a) and washers
B with a 1/2 in. socket wrench (not included).
A
A
B
2
B
UP
01
left
right
Secure the lag bolts to 4 inside holes
for 18”space studs.
Secure the lag bolts to 4 inside holes for 16.5”to 18”space studs.
Secure the lag bolts to pilot holes for
24”space studs.
4-4
4-3
1/2 in. (12.7 mm)
socket wrench

S1
S2
01
02
03
S4
Insert the extensions into the .
03 02
5-2
5-1
02
03
5-3
Fasten the Screws x4 removed from
extensions .
S4
S4
5-4
S1 S2
Hang 02 and 03 onto 01, and using Screwdriver secure with
pre-assembled screws and washer .
03
03
S4
S4
S2
S1
Step 5 Install Arm Extensions then Fasten It
Remove the pre-assembed screws
from the extensions and save them
to use.

Secure TV with brackets
against the arm
extensions and
with the pre-assembled
screws [S3] .
04
S3
03 02
Hang TV with brackets
04
onto the
arm extensions
02
and
03
.
04
03
04
02
Screw
driver [S3]
04
Step 6 Hang TV
Step 7 Secure TV

If needed, the TV can be leveled +/-3 degrees.
Loosen 2 screws [S1]
S1 Level the TV
To adjust the tilt in both sides, loosen
both tilt levers and move panel to
desired position. Tighten both tilt levers
to hold desired tilt.
！
TIGHTEN
！
LOOSEN
E
E
Step 8 Tilt Adjustment
Step 9 Level Adjustment
Tighten 2 screws S1
± 3°

Thank you for choosing our product! We strive to provide the
best quality and services for our customers. Would you kindly
share your experience on Amazon if you are satisfied? Should
you have any issues, please don't hesitate to contact us.
Telephone：[phone]
Mon-Fri 10am - 6pm (PST) (USA)
Email：[email protected]
(US/CA/DE/UK/FR/IT/ES/JP/AU)