Perlesmith PSXLF02 User manual

©
Tilt Adjustment I
1. Slightly loosen the two tilting nuts [T].
2. Adjust TV to your desired tilt angle.
-,
\
A.CAUTION!
DO NOT over-loosen these two nuts
when adjusting the
tilt angle to prevent
the
TV from falling off.
\ \ \ \ \ \
\ \
\ \I
'I
I
I
I
I
'
I
I
I
'
7/16" (11mm)
3. Retighten two tilting nuts [T] to fix the tilt angle. Socket Wrench
(Not Included)
~
~
~
~
~
~
~
~
~
=
=
=
=
=
=
~
860-00042-01 Rev0O
15
',
A~
"Q/
PI;;:RLI;;:~MITI--I
Full Motion TV Wall Mount
Instruction Manual Rev01(B)
l~ I
Model: PSXLF02
Thank you for choosing this PERLESMITH product! At PERLESMITH we strive to
provide you with the best quality products and services in the industry. Should you
have any issues, please
don't hesitate to contact us at
Technical Support:
(US/ CA) 1-800-556-6806 Mon-Fri 8am -8pm (CST)
(UK)
44-808-196-3891 Mon-Fri 2pm - 10pm (UTC)
Other Info: [email protected]
Website: www.perlesmith.com

Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact
our customer service
at [email protected].
A.CAUTION: Avoid potential personal injuries and property damage!
•
Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity.
We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate
use.
• This product is designed for use in wood stud, solid concrete, and concrete
block walls -
DO NOT install into drywall alone.
• The wall must
be capable of supporting five times the weight of the TV and
mount combined.
If your TV weighs more, this
mount is NOT compatible.
~
DO NOT exceed the maximum weight
indicated. This mounting system
is intended
for use only with the maximum weights
indicated.
Use with products heavier than the
maximum weights indicated may result
in
failure of the mount and its accessories,
causing possible damage and or injury.
100mm;:::: 3.9"
200mm;:::: 7.9"
300mm
;:::: 11.8"
400mm
;:::: 15.7"
600mm
;:::: 23.6"
800mm
;:::: 31.5"
Minimum VESA pattern:
200mm / 7.9" (W) x 100mm / 3.9" (H)
If your TV VESA is greater than 800 x 600mm / 31.5 x 23.6" or less
than
VESA 200 x 100mm / 7.9 x 3.9", this mount is NOT compatible.
01
"
(
rC\
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
,
'
,
'
'
'
'
I
I
I
I
\\ '{
,
'\
A CAUTION!
DO NOT over-loosen these two bolts
when adjusting the level angle to
prevent the
TV from falling off.
I
__ _ J..
--
'
,,
Level Adjustment
If needed, the TV can be levelled.
1. Slightly loosen the two bolts [S1]
on the rear of the front
support.
2. Level your TV.
3. Retighten both bolts [S1) to hold TV in place.
14
~
Phillips
Screwdriver
(Not Included)
'
7/16" (11mm)
Socket Wrench
(Not Included)

Before attempting to hang the TV, make sure the locking tabs are positioned
towards
the bottom of the TV. Hang the TV with brackets [03] onto the front
support [02].
Make sure that the upper and lower hooks on the TV brackets are
over the front support bars.
·'·
I
'!'=li'!:iii~~
,,
I
I
I
I
\
& ~assistance with this step.
= L/-/,
I
I
I
I
I
I
I
I
I
I
I
,. ... --
/
,,,'
-----------,,,,
,/
,
,
\
I
I
\
\I
I
I
I
I
I
I
J
I
J
I
I
I
I
Position the locking tabs towards the top of the TV and secure the locking tabs in
place using the bolts [S2] removed from Step 1. Firmly tighten the bolts [S2].
§~-:;;;'.,,$,_,
i '\
I
' ' '
',
' ' -
--- M
-- ---- r
',,,,,' ',,
, '
, \
, \
I \
I \
I I
I \
I
~
Phillips
Screwdriver
(Not Included)
,
13
I
I
,
,
I
I
I
I
I
I
I
I
I
I
\ '~
I \ I
I
J
I
cl
Tape
Measure Pencil Phillips
Screwdriver
7/16" (11mm)
Socket Wrench
If
you are not sure of the
wall construction, please
contact our customer
service at
[email protected].
1/2" (13mm)
Socket Wrench Drill
Tools Needed
for Wood Stud Installation Tools Needed for Concrete Wall Installation
~OR ✓ : /
/
~
Stud Finder Awl
ooa D B 0
OTO D B Hammer
Supplied Parts and Hardware
A. WARNING: This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly,
verify all parts are included and undamaged. Do not use
damaged or defective parts. If you require replacement parts, contact our
customer service at [email protected].
• PLEASE NOTE:
Not all hardware included in this package will be used.
I '
~
c ,J
~Ii ii
'
( )
Im) Washer
Iii
Spacers [if needed]
® 0 8 e
M6/ MS
[E1] x 8 [E2] x 4 [E3] x 4
[B] x 4 L2.5mm L10mm L22mm
02

lml TV Bolts [Only one bolt size fits your TV]
!_NOTE: The bolts_ are_shown_ in_ actual size._ 7
M6 x 15mm
[C1] x 4
~
MB x 15mm
[01] X 4
MB x 35mm
[03) X 4
M6
MS
M6 x 35mm
[C2] x 4
MB x 25mm
[02) X 4
MB x 50mm
[04) X 4
Ci
~ f -? = 2: ~~~ --- "c p ~=r l
~ ~ = == - -~
Arm Assembly / Wall Plate
lmllx1
03
Wall Plate Template
ml X 1
11 ~ 11
Level
mJ X 1
I
I
I
I
I
I
I
I
I
I
I
I
I
Secure the front support [02] to arm assembly / wall plate [01] using the
preassembled bolts [S1] removed from Step
4-4 .
,-----------------------------------------~
: NOTE: Make sure the big button in the front support [02] :
: fits into the groove
on the arm assembly. '
,-- -- ...
, '
I '
I ' ' \'
\
'
~
, --"-"-=--- ---
,,,., - -- ........
I \
I \
I \
I \
I
--- - --~
\
\,',,,_
',, _______ _ ______________ _
7/16" (11mm) Phillips
Screwdriver
(Not Included)
Socket Wrench
(Not Included)
12
',
''''\ \ I
I
I
I
I
I
I
I
I

Remove the pre-assembled bolts [SJ from the front support [02J and keep
them for the use in Step
4-3 .
-- ------ - ---- - -- - -- --- -- - ---- - -- - --- - --- - -- --- ------- ------ ----------
Insert the end caps [04J to the end of front support [02J.
Tighten the bolts
[SJ removed from Step 4-1 to secure.
~
Phillips
Screwdriver
(Not Included)
~
Phillips
Screwdriver
(Not Included)
Remove the preassembled bolts [S1 Jform the front support [02J and keep them for
the use in Step 4-5.
~
Phillips
Screwdriver
(Not Included)
~
7/16" (11mm)
Socket Wrench
(Not Included)
• , 11',.----',-- S1
11
- --------- --- ---- --- ---------- -- --- -- --- -- -- --- --- ---- - ----------- - -- · -----.
! NOTE: The lag screw is shown in actual size. !
' '
I •• • ••• ••• • •••• •••••• • • • ••-- -• • ••••• ••- -- •• - -- • • •• •• • • • •••• •• • - - •• ••••• ••'
~ Lag Screw
~ X G ST5/16 x 2-3/4"
_ACAUTION! I
This anchor is for !
f»x6
Wall
Anchor
concrete or brick walls .++ (Q
ONLY. DO NOT use them i
_ __ in_ drywall_ or wood_ studs. ____ j
=t ~ :
Front Support W X1
Remove the pre-assembled Bolts [S2] from the
brackets using a Phillips screwdriver. Save the
Bolts
[S2J for use in Step 5-2.
Select TV Bolts
Only one size bolt fits your TV .
M6 MB
Ii
0 0
(f!f_
~
End Cap ml x2
~
(±) ~
Phillips Screwdriver
(Not Included)
NOTE: Please do not over tighten the TV bolts to avoid damaging your TV.
Bolt length: Verify adequate thread engagement with bolts or bolts / spacers
combination.
We recommend thread engagement by at least 5 turns.
-Too short will not hold the
TV.
-Too long will damage the TV .
04

Too Short
-, 11 •®
~ Too Long
LJ!J@
ffigect
Correct
., ,. g
PLEASE NOTE: The provided TV bolts meet most of today's TVs design. However, some
TVs require special bolts which may not be in the hardware bag. In this case we offer our
"
PSUHP " Universal Hardware Kit which provides a large selection of bolts that can meet
the demand
of older and unique applications.
PLEASE NOTE: When using the spacers it is important to note that they can be used in
multi-layers (meaning stacked). If you have any difficulty understanding how to install the
TV bolts or spacers, please contact customer service at [email protected]
I _"u,c I
Option A (For Flat Back TV)
'
'
~
~
~
' •
'
C,
-- - -- ------------------'
Option B (For Round Back TV)
·~ '
: F C2 I D2 I D3 I D4 1:
I I
I I
I I
I I
: ~ :
I ~ ~ I
~
Alternate Spacer Setups
; e-GE 1/ E2 / E3 i
I I
I I
I .l,
'------------------------'
ee~e~~~
05
10

.,,.-/
~·
-0
X
X
nT
0
x2
Position the wall plate template [05] at
your desired height. Level the wall
plate template and mark the pilot hole
locations.
Drill 6 pilot holes using a
3/8"( 10mm)
diameter drill bit. Make sure the depth
is not less than 3"(75mm). Never drill
into the mortar between blocks.
~
~
Electric Drill
(Not Included)
3"(75mm)
[~!
09
Use the hammer to knock anchors [A2]
into the wall.
Be sure the anchors [A2]
are seated flush with the concrete or
brick surface.
~
Hammer
(NOT Included)
Install arm assembly / wall plate using
lag screws [A1]. Tighten the lag screws
[A1] only until they are pulled firmly
against the wall plate.
DO NOT
over-tighten the lag screws [A1].
HEAVY! You may
~ need assistance
with this step. '
1/2"(13mm)
Socket Wrench
(Not included)
t
~ I
Option C (For TV with A "Bump")
--------------------------,
i-: C~ I D2 / D3 / D4 1 [_ _____ ........ _j
- , I ) I
I '' ' - -I --,
: ':, ~
I 1 • 1
:;~~~~~~ ®@
Option D
--- - --~
~ :
' '
,l ffll!l ol :
~ :
• 0 (if needed) ----,
: ____ ~-------------- ___ :
For cable interference or inset holes, use spacers [07] to create extra space
between the
TV and TV brackets.
------L-- ----
''
''
''
'I
''
''
''
''
''
''
''
''
''
''
''
''
I ' - - - -
Alternate Spacer Setups
ae,=~~8~9
06
\
I I.
m E1 1 E2 1 E3
1
I
t~~g!/
. ·t- L:-
mlfil :
I
- - ----"
®@

A WARNING:
• Avoid potential personal injury or property damage! DO NOT over-tighten
the lag screws [A 1]. Tighten the lag screws [A 1] only until they are pulled firmly
against the wall plate.
e DO NOT USE ANCHOR [A2] FOR THIS STEP! *
• Ensure the arm assembly/ wall plate [01] is securely fastened to
the wall before continuing to the next step.
• Any material covering the wall must
not exceed 5/8" (16mm).
• Nominal wood stud size: common 2 x
4" (51 x 102mm) minimum
1½ x
3½" (38 x 89mm).
• Stud center
must be verified.
~
.
~
I
I
I
:~9rnrn J :
; 16 •( 40~ .
.:::::.__ -ml---.
-,
·,
..,, --l!
_____->~ ~-
07
Use a stud finder (not included) to
locate wood studs or use an awl
(not included) to verify the edges.
Mark the edge and center locations.
~88)
Stud Finder
(Not Included)
~
Awl
(Not Included)
Position the wall plate template
[05] at your desired height and
line up the holes with your stud
center line. Level the wall plate
template
[05] and mark the
holes.
)·
Drill 4 pilot holes using a
7
/32" (5.5mm) diameter drill
bit. Make sure the depth is
not
less than 2 3/ 4" (70mm).
Electric Drill
(Not Included)
2 374"{70mm)
~f
7 /32 " (5.5mm)
Install the arm assembly / wall plate
[01] using lag screws [A 1]. Tighten
the lag screws [A1] only until they are
pulled firmly against the wall plate.
®
'
W
You may need
& assistance with
th is step.
A WARNING:
• Avoid potential personal injury or property damage! DO NOT over-tighten the lag
screws [A 1 ]. Tighten the lag screws [A 1] only until they are pulled firmly against the wall
plate.
•
Ensure the arm assembly / wall plate (01] is securely fastened to
the
wall before continuing to the next step.
• Any material covering the wall must not exceed 5/8 " (16mm).
• Mount the wall plate directly onto the concrete surface.
•
Minimum solid concrete thickness: 8" (203mm) .
•
Minimum concrete block size : 8 x 8 x 16" (203 x 203 x 406mm) .
•
Never drill into the mortar between blocks.
08
Wall
Anchor
fD

A WARNING:
• Avoid potential personal injury or property damage! DO NOT over-tighten
the lag screws [A 1]. Tighten the lag screws [A 1] only until they are pulled firmly
against the wall plate.
e DO NOT USE ANCHOR [A2] FOR THIS STEP! *
• Ensure the arm assembly/ wall plate [01] is securely fastened to
the wall before continuing to the next step.
• Any material covering the wall must
not exceed 5/8" (16mm).
• Nominal wood stud size: common 2 x
4" (51 x 102mm) minimum
1½ x
3½" (38 x 89mm).
• Stud center
must be verified.
~
.
~
I
I
I
:~9rnrn J :
; 16 •( 40~ .
.:::::.__ -ml---.
-,
·,
..,, --l!
_____->~ ~-
07
Use a stud finder (not included) to
locate wood studs or use an awl
(not included) to verify the edges.
Mark the edge and center locations.
~88)
Stud Finder
(Not Included)
~
Awl
(Not Included)
Position the wall plate template
[05] at your desired height and
line up the holes with your stud
center line. Level the wall plate
template
[05] and mark the
holes.
)·
Drill 4 pilot holes using a
7
/32" (5.5mm) diameter drill
bit. Make sure the depth is
not
less than 2 3/ 4" (70mm).
Electric Drill
(Not Included)
2 374"{70mm)
~f
7 /32 " (5.5mm)
Install the arm assembly / wall plate
[01] using lag screws [A 1]. Tighten
the lag screws [A1] only until they are
pulled firmly against the wall plate.
®
'
W
You may need
& assistance with
th is step.
A WARNING:
• Avoid potential personal injury or property damage! DO NOT over-tighten the lag
screws [A 1 ]. Tighten the lag screws [A 1] only until they are pulled firmly against the wall
plate.
•
Ensure the arm assembly / wall plate (01] is securely fastened to
the
wall before continuing to the next step.
• Any material covering the wall must not exceed 5/8 " (16mm).
• Mount the wall plate directly onto the concrete surface.
•
Minimum solid concrete thickness: 8" (203mm) .
•
Minimum concrete block size : 8 x 8 x 16" (203 x 203 x 406mm) .
•
Never drill into the mortar between blocks.
08
Wall
Anchor
fD

.,,.-/
~·
-0
X
X
nT
0
x2
Position the wall plate template [05] at
your desired height. Level the wall
plate template and mark the pilot hole
locations.
Drill 6 pilot holes using a
3/8"( 10mm)
diameter drill bit. Make sure the depth
is not less than 3"(75mm). Never drill
into the mortar between blocks.
~
~
Electric Drill
(Not Included)
3"(75mm)
[~!
09
Use the hammer to knock anchors [A2]
into the wall.
Be sure the anchors [A2]
are seated flush with the concrete or
brick surface.
~
Hammer
(NOT Included)
Install arm assembly / wall plate using
lag screws [A1]. Tighten the lag screws
[A1] only until they are pulled firmly
against the wall plate.
DO NOT
over-tighten the lag screws [A1].
HEAVY! You may
~ need assistance
with this step. '
1/2"(13mm)
Socket Wrench
(Not included)
t
~ I
Option C (For TV with A "Bump")
--------------------------,
i-: C~ I D2 / D3 / D4 1 [_ _____ ........ _j
- , I ) I
I '' ' - -I --,
: ':, ~
I 1 • 1
:;~~~~~~ ®@
Option D
--- - --~
~ :
' '
,l ffll!l ol :
~ :
• 0 (if needed) ----,
: ____ ~-------------- ___ :
For cable interference or inset holes, use spacers [07] to create extra space
between the
TV and TV brackets.
------L-- ----
''
''
''
'I
''
''
''
''
''
''
''
''
''
''
''
''
I ' - - - -
Alternate Spacer Setups
ae,=~~8~9
06
\
I I.
m E1 1 E2 1 E3
1
I
t~~g!/
. ·t- L:-
mlfil :
I
- - ----"
®@

Too Short
-, 11 •®
~ Too Long
LJ!J@
ffigect
Correct
., ,. g
PLEASE NOTE: The provided TV bolts meet most of today's TVs design. However, some
TVs require special bolts which may not be in the hardware bag. In this case we offer our
"
PSUHP " Universal Hardware Kit which provides a large selection of bolts that can meet
the demand
of older and unique applications.
PLEASE NOTE: When using the spacers it is important to note that they can be used in
multi-layers (meaning stacked). If you have any difficulty understanding how to install the
TV bolts or spacers, please contact customer service at [email protected]
I _"u,c I
Option A (For Flat Back TV)
'
'
~
~
~
' •
'
C,
-- - -- ------------------'
Option B (For Round Back TV)
·~ '
: F C2 I D2 I D3 I D4 1:
I I
I I
I I
I I
: ~ :
I ~ ~ I
~
Alternate Spacer Setups
; e-GE 1/ E2 / E3 i
I I
I I
I .l,
'------------------------'
ee~e~~~
05
10

Remove the pre-assembled bolts [SJ from the front support [02J and keep
them for the use in Step
4-3 .
-- ------ - ---- - -- - -- --- -- - ---- - -- - --- - --- - -- --- ------- ------ ----------
Insert the end caps [04J to the end of front support [02J.
Tighten the bolts
[SJ removed from Step 4-1 to secure.
~
Phillips
Screwdriver
(Not Included)
~
Phillips
Screwdriver
(Not Included)
Remove the preassembled bolts [S1 Jform the front support [02J and keep them for
the use in Step 4-5.
~
Phillips
Screwdriver
(Not Included)
~
7/16" (11mm)
Socket Wrench
(Not Included)
• , 11',.----',-- S1
11
- --------- --- ---- --- ---------- -- --- -- --- -- -- --- --- ---- - ----------- - -- · -----.
! NOTE: The lag screw is shown in actual size. !
' '
I •• • ••• ••• • •••• •••••• • • • ••-- -• • ••••• ••- -- •• - -- • • •• •• • • • •••• •• • - - •• ••••• ••'
~ Lag Screw
~ X G ST5/16 x 2-3/4"
_ACAUTION! I
This anchor is for !
f»x6
Wall
Anchor
concrete or brick walls .++ (Q
ONLY. DO NOT use them i
_ __ in_ drywall_ or wood_ studs. ____ j
=t ~ :
Front Support W X1
Remove the pre-assembled Bolts [S2] from the
brackets using a Phillips screwdriver. Save the
Bolts
[S2J for use in Step 5-2.
Select TV Bolts
Only one size bolt fits your TV .
M6 MB
Ii
0 0
(f!f_
~
End Cap ml x2
~
(±) ~
Phillips Screwdriver
(Not Included)
NOTE: Please do not over tighten the TV bolts to avoid damaging your TV.
Bolt length: Verify adequate thread engagement with bolts or bolts / spacers
combination.
We recommend thread engagement by at least 5 turns.
-Too short will not hold the
TV.
-Too long will damage the TV .
04

lml TV Bolts [Only one bolt size fits your TV]
!_NOTE: The bolts_ are_shown_ in_ actual size._ 7
M6 x 15mm
[C1] x 4
~
MB x 15mm
[01] X 4
MB x 35mm
[03) X 4
M6
MS
M6 x 35mm
[C2] x 4
MB x 25mm
[02) X 4
MB x 50mm
[04) X 4
Ci
~ f -? = 2: ~~~ --- "c p ~=r l
~ ~ = == - -~
Arm Assembly / Wall Plate
lmllx1
03
Wall Plate Template
ml X 1
11 ~ 11
Level
mJ X 1
I
I
I
I
I
I
I
I
I
I
I
I
I
Secure the front support [02] to arm assembly / wall plate [01] using the
preassembled bolts [S1] removed from Step
4-4 .
,-----------------------------------------~
: NOTE: Make sure the big button in the front support [02] :
: fits into the groove
on the arm assembly. '
,-- -- ...
, '
I '
I ' ' \'
\
'
~
, --"-"-=--- ---
,,,., - -- ........
I \
I \
I \
I \
I
--- - --~
\
\,',,,_
',, _______ _ ______________ _
7/16" (11mm) Phillips
Screwdriver
(Not Included)
Socket Wrench
(Not Included)
12
',
''''\ \ I
I
I
I
I
I
I
I
I

Before attempting to hang the TV, make sure the locking tabs are positioned
towards
the bottom of the TV. Hang the TV with brackets [03] onto the front
support [02].
Make sure that the upper and lower hooks on the TV brackets are
over the front support bars.
·'·
I
'!'=li'!:iii~~
,,
I
I
I
I
\
& ~assistance with this step.
= L/-/,
I
I
I
I
I
I
I
I
I
I
I
,. ... --
/
,,,'
-----------,,,,
,/
,
,
\
I
I
\
\I
I
I
I
I
I
I
J
I
J
I
I
I
I
Position the locking tabs towards the top of the TV and secure the locking tabs in
place using the bolts [S2] removed from Step 1. Firmly tighten the bolts [S2].
§~-:;;;'.,,$,_,
i '\
I
' ' '
',
' ' -
--- M
-- ---- r
',,,,,' ',,
, '
, \
, \
I \
I \
I I
I \
I
~
Phillips
Screwdriver
(Not Included)
,
13
I
I
,
,
I
I
I
I
I
I
I
I
I
I
\ '~
I \ I
I
J
I
cl
Tape
Measure Pencil Phillips
Screwdriver
7/16" (11mm)
Socket Wrench
If
you are not sure of the
wall construction, please
contact our customer
service at
[email protected].
1/2" (13mm)
Socket Wrench Drill
Tools Needed
for Wood Stud Installation Tools Needed for Concrete Wall Installation
~OR ✓ : /
/
~
Stud Finder Awl
ooa D B 0
OTO D B Hammer
Supplied Parts and Hardware
A. WARNING: This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly,
verify all parts are included and undamaged. Do not use
damaged or defective parts. If you require replacement parts, contact our
customer service at [email protected].
• PLEASE NOTE:
Not all hardware included in this package will be used.
I '
~
c ,J
~Ii ii
'
( )
Im) Washer
Iii
Spacers [if needed]
® 0 8 e
M6/ MS
[E1] x 8 [E2] x 4 [E3] x 4
[B] x 4 L2.5mm L10mm L22mm
02

Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact
our customer service
at [email protected].
A.CAUTION: Avoid potential personal injuries and property damage!
•
Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity.
We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate
use.
• This product is designed for use in wood stud, solid concrete, and concrete
block walls -
DO NOT install into drywall alone.
• The wall must
be capable of supporting five times the weight of the TV and
mount combined.
If your TV weighs more, this
mount is NOT compatible.
~
DO NOT exceed the maximum weight
indicated. This mounting system
is intended
for use only with the maximum weights
indicated.
Use with products heavier than the
maximum weights indicated may result
in
failure of the mount and its accessories,
causing possible damage and or injury.
100mm;:::: 3.9"
200mm;:::: 7.9"
300mm
;:::: 11.8"
400mm
;:::: 15.7"
600mm
;:::: 23.6"
800mm
;:::: 31.5"
Minimum VESA pattern:
200mm / 7.9" (W) x 100mm / 3.9" (H)
If your TV VESA is greater than 800 x 600mm / 31.5 x 23.6" or less
than
VESA 200 x 100mm / 7.9 x 3.9", this mount is NOT compatible.
01
"
(
rC\
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
,
'
,
'
'
'
'
I
I
I
I
\\ '{
,
'\
A CAUTION!
DO NOT over-loosen these two bolts
when adjusting the level angle to
prevent the
TV from falling off.
I
__ _ J..
--
'
,,
Level Adjustment
If needed, the TV can be levelled.
1. Slightly loosen the two bolts [S1]
on the rear of the front
support.
2. Level your TV.
3. Retighten both bolts [S1) to hold TV in place.
14
~
Phillips
Screwdriver
(Not Included)
'
7/16" (11mm)
Socket Wrench
(Not Included)

©
Tilt Adjustment I
1. Slightly loosen the two tilting nuts [T].
2. Adjust TV to your desired tilt angle.
-,
\
A.CAUTION!
DO NOT over-loosen these two nuts
when adjusting the
tilt angle to prevent
the
TV from falling off.
\ \ \ \ \ \
\ \
\ \I
'I
I
I
I
I
'
I
I
I
'
7/16" (11mm)
3. Retighten two tilting nuts [T] to fix the tilt angle. Socket Wrench
(Not Included)
~
~
~
~
~
~
~
~
~
=
=
=
=
=
=
~
860-00042-01 Rev0O
15
',
A~
"Q/
PI;;:RLI;;:~MITI--I
Full Motion TV Wall Mount
Instruction Manual Rev01(B)
l~ I
Model: PSXLF02
Thank you for choosing this PERLESMITH product! At PERLESMITH we strive to
provide you with the best quality products and services in the industry. Should you
have any issues, please
don't hesitate to contact us at
Technical Support:
(US/ CA) 1-800-556-6806 Mon-Fri 8am -8pm (CST)
(UK)
44-808-196-3891 Mon-Fri 2pm - 10pm (UTC)
Other Info: [email protected]
Website: www.perlesmith.com