Perlesmith PSLF7 User manual

Thank you for choosing this Perlesmith product! At Perlesmith we strive
to provide you with the best quality products and services in the industry.
Please share your experience of our product with others at
www.perlesmith.com/pages/reviews if you are satisfied. Should you have
any issues, please don't hesitate to contact us.
Technical Support:
1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA/DE/UK/FR/IT/ES/AU)
Website:
www.perlesmith.com
Full Motion Mount Instruction
Manual V1.0
Model: PSLF7

Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact
our Technical Support line at 1-800-556-6806 or customer service at
[email protected]
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud, solid concrete, and concrete
block walls - DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and
mount combined.
Weight Restrictions
IMPORTANT SAFETY INFORMATION
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only with
the maximum weights indicated. Use with products
heavier than the maximum weights indicated may
result in failure of the mount and its accessories,
causing possible damage and or injury.
WARNING
132 lbs.
(60 kg)
If your TV weighs more, this
mount is NOT compatible.
Minimum VESA pattern:
200mm/8 in.(W)x100mm/4 in.(H)
200 mm ≈ 7 7/8 in.
400 mm ≈ 15 3/4 in.
100 mm ≈ 4 in.
300 mm ≈ 11 3/4 in.
600 mm ≈ 23 6/10 in.
MAX:600mm/24 in.
MAX:400mm/16 in.
Check the VESA Pattern of Your TV before the Installation
If your TV VESA is greater than 600x400 mm/24x16 in. or less than VESA
200x100mm/8x4in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
01

Awl
Solid Concrete
or Concrete Block
CAUTION
DO NOT
install into
drywall alone Wood Studs
(with Drywall)
Tools Needed (Not lncluded)
Stud Finder Tape Measure Pencil Drill
7/32 in.(5.5mm)
Wood Drill
3/8 in.(10mm)
Concrete Drill
3/8 in.(10mm )
Socket Wrench
1/2 in.(13mm )
Socket Wrench Screwdriver
Hammer
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware
Verify Your Wall Construction
If you are not sure the wall
construction, please
contact our product
support line at
1-800-556-6806 or
customer service at
[email protected]
Warning: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use damaged
or defective parts. lf you require replacement parts, contact our Product Support line at
1-800-556-6806 or customer service at [email protected].
• Please note: Not all hardware included in this package will be used.
Note: The washer and spacers are shown in accordance with the actual size
x4
M6/M8
[B]
Washers
07
[C1] x8
φ8.5x18x2.5mm
[C2] x4
φ8.5x18x10mm
[C3] x4
φ8.5x18x22mm
Spacers [if needed]
08
Level
02

06 x1
13/64 in.(5mm) Allen Key
Arm Assembly/Wall Plate
05 x1 03 x2
Arm Extension
(X4)
M6X10mm
B1
Bolt
B2 (X4)
M6
Washer
Supplied Parts and Hardware for Step 2
04 x2
TV Bracket
M6
M8
Note: The bolts are shown in accordance with the actual size
M6 x 15mm
[D1] x4
M6 x 35mm
[D2] x4
[Only one bolt size fits your TV]
TV Bolts
09
M8 x 50mm
[E3] x4
M8 x 25mm
[E1] x4
M8 x 35mm
[E2] x4
03
01 x1
Front Support

Select TV Bolts
Supplied Parts and Hardware for Step 3
Note: The lag screw is shown in accordance with the actual size
Washer
M8
A2
x4
Lag Screw
M8x65mm
x4
A1
Wall
Anchor
x4
A3
These anchors are for
concrete or brick walls
ONLY. DO NOT use them
in drywall or wood studs.
CAUTION!
M6 M8
Only one bolt size fits your TV.
Step 1 Secure the TV Brackets to Your TV
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination.
We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Too Short Too Long Correct Correct
Note: If necessary, the spacers can be used in multi-layer. If the installation fails after
trying various methods, please contact customer service at [email protected].
04

CAUTION: Ensure the TV Bracket [04] is
EQUALLY CENTERED on your TV AND
securely fastened in place.
07
B
D2/E2/E3
09
C1/C2/C3
08
04
Option B (For Round Back TV)
Alternate Spacer Setups
UP
Option A (For Flat Back TV)
Alternate
Spacer
Setups
Spacers may be necessary for 2 holes ONLY.
Option C (For TV with A “Bump”)
Alternate Spacer Setups
05
08
(If needed)
C1C2
09 D1/E1
07
B
04
08
(If needed)
C1C2
09 D1/E1
07
B
04
07
B
D2/E2/E3
09
C1/C2/C3
08
04 Alternate
Spacer
Setups

06
Step 2 Secure Front Support Assembly to the Arm Assemble/Wall
Plate
Option D
For cable interference or inset holes, use
spacers to create extra space between the
TV and TV brackets
08
Alternate Spacer Setups
07
B
D2/E2/E3
09
C1/C2/C3
08
2-1 Remove the 4 pcs pre-assembed bolts [B3] from front support [01] and
keep the bolts [B3] for the use in 2-2, then slightly loosen the 4 pcs
preassembled bolts [B4]
2-2 Insert the arm extensions [03] into the front support [01]. Then tighten the
bolts [B3] and [B4] to secure arm extensions [03] to front support [01].
04
06
03
B3
B3
B4
B4
01
01

Step 3
For wood stud installation, follow STEP 3A
For concrete installation, follow STEP 3B
Attach the Arm Assembly/Wall Plate [05] to Wall
Step 3A Wood Stud Option
X
● Ensure the arm assembly/wall plate [05] is securely fastened to the
wall before continuing to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum
1½ x 3½ in. (38 x 89 mm)
● Stud center must be verified
WARNING:
● Avoid potential personal injury or property damage! DO NOT over-tighten the lag
screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly
against the wall plate.
● Do not use wall anchor [A3] for this step
06
3A-1
3A-2
Position the arm assembly/wall
plate [05] at your desired
height and line up the holes with
your stud center line. Level the
wall plate and mark the holes.
2-3 Secure the front support assembly to arm assembly/wall plate
Use a stud finder(not included)
to locate wood studs or use an
awl (not included) to verify the
edges. Mark the edge and
center locations.
Awl
(Not lncluded)
HEAVY! You may need
assistance with this step.
07
06
B1 B2
16 in.(406mm)

7/32 in.(ø5.5mm)
2 9/16 in.(65mm)
Drill 4 pilot holes using a
7/32 in.(5.5mm) diameter drill
bit. Make sure the depth is not
less than 2 9/16 in.(65mm).
3A-3
Step 3B Solid Concrete or Concrete Block Option
WARNING:
● Avoid potential personal injury or property damage! DO NOT over-tighten the lag
screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly
against the wall plate.
● Ensure the arm assembly/wall plate [05] is securely fastened to the
wall before continuing to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Mount the arm assembly/wall plate [05] directly onto the concrete surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
● Never drill into the mortar between blocks
Wall Anchor
A3
33/64 in.(13mm)
Socket Wrench
Install the arm assembly/wall
plate [05] using lag screws [A1]
and washers [A2]. Tighten the
lag screws [A1] only until the
washers [A2] are pulled firmly
against the wall plate.
3A-4
A2 A1
Position the arm assembly/wall
plate [05] at your desired
height, level the wall plate and
mark the pilot hole locations.
3B-1
HEAVY! You may need
assistance with this step.
HEAVY! You may need
assistance with this step.
08

Drill 4 pilot holes using a
3/8 in.(10mm)diameter drill bit.
Make sure the depth is not less
than 2 3/4 in.(70mm). Never drill
into the mortar between blocks.
3/8 in.(ø10mm)
2 3/4 in.(70mm)
Use the hammer to
knock anchors [A3]
into the wall. Be sure
the anchors [A3] are
seated flush with the
concrete surface.
Install the arm assembly/wall plate [05] using lag
screws [A1], washers [A2] and anchors [A3]. Tighten
the lag screws [A1] only until the washers [A2] are
pulled firmly against the wall plate. DO NOT
over-tighten the lag screws [A1].
3B-2
3B-3
A3
A2 A1
Step 4 Secure the TV onto the Arm Assembly/Wall Plate [05]
1. Hang the TV onto the front support assembly.
2. Tighten the lock bolts [S] to secure TV onto the arm assembly/wall
plate [05] using screwdriver
①
Locking
②
S
1/2 in.(13mm)
Socket Wrench
HEAVY! You may need
assistance with this step.
HEAVY! You may need
assistance with this step.
09

3/8 in.(10mm)
Socket Wrench
(Not included)
Tilt Adjustment
1. Loosen four tilt bolts [T].
2. Adjust TV to your desired tilt angle.
3. Retighten four tilt bolts [T] to fix the tilt angle.
If needed, the TV can be levelled
Level Adjustment
06
1. Loosen the four bolts [B1].
2. Level your TV.
3. Retighten four bolts [B1] to hold TV in place.
B1
10
Tilt adjustment
T
Loosen Tighten
Note: Please do not over-tighten
or over-loosen the bolts
Note: Please do not over-tighten
or over-loosen the bolts

Thank you again for
choosing this Perlesmith product!
All of us at Perlesmith do appreciate your product purchase. We hope that you are as happy
with your product as we are designing and manufacturing it for you. We strive to provide you
with the best quality products and services in the industry. Please share your experience of our
product with others at www.perlesmith.com/pages/reviews if you are satisfied. Should you
have any issues, please don't hesitate to contact us.
Technical Support: 1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info: [email protected] (US/CA/DE/UK/FR/IT/ES/AU)
Please check www.perlesmith.com for more products and company information.