Perlesmith PSTVS13 User manual

PSTVS13
Table Top TV Stand
Thank you for choosing our product! We strive to provide the best
quality and services for our customers. Would you kindly share your
experience on Amazon if you are satisfied? Should you have any issues,
please don't hesitate to contact us.
Telephone：[phone] Mon-Fri 10am - 6pm (PST) (USA) (CAN)
Email：[email protected] (US/CA/DE/UK/FR/IT/ES/JP/AU)
V1.0

•Carefully open the carton, remove contents and lay out on cardbard or other protective
surface to avoid damage.
•Check to assure that all components were received undamaged. Do not use damaged or
defective parts.lf you require replacement parts, contact customer service at
[email protected].
WARNING
•Install and operate this product with care. Please read this instruction before beginning the
installation, and carefully follow all instructions contained herein. Use proper tools during
installation.
•Do not use this product for any purpose or in any configuration not explicitly specified in
this instruction. We hereby disclaim any liability for injury or damage arising from incorrect
assembly, incorrect mounting, or incorrect use of this product.
•
If you do not understand the instructions or have any concerns or questions, please contact
customer service at [email protected].
1
M8x15 (x4)
M-F M-G M-H
D5、D8 washer (x4)
M8x45 (x4)
5mm spacer(x8) 10mm spacer(x8)
M6x15 (X4) M6x30 (X4)
M-A M-B M-C M-D
(x2)
2(x1) 3
(x2)
7
(x2)
6
(x1) 8(x1)
5
(x1)
4
(x1)
M6-M10 wrench(x1)
I
D
D8 washer(x3) E
D10 washer(x1)
G
Rubber foot(x4)
F
D10 plastic
washer(x2)
Support Pillar
Support Pillar
TV Plate
Plastic Cover Tempered Glass
Monitor Brackets
Safety Lock
M8x65 (x4)
M-E
Component Checklist
H
5mm Allen key(x1)
M8x25(x3)
A
M10(x1)
B
M6(x4)
C

Connecting the Support Pillar to Support Pillar
Step 2
8
5
5
5
4
Support
Pillar
Tempered
Glass
5mm
Allen key
M8x25
STEP 1
A
D8
washer
Rubber
foot
D
G
H
1.1
1.2
Connecting the Support Pillar to Tempered Glass
x 1
x 1
x 1
x 3
x 3
x 4
x 1
x 1
x 1
x 1
x 2
x 1
4
4
Support
Pillar
6
Plastic Cover
8
G
8
4
H
Table
8
4
6
A
D
5
F
I
E
B
B
I
E
F
M10
D10 washer
D10 plastic
washer
M6-M10
wrench

Step 4 Measure VESA and Check TV screws
TV Plate
M6-M10
wrench
M6
Connecting the TV Plates to Support Pillar
x 2
x 1
x 4
x 1
1
1
2
STEP 3
I
C
1
12
C
C
I
I
5
Check TV screws
When attaching brackets to the flat
screen, be careful not to over tighten
screws and be sure that screws do
not bottom out in the mounting
holes.
Too Short Too Long
Correct Correct
Hand thread screws into the threaded inserts
on the back of your TV to determine which
screw diameter (M4, M6, or M8) to use.
Measure the distance between
the holes located at the back of
your TV (these measures may
form the shape of a square, or a
rectan-gle) and check that these
taken measures are within the
VESA(*) range for this wall
mount.(*) VESA: International
standard established by the TV
manufacturers used to determine
if LCD/LED TVs are compatble
with wall mounts.

Step 5 Mounting the Monitor Bracket to a TV
Step 6 Attaching TV to TV Plate
6.1
x 2
x 4
x 4
x 4
x 4
x 4
x 4
x 8
x 8
M8x15
M-F
M-G
M-H
D5、D8 washer
M8x45
5mm spacer
10mm spacer
M6x15
M6x30
M-A
M-B
M-C
M-D
3
3
3
Monitor
Brackets
M8x65
M-E
Firstly, make sure the diameter of the bolt (MA - E) fits your TV. Then, please see the figure
above. You will need to thread the bolt into the TV using the correct hole in the washer
(M-F) and spacer (M-H or M-G) if necessary. Please make sure the monitor brackets are
vertically centered and level with each other
1
(M)A to E
M-F
M-G/M-H

Adusting Angle of TV Stand
Step 7
7
Safety Lock
±30°
6.2
6
7
Fasten the screw
x 2
1