Perlesmith PSSS2 User manual

V2.0
Speaker Floor Stand Instruction Manual
Model: PSSS2
Thank you for choosing this PERLESMITH product! At
PERLESMITH we strive to provide you with the best quality
products and services in the industry. Please share your
experience of our product with others at www.perlesmith.com/
pages/reviews if you are satisfied. Should you have any issues,
please don't hesitate to contact us.
Technical Support:
1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US）
[email protected] (CA)
Website:
www.perlesmith.com

•Check package contents against Supplied Parts and Hardware List to assure that all
components were received undamaged. Do not use damaged or defective parts. lf you
require replacement parts, contact customer service at
[email protected] (US) / [email protected] (CA).
•Carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact
customer service at [email protected] (US)/[email protected] (CA).
•This product may contain moving parts. Use with caution.
•Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by
improper mounting, incorrect assembly or inappropriate use.
•Please check www.perlesmith.com for more products and company information.
IMPORTANT SAFETY INSTRUCTIONS
Phillips Screwdriver
TOOLS NEEDED (NOT INCLUDED)
SUPPLIED PARTS
Plastic Washer
[D] x2
Pad
[F] x4
Speaker Bracket
[03] x2
Upper Support Post
[02b] x2
Lower Support Post
[02a] x2
Decorative Cover
[04] x2
Foot with Nut
[A/B] x8 Bolt
[E] x2
PVC Washer
[C] x2
Base
[01] x2
01 02 03 04 05

STEP 1 Secure the Feet and Support Posts to the Base
A/B A B
01
02b
01 02 03 04 05

STEP 2 Secure the Speaker Bracket to the Upper Support Post
F
E
D
C
03
19/32 in.-13 25/32 in.
(15-350 mm)
01 02 03 04 05

STEP 3 Secure the Speaker to the Stand and Tilt Adjustment
5 29/32 in.-10 53/64 in.
(150-275 mm)
Loosen
01 02 03 04 05

Speaker
(not included)
TightenTighten
Note: The speaker must be installed
on the middle of the speaker bracket.
360 Degree All-round Tilt Adjustment
If needed, the speaker angle can be adjusted.
1. Remove the speaker from the stand.
2. Slightly loosen the bolt [E].
3. Tilt the speaker bracket [03] to desired angle.
4. Tighten the bolt [E] to secure the speaker bracket
in place.
E03
01 02 03 04 05

Thank you again for choosing
this PERLESMITH product!
All of us at PERLESMITH do appreciate your product purchase. We hope that you
are as happy with your product as we are designing and manufacturing it for you.
We strive to provide you with the best quality products and services in the
industry. Please share your experience of our product with others at
www.perlesmith.com/pages/reviews if you are satisfied. Should you have any
issues, please don't hesitate to contact us.
Technical Support: 1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info: [email protected] (US)/[email protected] (CA)
Please check www.perlesmith.com for more products and company information.

PERLESMITH offers products
in these categories
Anti-tip Straps
TV Stands AV Shelves
Speaker Stands TV Carts
Full Motion Mounts Tilt Mounts Corner Mounts
Please remember us when you need one.