Perlick HP15 User manual

PART NUMBER 1033280
INSTRUCTION START DATE 11/29/2021
AFFECTED MODELS HP15, HP24, HC24 & HA24
KIT PART NUMBER(S) RS-SK-15L, RS-SK-15R, RS-SK-24L, RS-SK-24R,
RS-SK-18L & RS-SK-18R
INSTRUCTION PURPOSE WORK INSTRUCTIONS FOR STACKING 15” AND
24’’ WITH DOOR CABINET UNITS.
TOOLS REQUIRED
PPE (GLOVES AND SAFETY GOOGLES)
PHILIPS SCREWDRIVER
DRILL, AND 5/32’ DRILL BIT

23/3/2022
OPERATION 1: DRILL OUT RIVETS
OPERATION 2: LEG LEVELERS & GRILL REMOVAL
CAUTION: THESE CABINETS ARE EXTREMELY HEAVY. ENSURE THAT YOU HAVE ENOUGH PEOPLE
ON HAND TO HELP REPOSITIONING THE UNIT SO IT CAN BE DONE SAFELY AND WITHOUT DAMAGE.
•UTILLIZING A DRILL WITH A 5/32” DRILL BIT, DRILL OUT TOP ROW OF RIVETS ALONG BACK OF THE
BOTTOM CABINET.
2 RIVETS ON 24” AND 15” WIDE CABINETS
CAUTION: THESE CABINETS ARE EXTREMELY HEAVY. ENSURE THAT YOU HAVE ENOUGH PEOPLE
ON HAND TO HELP REPOSITIONING THE UNIT SO IT CAN BE DONE SAFELY AND WITHOUT DAMAGE.
1. LAY UPPER CABINET ON ITS BACK AND REMOVE LEG LEVELERS FROM ALL CABINET SIZES.
2. UTILIZING A PHILLIPS HEAD SCREWDRIVER, REMOVE GRILL BY REMOVING THE TWO SCREWS THAT ARE
LOCATED ON EACH SIDE OF GRILL (SEE PIC).
LEG LEVELERS
SCREW (2X)

33/3/2022
OPERATION 3: ATTACHING MOUNTING PLATE
OPERATION 4: STACKING UPPER UNIT ONTO LOWER UNIT
CAUTION: THESE CABINETS ARE EXTREMELY HEAVY. ENSURE THAT YOU HAVE ENOUGH PEOPLE
ON HAND TO HELP REPOSITIONING THE UNIT SO IT CAN BE DONE SAFELY AND WITHOUT DAMAGE.
1. WHILE CABINET LAYING ON ITS BACK, BRING MOUNTING PLATE AND ALIGN IT TO THREADED HOLES WHERE
LEG LEVELERS WERE REMOVED IN STEP 2. THE FLANGE SHOULD BE POINTING AWAY FROM THE UNIT.
2. UTILIZING A PHILLIPS HEAD SCREWDRIVER. SECURE MOUNTING PLATE BY FASTENING 1/4-20 MACHINE
SCREWS (4X) PROVIDED IN KIT.
CAUTION: THESE CABINETS ARE EXTREMELY HEAVY. ENSURE THAT YOU HAVE ENOUGH PEOPLE
ON HAND TO HELP REPOSITIONING THE UNIT SO IT CAN BE DONE SAFELY AND WITHOUT DAMAGE.
1. PLACE UPPER UNIT ON TOP OF LOWER UNIT. ALIGN FLANGE HOLES WITH THE RIVET HOLES PREVIOUSLY DRILLED.
2. UTILIZING A PHILIPS HEAD SCREWDRIVER, SECURE UPPER UNIT BY FASTENING #10 SCREWS PROVIDED IN KIT.
SCREWS (2X)
ALIGNMENT SHOWN
NOTE: TO PREVENT DAMAGE TO THE COMPRESSOR, WAIT 24
HOURS BEFORE POWERING ON UNIT AFTER TURNING THE
CABINET BACK TO ITS UPRIGHT POSITION.
FLANGE
SCREWS (4X)

43/3/2022
OPERATION 5: SCREWS REMOVAL
OPERATION 6: INSTALL MOUNTING BRACKET
1. WITH A PHILLIPS HEAD SCREWDRIVER, REMOVE SCREWS (2X) FROM UNIT SIDE BRACKETS.
2. KEEP COMPONENTS (SCREWS) ASIDE FOR RE-ASSEMBLY LATER.
SCREWS
SCREWS
BRACKET
1. ALIGN MOUNTING BRACKET TO HOLES (4X), 2 HOLES FROM WHERE OLD GRILL WAS SECURED TO (STEP 2),
AND THE OTHER TWO HOLES ARE THE ONES FROM PREVIOUS STEP (STEP 5).
2. UTILIZING A PHILLIPS HEAD SCREWDRIVER, SECURE BRACKET BY UTILIZING TWO SCREWS FROM STEP 5, AND
TWO SCREWS FROM STEP 6.
68 15/16”
23 7/8”
24 1/16”

53/3/2022
OPERATION 7: INSTALL FEMALE LATCHES TO BRACKET
OPERATION 8: PREPARING GRILL (LATCH & BUMPERS)
1. CAREFULLY INSTALL FEMALE LATCHES (2X) INTO MOUNTING BRACKET ONE ON EACH SIDE BY PRESSING
DOWN FIRMLY AGAINST SQUARE OPENING IN BRACKET. MAKE SURE FEMALE LATCHES ARE ALL WAY IN
AND ORIENTED AS PICTURE BELOW (VERTICAL OPENING).
FEMALE LATCH (2X)
MALE LATCHES
BUMPERS
1. INSTALL MALE LATCHES ON GRILL BY PRESSING FIRMLY AGAINST SQUARE OPENING ON EACH SIDE OF GRILL. MAKE
SURE THE MALE LATCHES ARE FULLY ENGAGED AND ORIENTED VERTICALLY.
2. PEEL OFF THE PAPER OF EACH BUMPER PAD EXPOSING THE ADHESIVE SURFACE AND PLACE EACH ONE AS ORIENTED
IN THE PICTURE BELOW.

63/3/2022
OPERATION 9: INSTALL STACKING GRILL
OPERATION 10: FINAL STAGE
REV # ECO # DESCRIPTION DATE NAME
A 2021-5401 NEW RELEASE 3/02/2022 JIT
1. PLACE AND ALIGN STACKING GRILL TO HOLES LOCATED RIGHT ABOVE FEMALE LATCHES ON EACH SIDE OF
MOUNTING BRACKET.
2. UTILIZING A PHILLIPS HEAD SCREWDRIVER, SECURE STACKING GRILL WITH TWO #10 SCREWS PROVIDED IN KIT.
SCREWS (2X)
HOLE
1. MAKE SURE TO WAIT 24 HOURS BEFORE POWERING ON UNIT AFTER TURNING THE CABINET
BACK TO ITS UPRIGHT POSITION.
NOTE:
WHEN USING STACKING KIT TO JOIN (2) HH24
OR HA24 UNITS, A WALL MOUNT ANTI-TIP
KIT MUST BE INSTALLED. SEE CABINET
INSTALLATION MANUAL FOR INSTRUCTIONS.