Pet Gear 3-IN-1 BIKE BASKET User manual

INSTRUCTION MANUAL
3-IN-1 BIKE BASKET
PG1450
Car Seat/Carrier/Bike Basket
To see our full line of products, visit us online at: www.petgearinc.com
CUSTOMER SERVICE HELP DESK
[email protected]
Toll-Free 877-752-9123 - Eastern Standard Time 8am-3pm, Monday through Friday
For The ON-THE-GO Pet™

BIKE BASKET • PG1450
2
PARTS LIST
TO ATTACH CARRYING STRAP
Step 1. To attach carrying strap, clip each end of the carrying strap to the two metal rings
(located on each side of The 3-in-1 Bike Basket, shown in Figure A).
3-in-1 Bike
Basket
Carrying Strap
Comfort Pad
Universal Bike
Attachment
Check that you have all the parts shown BEFORE assembling your product.
If any parts are missing, call Customer Service.
A.
Support Wire

BIKE BASKET • PG1450 3
TO USE AS CAR SEAT AND/OR BOOSTER
Step 2. To use the 3-in-1 Bike Basket as a car
seat, take seat belt and place it through the
seat belt straps and buckle seat belt to secure
(shown in Figure B).
Step 3. To use the 3-in-1 Bike Basket as a booster,
do step number 2, then attach carrying strap around
headrest and adjust to a secure position (shown in
Figure C).
B.
C.
TO USE BIKE ATTACHMENT
Step 4. To use the 3-in-1 Bike Basket as a bike
basket, you need a bike and the Universal
Bike Attachment with all the included pieces
(shown in Figure D).
D.
HANDLEBAR MOUNTING
BRACKETS
BOLT AND
FASTENING
NUTS
UNIVERSAL BIKE ATTACHMENT
SEAT BELT STRAP
SEAT BELT STRAP

BIKE BASKET • PG1450
4
EXTENSION A EXTENSION B
F.
G.
Step 5. To attach the Universal Bike
Attachment to a bike, rst unscrew the
bolts and nuts so that both handlebar
mounting brackets are disconnected
from the bike attachment (shown in
Figure E).
Step 6. Put the mounting
brackets on the handlebar of
your bike so that extension
part A and B are facing forward
(shown in Figure F).
Step 7. Next, you have to
connect the bike attachment
to the mounting brackets.
Take bike attachment and slide
extension A of both handlebar
mounting brackets into the top
slots while sliding extension
B underneath the second slots
of the bike attachment.
Once extensions are in place,
put bolts through the exten-
sions and tighten with both
fastening nuts.
Make sure attachment is
straight and even.
This should look like Figure G.
HANDLEBAR MOUNTING
BRACKETS (2)
HANDLEBAR
MOUNTING
BRACKETS
HANDLEBAR
MOUNTING
BRACKETS
HANDLEBAR
MOUNTING
BRACKETS
HANDLEBAR
MOUNTING
BRACKETS
BOLT AND FASTENING
NUTS (2)
TO USE BIKE ATTACHMENT
E.
UNIVERSAL BIKE ATTACHMENT

BIKE BASKET • PG1450 5
Step 9. Once the universal bike
attachment is connected and fully
secured to the bike, the bike basket
is now ready to be attached.
Put bike basket in the front of the
bike so the handle clip is above the
insertion slot.
Once handle clip and insertion slot
are aligned, push the handle clip
down into the insertion slot (shown
in Figure I).
Step 8. You may need to tighten swing arm
screws with a Phillips™ screwdriver to t swing
arm to your handlebar stem/steering column so
that it is tight and stable (shown in Figure H).
After you tighten the 2 swing arm screws, take
the 2 plastic caps/plugs (found in the instruction
booklet packaging) and push them into place
over the 2 swing arm screws.
SWING ARM
SCREWS
H.
TO USE BIKE ATTACHMENT
I.
SEAT
BELT
STRAP
SEAT
BELT
STRAP
HANDLE CLIP
INSERTION SLOT

BIKE BASKET • PG1450
6
TO USE SUPPORT WIRE
To add support to the bottom of the bike basket, remove wire from pouch and slide into pocket.
Remove wire from pouch. Slide wire into pocket.
Step 10. Connect carrying strap to one of the side metal rings (located on each side of The 3-in-1 Bike Basket).
Then, put the strap through one side of the seat belt straps. Next, bring strap around handlebar stem and put
through other seat belt strap. Attach strap to other metal ring on other side. Tighten strap so there is as little slack
as possible (shown in Figure J).
SEAT BELT STRAP SEAT BELT STRAP
J.
TO USE BIKE ATTACHMENT
POCKET

BIKE BASKET • PG1450 7
WARNING!
TO USE SUPPORT WIRE
REPLACEMENT PARTS
FOR PETS ONLY.
Not intended to be used as a restraining device for aggressive or dangerous animals that dig, chew or paw
aggressively. Do not leave your pet unattended. PET GEAR is not liable for any damage caused by aggressive,
destructive, immature or untrained animals. Do not use near an open or exposed ame. Failure to follow these
warnings and the instructions could result in serious injury or death.
Wire shown supporting against bike.
Use only PET GEAR replacement parts.
Please have your model number ready before calling.
You can also request parts: http://www.petgearinc.com/main.asp?sel=2
192 Sheldon Avenue • West Rutland, VT 05777 • 877-752-9123 • www.petgearinc.com