Pet Waste Eliminator E3SP User manual

Need Help? Give us a call! Pet Waste Eliminator •1-800-790-8896 •www.petwasteeliminator.com
INSTALLATION GUIDE
Sponsored
Pet Waste
Station
ITEM: E3SP
E
B
D
C
PET WASTE ELIMINATOR
SUPERIOR STATIONS:
HLifetime Guarantee
HRust-Proof Construction
HUniversal Fit holds all bags on
header cards or rolls
NEVER RUN OUT OF
BAGS AGAIN!
Join our exclusive
Refill Program and get
FREE SHIPPING on
every Bag Order!
Call to join today!
REV 8/18
Sponsorship
Station
Item E3SP
Sponsorship Kit Includes:
A. 1 12”x 6” Custom Sponsor Sign (Item E840)
B. 1 12”x18” Aluminum Sign (Item E802)
C. 1 Dispenser Box (Item E1)
D. 1 8-ft Steel Sign Post (Item E18)
D. 1 10-gal Waste Receptacle with attached lid
(Item E10)
F. 4 Mounting Hardware Sets— each set
includes 2 nuts, bolts and washers
G. 80 Pet Waste Bags (Item E41)
H. 50 Waste Receptacle Liners
Optional Tools Needed:
• Socket Driver or Adjustable Wrench
• Level
• Post Hole Driver
H
G
F
A

2. Station Assembly
1. Pole Installation
Using a post hole driver (not included), drive the sign post (D) approximately 12-15” into
the ground. Make sure that the “hollow” or “recessed” side of the post is facing where
you want the front of the unit to face. We recommend that the pole is no less than 12”
underground to support the weight of the waste receptacle (E) properly. Use a level (not
included) to ensure the pole is standing upright and will properly support the unit. Adjust
if necessary.
Need Help? Give us a call! Pet Waste Eliminator •1-800-790-8896 •www.petwasteeliminator.com
3. Station Preparation
18”
17”
12”
24”
2”
15”
1”
1. Using the first hardware set (F), secure the small sign (A) to the top of the steel post
(D) with a bolt and washer at the top of the sign and another at the bottom. The washers
should be next to the printed side (front) of the sign and the nuts are secured on the
outside/back of the post. To ensure the best outcome, make sure the sign is flush with
the top of the pole.
2. Using the second hardware set (F), secure the large sign (B) directly below the small
sign (A) with a bolt and washer at the top of the sign and another at the bottom leaving
about 1” in-between. The washers should be next to the printed side (front) of the sign
and the nuts are secured on the outside/back of the post.
3. Using the third hardware set (F), attach the dispenser box (C) directly under the sign
leaving about 1” in-between. Open the box, align the holes to the steel post and attach
with the two bolts. The washers should be used on the inside of the box with the nuts
secured to the outside/back of the post.
4. Using the final hardware set (F), secure the waste receptacle (E) to the steel post
at the top and the bottom with the washers facing the inside of the waste can and the
nuts on the outside/back of the post. Make sure that the receptacle is approximately
12 inches below the dispenser box to allow for the lid to be open and trash to be easily
removed. This should leave your receptacle approximately 2 inches off the ground which
will help prevent any damage to the station from bad weather conditions.
1. Insert one waste liner (H) into the waste receptacle and fold over the rim. Open the
dispenser box and insert up to 10 header cards of bags (G) onto the prongs inside the
dispenser. Close the station, pull the top bag through the hole and you’re all set!
Note: This dispenser fits all types of bags. If you are using boxed bags (Item E40), you will need
to slip a converter (Item E22) onto the prongs inside the dispenser and insert the boxes into the
converter.
Please contact us immediately if you have any missing or damaged items
or need any additional assistance. Thank you.
1”
6”