PFU Limited FI-667PR IMPRINTER Manual

P3PC-2262-03EN
Operator’s Guide
fi-667PR Imprinter

Contents
Introduction................................................................................................................................................. 1
1. Preparations............................................................................................................................................ 5
1.1. Inspect the Package Contents..................................................................................................................... 5
1.2. Names of Component Parts......................................................................................................................... 5
2. Installation............................................................................................................................................... 7
2.1. Installing the Imprinter................................................................................................................................. 7
2.2. Installing the Print Cartridge ....................................................................................................................... 9
2.3. Operating Test ............................................................................................................................................ 10
3. Basic Operation .....................................................................................................................................11
3.1. Positioning the Print Cartridge...................................................................................................................11
3.2. How to Use the Paper Guides.....................................................................................................................11
3.3. Print Setup .................................................................................................................................................. 12
3.4. Replacing the Print Cartridge .................................................................................................................... 12
3.5. Removing Jammed Documents ................................................................................................................ 14
4. Daily Care .............................................................................................................................................. 15
4.1. Cleaning the Print Cartridge...................................................................................................................... 15
4.2. Cleaning the Imprinter ............................................................................................................................... 15
4.3. Cleaning the Rollers................................................................................................................................... 16
4.4. Removing the Imprinter ............................................................................................................................. 16
5. Error Messages..................................................................................................................................... 17
6. Specifications ....................................................................................................................................... 19
© PFU LIMITED 2008-2015.
The contents of this manual are subject to change without notice.
This manual may not be reproduced, adapted or translated without prior written permission.
READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT. IF THIS PRODUCT IS NOT USED
CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO USERS OR BYSTANDERS.
While all efforts have been made to ensure the accuracy of all information in this manual, PFU LIMITED assumes no
liability to any party for any damage caused by errors or omissions or by statements of any kind in this manual, its
updates or supplements, whether such errors are omissions or statements resulting from negligence, accidents, or any
other cause.
PFU LIMITED further assumes no liability arising from the application or use of any product or system described herein;
nor any liability for incidental or consequential damages arising from the use of this manual.
PFU LIMITED disclaims all warranties regarding the information contained herein, whether expressed, implied, or
statutory.
PFU LIMITED assumes no liability for incidental or consequential damages arising from the use of this product, and any
claims by a third party.

fi-667PR Imprinter Operator’s Guide | 1
Introduction
Thank you for purchasing the fi-667PR Imprinter option for
the fi-6670 / fi-6670A Color Image Scanner.
This guide explains how to install and use the imprinter.
(For further details about the functions and operations of the
fi-6670 / fi-6670A Image Scanner, refer to the “Image
Scanner Operator’s Guide” provided by the SETUP
DVD-ROM bundled with fi-6670 / fi-6670A.)
This guide also contains other important information, such
as procedures for replacement of consumables. Keep this
guide in a convenient and safe place so that you can refer to
it whenever necessary.
We hope this manual will be helpful in your future use of the
fi-667PR Imprinter.
Manufacturer
PFU LIMITED
YOKOHAMA i-MARK PLACE, 4-4-5 Minatomirai,
Nishi-ku, Yokohama, Kanagawa 220-8567, Japan
Trademarks
Microsoft, Windows and Windows Server are either
registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
PaperStream is a registered trademark of PFU LIMITED in
Japan.
Other company names and product names are the registered
trademarks or trademarks of the respective companies.
How Trademarks Are Indicated In This
Manual
References to operating systems (OS) are indicated as
follows:
Product
Indication
Windows Server
®
2008 Standard
(32/64-bit)
Windows Server®2008 R2 Standard
(64-bit)
Windows Server
2008 (*1)
Windows
®
7 Home Premium (32/64-bit)
Windows®7 Professional (32/64-bit)
Windows®7 Enterprise (32/64-bit)
Windows
®
7 Ultimate (32/64-bit)
Windows 7 (*1)
Windows Server
®
2012 Standard (64-bit)
Windows Server
2012 (*1)
Windows Server
®
2012 R2 Standard
(64-bit)
Windows Server
2012 R2 (*1)
Windows®
8 (32/64-bit)
Windows®8 Pro (32/64-bit)
Windows
®
8 Enterprise (32/64-bit)
Windows 8 (*1)
Windows
®
8.1 (32/64-bit)
Windows®8.1 Pro (32/64-bit)
Windows
®
8.1 Enterprise (32/64-bit)
Windows 8.1 (*1)
*1: Where there is no distinction between the different
versions of the above operating system, the general term
"Windows" is used.
Regulatory Information
FCC declaration
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit
different from that to which the receiver is located.
-Consult your dealer or an experienced radio/TV
technician.
FCC warning: Changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Canadian DOC Regulations
This digital apparatus does not exceed the Class B limit for
radio noise emissions from digital apparatus set out in the
Radio interference Regulations of the Canadian Department
of Communications.
This Class B digital apparatus complies with Canadian
ICES-003.
Le présent appareil numérique n'émet pas de parasites
radioélectriques dépassant les limites applicables aux
appareils numériques de la classe B, limites prescrites dans
le Règlement pour le brouillage radioélectrique qui fut dicté
par le Ministère des Communications du Canada.
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
Bescheinigung des Herstellers /
Importeurs
Für den fi-667PR wird folgendes bescheinigt:
•In Übereinsstimmung mit den Bestimmungen der
EN45014(CE) funkentstört
•Maschinenlärminformationsverordnung 3. GPSGV:
Der höchste Schalldruckpegel beträgt 70 dB (A) oder
weniger, gemäß EN ISO 7779.
Dieses Gerät wurde nicht für die Benutzung in
unmittelbarer Umgebung starker Lichtquellen (z. B.
Projektoren) konzipiert.

2 |
Use in High-Safety Applications
This product has been designed and manufactured on the
assumption that it will be used in office, personal, domestic,
regular industrial, and general-purpose applications. It has
not been designed and manufactured for use in applications
(simply called "high-safety applications" from here on) that
directly involve danger to life and health when a high
degree of safety is required, for example, in the control of
nuclear reactions at nuclear power facilities, automatic
flight control of aircraft, air traffic control, operation control
in mass-transport systems, medical equipment for
sustaining life, and missile firing control in weapons
systems, and when provisionally the safety in question is
not ensured. The user should use this product with adopting
measures for ensuring safety in such high-safety
applications. PFU LIMITED assumes no liability
whatsoever for damages arising from use of this product by
the user in high-safety applications, and for any claims or
compensation for damages by the user or a third party.
Conventions
Warning Indications Used in This Manual
This indication alerts operators to an
operation that, if not strictly observed, may
result in severe injury or death.
This indication alerts operators to an
operation that, if not strictly observed, may
result in safety hazards to personnel or
damage to equipment.
Symbols Used in This Manual
This manual, in addition to the above warning indications,
uses the following symbols in its explanations.
This symbol alerts operators to particularly
important information. Be sure to read this
information.
This symbol alerts operators to helpful advice
regarding operation.
A TRIANGLE symbol indicates that special care
and attention are required.
The drawing inside the triangle shows the specific
caution.
A CIRCLE with a diagonal line inside indicates an
action that users may not perform.
The drawing inside or under the circle shows the
specific action that is not allowed.
Outline characters on a colored background show
instructions users should follow.
It may also include the drawing that shows the
specific instruction.
Screen Examples in This Manual
Microsoft product screenshots are reprinted with
permission from Microsoft Corporation. The screen
examples in this manual are subject to change without
notice in the interest of product improvement.
If the actual screen differs from the screen examples in this
manual, operate by following the actual displayed screen
while referring to the user’s manual of the scanner
application you are using.
The screen examples used in this manual are of the
PaperStream IP (TWAIN) driver.
The screenshots used in this manual are of Windows 7. The
windows that appear and the operations differ by the
operating system. Also note that with some scanner models,
the screens and operations may differ from this manual
when you update the PaperStream IP (TWAIN) driver. In
that case, refer to the manual provided upon updating the
driver.
About Maintenance
The user must not perform repairs on this product.
Contact the store where you purchased the scanner or an
authorized FUJITSU Image Scanner service provider to
have repairs made on this product.
Safety Precautions
FOLLOW THESE INSTRUCTIONS AND BE SURE TO
HEED ALL WARNINGS AND CAUTIONS DESCRIBED
BELOW.
Do not damage the AC cable.
A damaged AC cable may cause fire or electric shock.
Do not place heavy objects on AC cables, or pull,
bend, twist, heat, damage or modify AC cables.
Do not use damaged AC cables or power plugs, or
install any cables or power plugs to loose wall
sockets.
Use only specified AC cables and connector
cables.
Use only specified AC cables and connector cables.
Failure to use the correct cables might cause electric
shock and/or device failure.
Please don’t use the AC cable provided with this
device for other devices, since this might cause
device failure and other troubles or an electric shock.
Make sure to ground the device.
Make sure to ground the device to avoid electric
shock.
Be sure to ground the device before plugging into a
power outlet.
Unplug from the outlet before removing the ground
connection.
WARNING
CAUTION
WARNING

fi-667PR Imprinter Operator’s Guide | 3
Use this device only at the indicated power
voltage. Do not connect to multiple-power
strips.
Use this device only at the indicated power voltage
and current. Improper power voltage and current
might cause fire or electric shock. Do not connect to
multiple-power strips.
Do not touch the AC cable with wet hands.
Do not touch the power plug with wet hands. Doing so
might cause electric shock.
Wipe any dust from the power plug.
Wipe off any dust from metal parts on the power plug
or metal fittings with a soft, dry cloth. Accumulated
dust might cause fire or electric shock.
Do not install the device in locations that has oil
smoke, steam, humidity, and dust.
Do not install the imprinter in locations subject to oil
smoke, steam, humidity, and dust. Doing so might
cause a fire or electric shock.
Do not use the device if you smell a strange
odor.
If you detect heat coming from the device or detect
smoke, strange smells or noises, immediately turn off
the scanner and then disconnect its power plug. Make
sure that any smoke coming from it has stopped,
before contacting the store where you bought the
scanner or an authorized FUJITSU scanner service
provider.
Turn the scanner OFF if it is damaged.
If the device is damaged for any reason, turn the
scanner off and unplug the power cable. Contact the
store where you purchased the scanner or an
authorized FUJITSU scanner service provider.
Do not put liquids or foreign objects inside the
imprinter.
●Do not insert or drop metal objects in to the device.
●Do not scan wet documents or documents with
paper clips or staples.
●Do not splash or allow the device to get wet.
●If foreign objects (water, small metal objects,
liquids, etc.) get inside the device, immediately
turn off the scanner and disconnect the power plug
from the power outlet. Then, contact the store
where you bought the scanner or an authorized
FUJITSU scanner service provider. Pay particular
attention to this warning in households where
there are small children.
Unplug the scanner when a trouble occurs.
Immediately unplug the scanner when a trouble
occurs.
Never cut the ground connection until the scanner is
unplugged from the power outlet.
Do not touch the inside of the device unless
necessary.
Do not take apart or modify the device. The inside of
the device contains high-voltage components.
Touching these components might cause electric
shock or fire.
Do not use aerosol sprays near the device.
Do not use any aerosol sprays or alcohol based
sprays to clean the device.
Dust blown up by strong air from the spray may enter
the inside of the device. This may cause the device to
fail or malfunction.
Sparks, caused by static electricity, generated when
blowing off dust and dirt from the outside of the device
may cause a fire.
Do not place the scanner within the reach of
small children.
To avoid injuries, do not place the scanner in an area
where small children may be able to reach.
Do not touch the heated section for a long time.
Do not touch the heated section such as the bottom of
the scanner for a long time. Doing so may cause a
low-temperature burn on your skin.
Do not cover the scanner with something during
its operation.
Do not use the scanner while covered with a blanket,
etc. Doing so may raise the hot air inside and cause a
fire.
Do not use the scanner where it gets wet.
Do not use the scanner at a place such as a
bathroom, shower room, or swimming pool where it
may easily get wet. Doing so might cause electric
shock or fire.

4 |
The following describes important cautions.
Do not install the device on unstable surfaces.
Make sure that the device is installed on a flat, level
surface and that none of its parts extend beyond the
surface top, such as a desk or table. Do not install
the device on unstable surfaces. Install the device
on a level surface that is free of vibration to prevent
it from falling.
Install the imprinter on a strong surface that will
support the weight of the imprinter and other
devices.
Firmly insert the power plug.
Firmly insert the power plug as far it can go into the
power outlet.
Do not block the ventilation ports.
Do not block the ventilation ports. Blocking the
ventilation ports generates heat inside of device,
which may result in fire or device failure.
Do not place heavy objects or climb on top of
the imprinter.
Do not place heavy objects on the device or use the
device's surface top to perform other work.
Improper installation might cause injuries and
device failure.
Do not use the device immediately after
moving it from a cold place into a warm room.
Do not use the device immediately after moving it
from a cold place into a warm room. Condensation
may occur, which might lead to scanning errors. Let
the device dry about one or two hours before you
use it.
Before moving the device, disconnect the
power plug from the power outlet.
Do not move the device with the power and
interface cables connected as this can damage the
cables, which can later cause fire, electric shock as
well as injury.
Before moving the device, be sure to disconnect the
power plug from the power outlet, and all other data
cables.
Make sure that the floor is free of any obstructions.
Protect the device from static electricity.
Install the device away from strong magnetic fields
and other sources of electronic noise. Also, protect
the device against any static electricity, which can
cause the device to malfunction.
Avoid any contact when device is in use.
Avoid touching any device mechanism during
scanning since this may cause injuries.
Disconnect the power plug from the power
outlet when the device is not used for a long
period of time.
When the device is not going to be used for a long
period of time, be sure to disconnect the power plug
from the power outlet for safety.
Do not install the device in the direct sunlight.
Do not install the device under direct sunlight or
near heating apparatus. Doing so might cause
excessive heat to build up inside the device, which
can cause device trouble or even fire. Install the
device in a well-ventilated location.
Handle documents carefully.
When handling documents, be careful not to cut your
fingers with them.
Do not make the scanner wet while carrying it
outside.
When carrying the scanner outside while it is raining
or snowing, pay special attention so the scanner
does not get wet.
CAUTION

fi-667PR Imprinter Operator’s Guide | 5
1. Preparations
1.1. Inspect the Package Contents
Make sure that all items shown below are included in the
package.
If anything is missing or damaged, contact your FUJITSU
scanner dealer or an authorized FUJITSU scanner service
provider.
Imprinter (×1)
Attachment Guide (×1)
Print Cartridge (×1)
Operator’s Guide (×1)
1.2. Names of Component Parts
<Imprinter Unit>
Front Side
Rear Side
<Attachment Guide>
Lever
Lift the lever to detach the
Imprinter from the
scanner.
EXT cable
Print Cartridge Cover
Connecting Pin
Fix Claw
Screw
Print
section

6 |
<Imprinter with Scanner Installed>
Front Side
Rear Side
<Inside of the Imprinter>
ADF (Automatic Document Feeder)
Operator Panel
ADF Paper Chute
Imprinter
Stacker
ADF Paper Chute
ADF Open Button
ADF (Automatic Document Feeder)
Imprinter
Paper Guide
Print Cartridge Holder
Print Cartridge Cover

fi-667PR Imprinter Operator’s Guide | 7
2. Installation
2.1. Installing the Imprinter
Install the imprinter as follows:
1. Switch off the scanner and disconnect the
electrical power cable.
2. Remove the Stacker from the scanner.
Slowly push down the Stacker as shown below until the
connecting protrusion is unhooked.
Pull the Stacker towards the arrow direction to release it.
3. Remove the cover located under the stacker.
You must remove the stacker and cover
before installing the imprinter to the scanner.
4. Install the imprinter to the scanner.
Check the insertion direction of the Attachment Guide.
Check the Shaft from below.
Locate the Attachment Guide along the Shaft.
Push up the Attachment Guide.
Attachment Guide
ADF
Shaft
Scanner
ADF
Shaft

8 |
UHow to remove the Attachment Guide
Pressing your fingers on the Attachment Guide,
slide it down and out to remove.
5. Remove the attached screw from the imprinter’s
rear portion.
6. Install the imprinter to the scanner.
To install the imprinter to the scanner, insert the
connecting pins located on the imprinter’s rear
component into the scanner’s round holes.
●Hold the bottom of the imprinter whenever
lifting it up.
●Attach the imprinter firmly on to the scanner.
(→Confirm that the imprinter does not
separate from the scanner when pulled.)
●Be careful not to pinch your fingers.
7. Attach the Screw to fix the imprinter. (1 position)
8. Connect the EXT Cable to the EXT connecter on
the rear side of the scanner.
The imprinter will not work if the EXT cable is
not connected to the scanner. Scanning when
the EXT cable is not connected can cause
documents to jam inside the imprinter.
9. Replace the cover (removed in Step 3) to the
imprinter.
Hook the cover onto the imprinter by fitting the cover's
lower side slots to the corresponding protrusions on each
side of the imprinter.
Pushing on the upper part of the cover, fix it to the
imprinter.
Screw
Connecting Pin
See the imprinter in
this direction.
Screw
EXT Cable
EXT connecter