PG CL-CB100 User manual

ITEM# CL-CB100| 10000 LUMEN LED COB LED
ITEM# CL-CB100| 10000 LUMEN LED COB LED
CARE FOR YOUR PRODUCT:
Your product will last for many years with minimum care. Therefore, it is
essential to clean the product periodically. Use a soft, non-abrasive cloth or
a mild, non-abrasive glass cleaner. It is essential NOT to use any solvents or
harsh cleaning agents. When cleaning, make sure the power is OFF. Do
not spray liquid directly onto the product or wiring. Instead, spray or pour a
small amount into the cloth and clean the product.
CARE FOR YOUR PRODUCT:
This product has a two-year warranty from the date of purchase—
this guarantees against failure due to factory defects, whether caused
by materials or workmanship. The warranty is non-transferable and
only pertains to the original purchaser. Proof of purchase is required
for any repair or replacement, so please keep your proof of purchase
receipt. This warranty does not cover normal wear and tear or
damage due to misuse. Misuse of this product includes but is not
limited to:
• Using outdoors in extreme weather conditions.
• Opening the product’s housing.
• Any attempts to update, remodel or x the unit yourself.
WARNING:
YOU SHOULD ALWAYS FOLLOW BASIC PRECAUTIONS.
Read, follow, and understand all instructions and warnings before beginning any
installation of this product. Failure to do so can result in electric shock, re, or
other injuries, including death. This product should be installed following these
instructions, electrical codes, and by the National Electric Code (NED). Save this user
manual for instructions and warnings for possible future relocation and installation.
CAUTION:
• NEVER submerge this product in water!
• Do not install this bulb in places where water accumulates.
• Do not use on hot surfaces.
• Do not remove the lens protecting the LED.
• Do not use in areas near a gas source.
• It is NOT possible to change the LED light source.
• This light is not intended for use in potentially explosive environments.
This is NOT a vapor proof light.
• This bulb is NOT A TOY and is not suitable for use by children.
• This device is not intended for use with emergency exits.
TROUBLESHOOTING:
Problem Possible Cause Solution
The product does The power is o Verify the power is ON
not turn on Bad connection Check the wiring
Faulty switch Test and/or replace the switch
Circuit breaker Discontinue use immediately Call customer service 1-888-745-4837
trips or fuse blows Call an electrician
when light is turned on
Lumen: 10,000LM
Watts: 85W
Equivalent: 500W Incandescent
LED Lifespan: 30,000 Hours
Operating Voltage: 120V
CRI: 80
Color Temp (CCT): 5000K
Base: E26 / Standard Edison Base
Damp Rated
Operating Temperature: -13°F to 104°F(-25°C to 40°C)
EYES:
• DO NOT look directly at the LED lights.
• DO NOT remove the LED lights protective covering.
If you have questions or missing parts, please contact our customer care at 1-888-745-4837 If you have questions or missing parts, please contact our customer care at 1-888-745-4837
WARNING:
RISK OF ELECTRICAL SHOCK.
TO AVOID ELECTRICAL SHOCK, MAKE SURE TO TURN
OFF THE MAIN POWER SOURCE OR DISCONNECT POWER
DURING THE INSTALLATION OR SERVICE
OF THIS PRODUCT
Ballast must be bypassed if present.

ITEM# CL-CB100| 10000 LUMEN LED COB LED
ITEM# CL-CB100| 10000 LUMEN LED COB LED
INSTALLATION INSTRUCTIONS:
1. Before installing, make sure to shut the power OFF at the circuit breaker.
It is highly recommended that a surge protector is installed.
If Ballast is present, it must be bypassed.
2. Remove the existing bulb by unscrewing in a counter-clockwise
direction.
3. In a clockwise direction, screw in the unit. Do not overtighten as this
may cause damage to the light and/or the socket.
4. Turn the power ON at the circuit breaker.
5. Turn the light switch ON. The LEDs will illuminate.
6. To protect your eyes, never look directly into the LED lights.
If you have questions or missing parts, please contact our customer care at 1-888-745-4837 If you have questions or missing parts, please contact our customer care at 1-888-745-4837
WARNING:
RISK OF ELECTRICAL SHOCK.
TO AVOID ELECTRICAL SHOCK, MAKE SURE TO TURN
OFF THE MAIN POWER SOURCE OR DISCONNECT POWER
DURING THE INSTALLATION OR SERVICE
OF THIS PRODUCT
ADDITIONAL WARNINGS:
• DO NOT open the product. It is NOT possible to
change the LED lights or source.
• DO NOT use this product in small enclosures. It is
recommended for medium to large size rooms.
• Temperature rating is from -13OF to 104OF.
• This product is designed for dry/damp use and
is not waterproof. Never use near standing water.
• Although this product is simply screwed into a socket, it is important to
make sure no bare wires are exposed and that all wiring is insulated.
• This product is NOT to be used with dimmers. Dimmers can damage the
product and will void the warranty if used.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.Warning: Changes or modications to this unit not
expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment. Note: This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and
on, the user is encouraged to try to correct the interference by one or more of the
following measures: (1) Reorient or relocate the receiving antenna. (2) Increase
the separation between the equipment and receiver. (3) Connect the equipment
into an outlet on a circuit dierent from that of the receiver. (4) Consult the dealer
or an experienced radio/TV technician for help.