Philco GH1206S User manual

USER MANUAL
用戶手冊
GH1206S
GH1109S

2

3
Dear Customer
Thank you for buying our range hood. Please read the user manual
carefully and store in a handy place for later reference.
This hood is designed for tting in a cabinet.
Read the following carefully to avoid damage or injury.
SAFETY AND WARNINGS
●Where applicable, this appliance is supplied with xings. Please
ensure you use the correct xings suitable for the substrate where
the appliance will be installed and that they are able to support
the weight of the appliance.
●Before connecting the hood, check that the supplied voltage and
frequency match with that indicated on the appliance rating plate.
If in doubt, ask for advice instore or from a qualied installer.
●If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a safety hazard.
●Use only the same size of fittings and mounting screws as
recommended in this instruction manual. Failure to follow these
instructions may result in electrical hazards.
●Means for full disconnection must be incorporated in the fixed
wiring in accordance with the local wiring installation rules for
your country. An all-pole disconnection switch having a contact
separation of at least 3mm in all poles should be connected
during installation.
●When the extractor hood is located above an appliance, the
minimum distance between the supporting surface for the cooking
vessels on the hob and the lowest part of the hood shall be at
least 650mm.
● Consult local regulations regarding extraction outlets and ensure
these are complied with. Do not connect the hood to a ventilation
EN

4
or hot air duct containing combustion fumes from burning gas or
other fuels. Conrm that room ventilation is appropriate with the
local authorities.
●The air must not be discharged into a flue that is used for
exhausting fumes from appliances burning gas or other fuels
●The hood may stop working during an electrostatic discharge
(e.g. lightning). This involves no risk of damage. Switch off the
electricity supply to the hood and reconnect after one minute.
●This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
●This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
●Children should be supervised to ensure that they do not play
with the appliance.
●Do not install the appliance outdoors in a damp place or in an
area which may be prone to water leaks such as under or near a
sink unit. In the event of a water leak a󰀨ecting the appliance, do
not use and contact customer services to arrange for inspection.
● Do not use ammable sprays in close vicinity to the appliance.
●Please dispose of the packing material carefully. There is a
fire risk if cleaning is not carried out in accordance with the
instructions. Refer to the Care and Maintenance sections carefully
for details on how to clean and replace the aluminium and carbon
lters (if tted).
●Refer to the Care and Maintenance section for details on the type
of lamps that can be used and how to replace them.
●Do not use a steam cleaner for care and maintenance.
●The appliance is not intended to be operated by means of an

5
external timer or separate remote control system.
●There shall be adequate ventilation of the room when the hood is
used at the same time as appliances burning gas or other fuels.
Ensure that the negative pressure of the installation site does not
exceed 4 Pa (0.04 mbar) to ensure combustion fumes are not
drawn back into the room.
●Do not use the hood if it shows signs of damage or imperfection.
Contact customer services for assistance.
●Switch o󰀨 the appliance at the mains supply before carrying out
any maintenance work or cleaning.
●CAUTION: Accessible parts may become hot when used with
cooking appliances.
●Do not flambé under the hood. To avoid the risk of fire, clean
or replace the grease filter regularly and closely monitor pans
containing hot oil.
●The manufacturer declines all liability for personal or material
damage as a result of misuse or incorrect installation of this
appliance.
● The appliance is for domestic use only as an extractor hood.
INSTALLATION INSTRUCTIONS
All installation must be carried out by a competent person or
qualied electrician. Before connecting the mains supply ensure that
the mains voltage corresponds to the voltage on the rating plate.
The appliance must be connected directly to the mains using an
omnipolar circuit breaker with a minimum opening of 3mm between
the contacts.
The installer must ensure that the correct electrical connection has
been made and that it complies with the wiring diagram.
Regularly check the power plug and power cord for damage. If the
supply cord is damaged, it must be replaced by a special cord or
assembly available from the manufacturer or its service agent.
WARNING: This is a Class II appliance and MUST NOT be
earthed.

6
Contents of packaging
Rangehood
(1)
Rear Spacers
(2)
Lateral Spacer
(2)
150 to 125 adapter
(1)
Screw M6 x 40mm
(including washer)
(4)
Screw 3.5 x 10mm
(2)
Screw 3 x 12mm
(4)
Ø150mm
Ducting adapter
(1)

7
INSTALLATION
2 mm
Positioning
650mm
top of cooking
surface
Fixing dimensions
555/855
600/900
210
280
280
Rear spacer can bereversed
to suit gap at rear
160
230
150
40
272
WARNING!
Failure to install the screws or xing device in accordance with
these instructions may result in electrical hazards.

8
Drilling holes
Drill the holes on top of wooden cupboard
●drill Ø 7mm hole
●drill Ø 16mm hole
●cut Ø 196mm hole
Ø7 for hood
fastening screws 86 Ø16 for cable
clearance
Øclearance
453/753
33
210
272 252
192
196 for flue
Front of cabinet
Door/hood fascia
Fixing the ducting adapter
Connect 150mm ducting adapter to the blower outlet and use
screws to x it to the range hood.
Screw 3.5 x 10mm
Ø150mm
Ducting adapter
If necessory, connect the 150 to 125mm adapter to the Ø150mm
ducting adapter.
Important! For best performance, Ø150mm ducting is
recommended (Ø125mm ducting can be used, but will reduce
the airow of the cooker hood).

9
Fixing the Lateral spacers
Screw
3 x 12mm Lateral spacer
Mounting the rangehood to the underside of cupboard
Attach the rangehood to wooden support and x it with the 4 screws
supplied.
Cupboard
Screw M4 x 60mm and washers

10
Fixing the Rear Spacer
Use suitable Rear Spacer to cover the space between the wall and
the rangehood and x it with 2 screws.
Rear spacer
Screw 3 x 12mm
Fixing exible duct
Connect 150 mm or 125 mm exible duct to the adapter and x it.

11
OPERATING INSTRUCTIONS
Control panel features
To operate the rangehood, pull out the retractable hood and select
the extraction level using the switch on the right hand side。
High
Low
Lamp
Lamp
On
Off
Off
To switch on the rangehood light, use the switch located on the left
hand side of the rangehood.
High
Low
Lamp
Lamp
On
Off
Off
CLEANING AND MAINTENANCE
Warning: always switch off the electricity supply before
carrying out maintenance work on the hood. In the event of a
fault, contact an o󰀩cial distributor or Customer Service.
Exterior Cleaning : Use non-corrosive, liquid detergent and avoid the
use of abrasive cleaning products.
hight

12
Replacing the lamp
Ensure that the rangehood is unplugged, then slide out the
retractable hood and remove the lters. Turn the lamp anti-clockwise
to remove then replace the lamp by turning it clockwise.
10’
FUSE
OFF
High
Low
Lamp
Lamp
On
Off
Off
Cleaning Aluminium grease lters
Important! increase the lter cleaning/replacement frequency if the
hood is used for more than 2 hours a day. Always use genuine lters
from the manufacturer.
3 MONTHS
≤ 65ºC
1 MONTH

13
Replacing Activated charcoal lters
Replace Activated charcoal every 3 months
3 MONTHS
≤ 65ºC
1 MONTH
Troubleshooting
Problem Possible cause Solution
Excessive vibration. The appliance is not installed
properly on the brackets.
Take down the appliance and check
The fan blade is damaged.
Switch off the appliance. Repair to
personnel only.
The light is on, but the
fan does not work.
The fan blade is jammed.
The motor is damaged.
Both the light and
motor do not work.
Light bulb blown. Replace with a bulb of the
correct rating.
Power connection loose. Check power supply.
Suction
performance reduced.
Speed may be too low. Select a higher speed.
are dirty. Care and maintenance section).
Top vent might be
obstructed.
Clear any obstruction.
Optional vent kit might be twisted. Ensure that the vent kit
manufacturer’s instructions.
The installation may not comply with
the manufacturers instructions.
The vent hose should be correct
diameter throughout with no
reductions or restriction.(See
installation section).
Works normally but
cooking smells linger. recirculation mode or is full
of grease. maintenance section).

14
Recycling & disposal
The symbol on the product or on its packaging indicates
that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic
equipment.
By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused
by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please
contact your local city o󰀩ce, your household waste disposal service
or the shop where you purchased the product.

15

60815910.09.01.2020