Philio PAN07-1C User manual

1
PAN07-1C/-2C/-3C PAN09-1C/-2C/-3C
TWO SPDT Switch module with meter
Fig 1. PAN07 Assembling
Fig 2. PAN0 Assembling

2
This in-wall dual relay switch module is a transceiver which is a Z-Wave Plus
TM
enabled device and is fully compatible with any Z-Wave
TM
enabled network. Mini
size design let the module can easily hide itself into the wall box and that will be
good for the house decoration.
There are many kind of application by using the module to switch AC power On
and Off, one main application is the light control. The new smart relay calibration
technology can reduce the inrush current caused by the load and let the module
work perfectly with many kind of light like incandescent, fluorescent and LED
light.
This in-wall switch module is able to detect Instant power wattage and overload
current (6A with r esistive load ) of connected light or appliances. When detecting
overload state, the Module will be disabled and its On/Off button will be lockout
of which LED will flash quickly. However, disconnect and re-connect the Module
will reset its overload condition to normal status.
Adding to Z-Wave
TM
Network
In the front of casing, there is an on/off button with LED indicator below which is
used to toggle switch on and off or carry out inclusion, exclusion, reset or
association. When first power is applied, its LED flashes on and off alternately
and repeatedly at 0.5 second intervals. It implies that it has not been assigned a
node ID and start auto inclusion.
Auto Inclusion
The function of auto inclusion will be executed as long as the in wall switch does
not have Node ID and just connect the switch to main power.
Note: Auto inclusion timeout is 2 minute during which the node information of
explorer frame will be emitted once every several seconds. Unlike “inclusion”
function as shown in the table below, the execution of auto inclusion is free from
pressing the On/Off button on the Switch.
The table below lists an operation summary of basic Z-Wave functions. Please
refer to the instructions for your Z-Wave
TM
Certificated Primary Controller to
access the Setup function, and to include/exclude/associate devices
Function Description
Annotation
No node ID The Z-Wave Controller does not allocate
a node ID to the Switch. LED 2-second on, 2-second off
Inclusion 1. Put your Z-Wave controller into
inclusion mode by following the
instructions provided by the
controller manufacturer.
one press one flash LED
2. Pressing INCLUDE_BUTTON three
times within 2 seconds will enter
inclusion mode.
Exclusion 1. Put your Z-Wave controller into
exclusion mode by following the
instructions provided by the
controller manufacturer.
one press one flash LED
1. Pressing INCLUDE_BUTTON three
times within 2 seconds will enter
exclusion mode.
3. Node ID has been excluded. LED 0.5s On, 0.5s Off
(Enter auto inclusion)
Reset 1. Pressing INCLUDE_BUTTON three
times within 2 seconds will enter
inclusion mode.
Use this procedure only in
the event that the primary
controller is lost or
otherwise inoperable.
2. Within 1 second, press On/Off
button again for 5 seconds.
3. IDs are excluded. LED 0.5s On, 0.5s Off
(Enter auto inclusion)

3
Association 1. The PAN11 is an always listening
Z-Wave device, so associations
be added or removed by a controller
at any time.
Or If your controller requires to have
the PAN11 send a 'node information
frame' or NIF for associations,
pressing the On/Off button three
times within 2 seconds will cause
the PAN11 to send its NIF.
one press one flash LED
2. There are 3 groups for the switch

Including a node ID allocated by Z-Wave Controller means inclusion. Excluding a node
ID allocated by Z-Wave Controller means exclusion.
 Failed or success in including/excluding the node ID can be viewed from the Z-Wave
Controller.
Sometimes people are not easy to execute exclusion or inclusion especially
when PAN07 already installed in a wall box. To solve this issue, PAN07 support
a special feature that can use S1 or S2 to execute exclusion, inclusion, Reset or
Association” at the first 3 minutes when first time connect to main power. PAN09
does not support S1/S2 function.
LED Indication
To distinguish what mode the switch is in, view from the LED for identification.
State Type LED Indication
Normal Whatever we switch On and off of the PAN07/PAN09 by S1 S2 or
On/Off button or RF command, the LED will lights up 1 second and
then off.
No node ID Under normal operation, when the Switch has not been allocated a
node ID, the LED flashes on and off alternately at 2-second
intervals. By pressing S1 S2 or On/Off button, it will stop flashing
temporarily.
Learning When PAN07/PAN09 is in learning mode, LED flashes on and off
alternately and repeatedly at 0.5 second intervals.
Overload When overload state occurs, the Switch is disabled of which LED
flashes on and off alternately at 0.2 second intervals. Overload
state can be cleared by disconnect and reconnect the Switch to the
main power
Choosing a Suitable Location
1. Do not locate the Switch facing direct sunlight, humid or dusty place.
2. The suitable ambient temperature for the Switch is 0°C~40°C.
3. Do not locate the Switch where exists combustible substances or any
source of heat, e.g. fires, radiators, boiler etc.
4. After putting it into use, the body of Switch will become a little bit hot of
which phenomenon is normal.
Installation
1. Put in wall switch into a wall box and connect the AC power wire L,N to
PAN07/PAN09 connector L, N.
2. Connect the wall switch to the PAN07/PAN09 as Fig1/Fig2 .

4
3. To manually turn ON the Switch, press and release the On/Off button. The
LED will light ON for 1 second, and the load plugged into the Switch will
also turn ON.
4. To manually turn OFF the Switch, simply press and release the On/Off
button. The LED will light ON for 1 second and the load plugged into the
Switch will turn OFF.
Programming
1. Basic Command Class / Binary Switch Command Class
The Switch will respond to BASIC and BINARY SWITCH commands that
are part of the Z-Wave system.
1-1 BASIC_GET / BINARY_SWITCH_GET
Since the switch have two relay, the Switch will report its On/Off state to
the Controller by setting Configuration parameter 3.
Configuration parameter 3=1(default)
Report ON when either relay 1 ON or relay 2 ON
Report OFF when both relay 1 and relay 2 OFF
Configuration parameter 3=2 Report ON when relay 1 ON
Report OFF when relay 1 OFF
Configuration parameter 3=3 Report ON when relay 2 ON
Report OFF when relay 2 OFF
Basic Get Command: [Command Class Basic, Basic Get]
Basic Report Command:
Report OFF: [Command Class Basic, Basic Report, Value = 0(0x00)]
Report ON:[Command Class Basic, Basic Report, Value = 255(0xFF)]
Binary Switch Get Command:[Command Class Switch Binary, Switch
Binary Get]
Binary Switch Report Command:
Report OFF:[Command Class Switch Binary, Switch Binary Report, Value
=0(0x00)]
Report ON:[Command Class Switch Binary, Switch Binary Report, Value
= 255(0xFF)]
Note: If the BASIC_GET/SWITCH_GET command follow the switch On/Off
command, it should add 0.5s time delay before the Get command.
1-2 BASIC_SET / SWITCH_BINARY_SET
Since the switch has two relay, the load attached to the Switch will turn on
or off upon receipt of the following commands from a Z-Wave Controller by
setting Configuration parameter 3.
Configuration parameter 3=1(default) switch ON and OFF both relay 1
and relay 2
Configuration parameter 3=2 switch ON and OFF of relay 1
Configuration parameter 3=3 switch ON and OFF of relay 2
[Command Class Basic, Basic Set, Value = 1~99, 255(0xFF)]: the load
attached to the Switch turns on.
[Command Class Basic, Basic Set, Value = 0(0x00)]: the load attached to
the Switch turns off.
[Command Class Switch Binary, Switch Binary Set, Value = 1~99,
255(0xFF)]: the load attached to the Switch turns on.
[Command Class Switch Binary, Switch Binary Set, Value = 0(0x00)]: the
load attached to the Switch turns off.
1. Z-Wave’s Groups (Association Command Class Version 2)
The Switch can be set to send reports to control associated Z-Wave devices. It
supports 3 association groups which every group has one node support.
Group1~Group3 support SWITCH_BINARY_REPORT,
METER_REPORT_COMMAND_V3
For group 1, the Switch will report (1) ON/OFF status of Relay1 and Relay2 (2)
Instant Power Consumption (Watt) of Relay1 and Relay2 (3) Accumulated
Power Consumption (KWh) of Relay1 and Relay2 to Z-Wave Controller.

5
For group 2, the Switch will report (1) ON/OFF status of Relay1 (2) Instant
Power Consumption (Watt) of Relay1 (3) Accumulated Power Consumption
(KWh) of Relay1 to Z-Wave Controller.
For group 3, the Switch will report (1) ON/OFF status of Relay2 (2) Instant
Power Consumption (Watt) of Relay2 (3) Accumulated Power Consumption
(KWh) of Relay2 to Z-Wave Controller.
2-1 Auto report to Grouping 1 ~3(Maximum Node 1)
2-1-1 On/Off Event Report
When “on” or “off” state has been changed, it will send Binary Switch Report
to the nodes of Group1~3.
Binary Switch Report
ON:[Command Class Switch Binary, Switch Binary Report, Value
=255(0xFF)]
OFF:[Command Class Switch Binary, Switch Binary Report, Value
=0(0x00)]
2-1-2 Instant Power Consumption vary over 5% report
When the power consumption of load vary over 5%, it will send Meter report
to the nodes of Group
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01，Precision = 1，Scale = 0x02，Size = 4，Meter Value(W) ]
2-1-3 overload alarm report command
When PAN07/PAN09 detect the overload , it will send Alarm Report to the
correspond Group。
The content of Alarm Report
Alarm report command: [Command_Class_Alarm, Alarm_Report, Alarm Type =
[Command_Class_Alarm, Alarm_Report, Alarm Type = [Command_Class_Alarm, Alarm_Report, Alarm Type =
[Command_Class_Alarm, Alarm_Report, Alarm Type =
0x08, Alarm Level = 0xFF]
0x08, Alarm Level = 0xFF]0x08, Alarm Level = 0xFF]
0x08, Alarm Level = 0xFF]
2-2 Response to Meter Get Command
The Switch will report its (1) instant Power Consumption (Watt) or (2)
accumulated power consumption(KWH) or (3) AC load Voltage (V) or (4) AC
load current ( I ) (5) load power factor (PF) to Z-Wave Controller after
receive the Meter Get Command from Z-Wave Controller.
2-2-1 Instant Power Consumption (Watt) of Switch
When receiving Meter Get Command, it will report Meter Report Command
to the node asked.
Meter Get Command: [Command Class Meter, Meter Get, Scale
=0x02(W)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01，Precision = 1，Scale = 0x02，Size = 4，Meter Value(W) ]
Example:
Meter Value 1 = 0x00 (W)
Meter Value 2 = 0x00 (W)
Meter Value 3 = 0x03 (W)
Meter Value 4 = 0xEA (W)
Meter(W) = Meter Value 3 *256 + Meter Value 4 = 100.2W
2-2-2 Accumulated Power Consumption (KW/h)
When receiving Meter Get Command, it will report Meter Report
Command to the node asked.
Meter Get Command:
[Command Class Meter, Meter Get, Scale = 0x00 KW/h)]

6
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01， Meter Type
=0x01， Precision = 2，Scale = 0x00，Size = 4，Meter Value (KWh)]
Example:
Scale = 0x00 (KWh)
Precision = 2
Size = 4 Bytes (KW/h)
Meter Value 1 = 0x00(KWh)
Meter Value 2 = 0x01(KWh)
Meter Value 3 = 0x38(KWh)
Meter Value 4 = 0xA3(KWh)
Accumulated power consumption (KW/h) = (Meter Value 2*65536) +
(Meter Value 3*256) + (Meter Value 4) = 800.35 (KW/h)
2-2-3 Clearing accumulated power consumption
Whenever re-start counting the accumulated power consumption is needed,
you can use Meter Reset Command to clear it.
Meter Reset Command: [Command Class Meter, Meter Reset]
2-2-4 AC load Voltage (V)
When receiving Meter Get Command, it will report Meter Report Command
to the node asked.
Meter Get Command: [Command Class Meter, Meter Get, Scale =0x04(V)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01，Precision = 1，Scale = 0x04，Size = 2， Meter Value(V)]
Example:
Scale = 0x04 (V)
Precision = 1
Size = 2 (2 Bytes of V)
Meter Value 1 = 0x09(V)
Meter Value 2 = 0x01(V)
AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.5 (V)
2-2-5 AC load current ( I )
When receiving Meter Get Command, it will report Meter Report Command to
the node asked.
Meter Get Command: [Command Class Meter, Meter Get, Scale =0x05(I)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01，Precision = 2，Scale = 0x05，Size = 2，Meter Value(I)]
Example:
Scale = 0x05 (I)
Precision = 2
Size = 2 (2 Bytes of I)
Meter Value 1 = 0x01(I)
Meter Value 2 = 0x21(I)
AC load current = (Meter Value 1*256) +(Meter Value 2)= 2.89 (A)
2-2-6 load power factor (PF)
When receiving Meter Get Command, it will report Meter Report Command to
the node asked.
Meter Get Command: [Command Class Meter, Meter Get, Scale =0x06(PF)]
Meter Report Command:

7
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01， Precision = 2，Scale = 0x06，Size = 1 Bytes，Meter Value(PF)]
Example:
Scale = 0x06 (PF)
Precision = 2
Size = 1 (1 Byte of PF)
Meter Value 1 = 0x63(PF) (It means that the load power factor is 0.99)
2-3 Multi Channel Command Class Version 3
PAN07/PAN09 also support Muti Channel command class (version 3), which
include BINARY_SWITCH_GET, BINARY_SWITCH_SET, BASIC_GET,
BASIC_SET, METER_SUPPORTED_GET, METER_RESET, METER_GET.
You may control or get report from 3 endpoints of PAN07/PAN09.
2-3-1 BINARY_SWITCH_GET
You may get the ON/OFF state from every endpoint, when endpoint set to 1 ,
PAN07/PAN09 will reply ON(0xFF) either Relay 1 or Relay2 is ON, report
OFF (0x00) when both Relay 1 and Relay2 OFF. If endpoint set to 2,
PAN07/PAN09 will reply state of Relay1 . If endpoint set to 3 and
PAN07/PAN09 will reply state of Relay2
Below is an example show a source endpoint 5 send a get command to
PAN07/PAN09 endpoint 1
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x05 (this is the endpoint of command owner
here we assume endpoint is 5，
if the
owner doesn’t support multi
Channel this value will be 0)
(Bit Address+Destination End Point = 0x01)
(Bit Address =0；Destination End Point
range from 1~3)
Command Class = 0x25 (Command_Class_Switch_Binary =
0x25)
Command =0x02 (Switch_Binary_Get = 0x02)
Below is the example show PAN07/PAN09 report to last command
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x01 Since the endpoint is 1 so PAN07
/PAN09 will reply ON(0xFF) either Relay
1 or Relay2 is ON, report OFF (0x00)
when both Relay 1 and Relay2 OFF
(Bit Address+Destination End Point = 0x05)
(Bit Address =0；Destination End Point)
Command Class = 0x25 (Command_Class_Switch_Binary =
0x25)

8
Command =0x03 (Switch_Binary_Reportet = 0x3)
Parameter 1 = 0xFF (ON=0xFF ，OFF=0x00)
Note: If the Multi-Channel Encapsulated BASIC_GET/SWITCH_GET
command follow a switch On/Off command, it should add 0.5s time
delay before the Get command.
2-3-2 BINARY_SWITCH_SET
By using BINARY_SWITCH_SET Command of Multi Channel Command Class
Encapsulation Command, you can switch both Relay1 and Relay2 ON/OFF by
setting endpoint to 1 or switch Relay1 ON/OFF by setting endpoint to 2 or switch
Relay2 ON/OFF by setting endpoint to 3
The example of the command show that switch off relay1 of PAN07/PAN09
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x01 (this is the endpoint of command owner
here we assume endpoint is 1，if the
owner doesn’t support multi Channel
this value will be 0)
(Bit Address+Destination End Point = 0x02)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x25 (Command_Class_Switch_Binary =
0x25)
Command =0x01 (Switch_Binary_Set = 0x01)
Parameter 1 = 0x00 (ON=0xFF ，OFF=0x00)
2-3-3 METER_SUPPORTED_GET：
：：
：
This command is to ask the endpoint of PAN07/PAN09 what kind of meter data
can be reported
The example show how to get the meter report type
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x01 (this is the endpoint of command owner
here we assume endpoint is 1，if the
owner doesn’t support multi Channel
this value will be 0)
(Bit Address+Destination End Point = 0x03)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x03 (Meter_Supported_Get = 0x03)

9
Below is the example show PAN07/PAN09 report to last command
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x03
(Bit Address+Destination End Point = 0x01)
Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)
Command =0x04 (Meter_Supported_Report = 0x04)
Parameter 1 = 0x81 (Meter Reset =1 ，Meter Type=0x01)
Parameter 2 = 0x75 (Scale Supported =
KWh+W+V+A+Power Factor = 0x75)
2-3-4 METER_RESET
This command is to reset the Accumulated Power Consumption (KWh) to 0
The example show how to reset the KWh
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x03
(this is the endpoint of command owner,
here we assume endpoint is 3，if the
owner doesn’t support multi Channel
this value will be 0)
(Bit Address+Destination End Point = 0x01)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x05 ( Meter_Reset = 0x05)
2-3-5 METER_GET：
：：
：
Using meter get command to get the KWH,W,V,I,PF from endpoint of
PAN07/PAN09
2-3-5-1 Get KWH from endpoint
Meter_GET example:
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x05
(this is the endpoint of command owner,
here we assume endpoint is 5，if the
owner doesn’t support multi Channel
this value will be 0)
(Bit Address+Destination End Point = 0x03)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x01 (Meter_Get = 0x01)

10
Parameter 1 = 0x00 (Scale = KWH = 0x00)
Accumulated power consumption (KWH) Report example：
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x03 (Meter report = Endpoint3)
(Bit Address+Destination End Point = 0x05)
(Bit Address =0；
Destination End Point =
command owner Endpoint value)
Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)
Command =0x02 (Meter_Report = 0x02)
Parameter 1 = 0x21 (Scale Bit2 = 0 ，Rate Type = 0x01，
Meter Type=0x01)
Parameter 2 = 0x44 (Precision = 2，Scale Bit1Bit0 = 0，
Size =
4)
Parameter 3 = 0x00 Accumulated Power Consumption =
0x000005FD = 15.33 KWh
Parameter 4 = 0x00
Parameter 5 = 0x05
Parameter 6 = 0xFD
2-3-5-2 Get Instant Power Consumption (Watt) from endpoint
METER_GET example：
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x05 (this is the endpoint of command owner,
here we assume endpoint is 5，
if the owner
doesn’t support multi Channel this value
will be 0)
(Bit Address+Destination End Point =
0x03)
(Bit Address =0；Destination End Point
range 1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x01 (Meter_Get = 0x01)
Parameter 1 = 0x10 (Scale = W = 0x02)
PAN07/PAN09 Instant Power Consumption (W) Report example：
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x03 (Meter report = Endpoint3)

11
(Bit Address+Destination End Point = 0x05)
(Bit Address =0；
Destination End Point =
command owner Endpoint value)
Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)
Command =0x02 (Meter_Report = 0x02)
Parameter 1 = 0x21 (Scale Bit2 = 0 ，Rate Type = 0x01，
Meter Type=0x01)
Parameter 2 = 0x34 (Precision = 1，Scale Bit1Bit0 = 0x02，
Size = 4)
Parameter 3 = 0x00 Instant Power Consumption =
0x000003EA
= 100.2W
Parameter 4 = 0x00
Parameter 5 = 0x03
Parameter 6 = 0xEA
2-3-5-3 Get load voltage V from endpoint
Meter_GET example:
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x05 (this is the endpoint of command owner,
here we assume endpoint is 5，
if the owner
doesn’t support multi Channel this value
will be 0)
(Bit Address+Destination End Point =
0x03)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x01 (Meter_Get = 0x01)
Parameter 1 = 0x20 (Scale = V = 0x04)
PAN07/PAN09 AC load Voltage report example：
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x03 (Meter report = Endpoint3)
(Bit Address+Destination End Point = 0x05)
(Bit Address =0；
Destination End Point =
command owner Endpoint value)
Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)
Command =0x02 (Meter_Report = 0x02)
Parameter 1 = 0xA1 (Scale Bit2 = 1 ，Rate Type = 0x01，
Meter Type=0x01)

12
Parameter 2 = 0x22 (Precision = 1，Scale Bit1Bit0 = 0x00，
Size = 2)
Parameter 3 = 0x09 Voltage = 0x0910 = 232.0V
Parameter 4 = 0x10
2-3-5-4 Get load current I from endpoint
Meter_GET example:
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x05 (this is the endpoint of command owner,
here we assume endpoint is 5，
if the owner
doesn’t support multi Channel this value
will be 0)
(Bit Address+Destination End Point =
0x03)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x01 (Meter_Get = 0x01)
Parameter 1 = 0x28 (Scale = A = 0x05)
PAN07/PAN09 AC load current (I) example：
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x03 (Meter report = Endpoint3)
(Bit Address+Destination End Point = 0x05)
(Bit Address =0；
Destination End Point =
command owner Endpoint value)
Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)
Command =0x02 (Meter_Report = 0x02)
Parameter 1 = 0xA1 (Scale Bit2 = 1 ，Rate Type = 0x01，
Meter Type=0x01)
Parameter 2 = 0x4A (Precision = 2，Scale Bit1Bit0 = 0x01，
Size = 2)
Parameter 3 = 0x00 Current = 0x002B = 0.43A
Parameter 4 = 0x2B
2-3-5-5 Get power factor PF from endpoint
Meter_GET example:
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP

13
Source End Point = 0x05 (this is the endpoint of command owner,
here we assume endpoint is 5，
if the owner
does not support multi Channel this value
will be 0)
(Bit Address+Destination End Point =
0x03)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x01 (Meter_Get = 0x01)
Parameter 1 = 0x30 (Scale = PF = 0x06)
PAN07/PAN09 power factor report example：
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x03 (Meter report = Endpoint3)
(Bit Address+Destination End Point =
0x05)
(Bit Address =0；Destination End Point =
command owner Endpoint value)
Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)
Command =0x02 (Meter_Report = 0x02)
Parameter 1 = 0xA1 (Scale Bit2 = 1 ，Rate Type = 0x01，
Meter Type=0x01)
Parameter 2 = 0x51 (Precision = 2，Scale Bit1Bit0 = 0x10，
Size
= 1)
Parameter 3 = 0x63 Power Factor = 0x63 = 0.99
2. Z-Wave’s Configuration
Configuration
Parameter Function Size (Byte) Value Unit Default
Description
1 Watt Meter
Report
Period
2 0x01-
0x7FFF 5s 720 720*5s=3600s=1 hour
2 KWH
Meter
Report
Period
2 0x01-
0x7FFF 10min
6 6*10min= 1 hour
3 Slected
Relay
1 1-3 3 1：Relay1
2：Relay2
3：Relay1 &
Relay2
4 Edge or
Pulse
mode or
Edge-Toggl
e mode
1 1-3 1 1：Edge mode
2：Pulse mode
3：Edge-
Toggle
mode
5 Threshold
of current
for Load
Caution
2 10-600 0.01A 600
600*0.01A = 6.0A
6 Threshold 2 1-10000 1KWh 10000

14
of KWH for
Load
Caution
7 Relay
control
mode
1 1-2 1 1 : Control relay
refer to meter
wattage
2 : Control relay
directly
8 Restore
Relay state
mode
1 0-2 1 0 : All relay stay
NC terminal
1 : Last relay
switch state
2 : All relay stay
NO terminal
9 Existence
of
Endpoint3
1 1-2 1 1 : Endpoint3 exist
2 : No Endpoint3
3-1 Watt Meter Report Period:
If the setting is configured for 1hour (set value =720), the PAN07/PAN09 will
report its instant power consumption every 1 hour to the node of correspond
Group. The maximum interval to report its instant power consumption is 45
hours (5s*32767/3600=45hr).
3-2 KWH Meter Report Period:
If the setting is configured for 1hour (set value =6), the PAN07/PAN09 will
report its Accumulated Power Consumption (KW/h) every 1 hour to the node
of correspond Group. The maximum interval to report its Accumulated
Power Consumption (KW/h) is 227.55 days (10min*32767/1440=227.55
days).
3-3 Selected Relay
If Controller not using Multi_Channel command class to access the relay of
PAN07/PAN09, you may configure the value of relay to react the Basic
Command Class 、Binary Switch Command Class or Meter Command Class
V3
3-3-1 Selecte Relay1 and Relay2：
：：
：Default select is 3
Set command Relay state
Basic_Set or Binary_Switch_Set ON
Relay1 ON &
Relay2 ON
Basic_Set or Binary_Switch_Set OFF
Relay1 OFF &
Relay2 OFF
Get command Relay state Report to command sender
Basic_Get or Binary_Switch_Get
Relay1 ON or
Relay2 ON ON
Basic_Get or Binary_Switch_Get Relay1 OFF &
Relay2 OFF
OFF
Get command parameter Report to command inquirer
Meter_Get KWh Relay1 KWh1+Relay2 KWh2
Meter_Get
Watt Relay1 W1+Relay2 W2
Meter_Get
Voltage Relay1 and Relay2 are the same
voltage
Meter_Get
Current Relay1 I1+Relay2 I2
Meter_Get Power factor PF Only Relay1
3-3-2 Selected Relay 1
Only relay1 can be controlled and report.
3-3-3 Selected Relay 2
Only relay2 can be controlled and report.

15
3-4 Edge and Pulse mode
Manual switch S1 and S2 can set to Edge mode or Pulse mode or Edge-Toggle
mode, default value is Edge mode. But this parameter is useless to PAN09.
3-4-1 Edge mode: this mode is suitable for the bi stable wall switch that has
indicator point on the switch, and the same position correspond to same
state of relay1 and relay2. if the PAN07 relay change the state because
of receiving Z-Wave RF command, it may need two times of change
(switch on to off or switch off to on) to let relay back to the correspond
state.
3-4-2 Pulse mode: this mode is suitable for the toggle type wall switch to swap
the state of Relay1 or Relay2
3-4-3 Edge-Toggle mode: this mode is suitable for the normal bi-stable switch,
every time when change the state of the wall switch will also swap the
state of Relay1 or Relay2
3-5 Threshold of current for Load Caution
This is a warning when the current of load over the preset threshold value, if the
setting value is 600 (6A), when the load current of Relay1 over this value,
PAN07/PAN09 will send current meter report to the node of correspond Group,
the Range of the setting value is from 10 to 600, and the default value is 600
(6A).
3-6 Threshold of KWh for Load Caution
This is a warning when the KWh of load over the preset threshold value, If the
setting value is 10000, when the Accumulated Power Consumption of Relay1 or
Relay2 over this value, PAN07/PAN09 will send KWh Meter Report command to
the node of correspond Group, minimum value is 1KWh and default value is
10000 kWh.
3-7 Relay control mode
3-7-1 Relay controlling is referred to the meter wattage: When PAN07/PAN09
gets an instruction from RF command or the manual switch, to switch on
or off, it will check the wattage of the load first. If the wattage value is
greater than 2 watts, the switch state means ON; on the other hand, it
means OFF. When the switch state is ON, only SWITCH OFF instruction
will be accept; on the other hand, when the switch state is OFF, only
SWITCH ON instruction will be accept.
3-7-2 Control relay directly : Whenever PAN07/PAN09 get an SWITCH ON
instruction, it will close the relay; on the other hand, it will open the relay.
3-8 Restore switch state mode
Whenever the AC power return from lost, PAN07/ PAN09 will restore the relay
switch state which could be All relay stay NC terminal、Last relay switch state、
All relay stay NO terminal. The default setting is Last relay switch state.
3-9 Existence of Endpoint3：
：：
：
The endpoint3 of Multi-Channel Command Class is related to relay1 and relay2.
It may be redundant for the need to control relay1 or relay2 individually. When
the Existence of Endpoint3 is set as 0, the endpoint3 of Multi-Channel

16
Command Class will be disabled. The default value is 1.
4. Protection Command Classes
PAN07/ PAN09 supports Protection Command Class version 2, it can protect
the switch against unintentionally control by e.g. a child. And it can also protect
the switch from being turned off by setting it in “No RF Control” state.
After being set to “Protection by sequence” state, any intentional pressing of
On/Off button or S2/S2 should be hold longer than 1 second, or the switch state
will not change. However, the operation of learn function does not change,
because learning will not be protected.
5. Firmware update over the air (OTA)
PAN07/PAN09 is based on 500 series SoC and supports Firmware Update
Command Class, it can receives the updated firmware image sent by controller
via the Z-wave RF media. It is a helpful and convenient way to improve some
function if needed.
6. Command Classes
The Switch supports Command Classes including…
* COMMAND_CLASS_ZWAVEPLUS_INFO
* COMMAND_CLASS_VERSION_V2
* COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
* COMMAND_CLASS_DEVICE_RESET_LOCALLY
* COMMAND_CLASS_ASSOCIATION_V2
* COMMAND_CLASS_ASSOCIATION_GRP_INFO
* COMMAND_CLASS_POWERLEVEL
* COMMAND_CLASS_SWITCH_BINARY
* COMMAND_CLASS_BASIC
* COMMAND_CLASS_SWITCH_ALL
* COMMAND_CLASS_ALARM
* COMMAND_CLASS_SCENE_ACTIVATION
* COMMAND_CLASS_SCENE_ACTUATOR_CONF
* COMMAND_CLASS_PROTECTION
* COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
* COMMAND_CLASS_MULTI_CHANNEL_V3
* COMMAND_CLASS_METER_V3
* COMMAND_CLASS_CONFIGURATION
Troubleshooting
Symptom
Cause of Failure
Recommendation
The Switch not working and
LED off 1. The Switch is not connect to the Main
power
2. The Switch break
down
1. Check power connections
2. Don’t open up the Switch and
send it for repair.
The Switch LED
illuminating, but cannot
control the ON/OFF
Switch of the load attached
Check if the load connect
into the Switch has its
own ON/OFF switch
Set the ON/OFF switch of the load
attached to ON
The Switch LED
illuminating, but the
Detector cannot control
the Switch
1. Not carry out
association
2. Same frequency
interference
1. Carry out association
2. Wait for a while to re-try
LED keep flashing, but
cannot control Overload occurs Remove the load attached or check max. load cannot exceed
6A(Resistive load)
Specification
Operating Voltage 100 ~240VAC /50Hz/60Hz
Maximum Load 5A(230Vac/120Vac) (Resistive load)
Range Minimum 40 m in door 100m outdoor line of sight
Operating Temperature 0°C ~ 40°C
Frequency Range
PAN07 - 1/PAN09-1: 868.40MHz; 869.85MHz(EU) /
PAN07-2/PAN09-2: 908.40MHz; 916.00MHz(USA/Canada) /
PAN07-3/PAN09-3: 922.5MHz/ 923.9MHz/ 926.3MHz (Taiwan/JP)
** Specifications are subject to change and improvement without notice.

17
FCC ID : RHHPAN07
Warning:
1.Plug out to disconnect from power supply; Do not plug in line.
2. Do not exceed the max rating
Disposal
This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible harm to
the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.
Company of License Holder：Philio Technology Corporation
Address of License Holder：8F.,No.653-2,Zhongzheng Rd., Xinzhuang Dist.,
New Taipei City 24257,Taiwan(R.O.C)
FCC Interference Statement
FCC Interference StatementFCC Interference Statement
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC ules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
• eorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC ules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.