Philio PAN03 User manual

PAN03 ; PAN10
Switch Module with meter
Fig 1. PAN03 Assembling
1

Fig 2. PAN10 Assembling
This plug-in ON/OFF switch PAN03/PAN10 is a security enabled wireless switch,
based on -Wave Plus technology. -Wave PlusTM enabled devices displaying the -
Wave PlusTM logo can also be used with it regardless of the manufacturer, and can
also be used in other manufacturer’s -WaveTM enabled networks. Remote On/Off
control of the connected load is possible with other manufacturer’s wireless
Controller. Each switch is designed to act as a repeater. Repeaters will re-transmit
the RF signal to ensure that the signal is received by its intended destination by
routing the signal around obstacles and radio dead spots. Because PAN03/PAN10
supports Security Command Class, it can learn with Secured controller. Its
functionality and supported command classes is identical when included as a secure
and non-secure device.
This plug-in ON/OFF switch is able to detect instance wattage and overload current
(12A with resistive load) of connected lights or appliances. When detecting overload
state, the Switch will be disabled and its On/Off button will be lockout of which LED
will flash quickly. However, unplug and re-connect the switch will reset its overload
condition to normal status.
Adding to Z-WaveTM Network
In the front casing, there is an On/Off button with LED indicator which is used to
toggle switch on and off or carry out inclusion, exclusion, reset or association. When
first power is applied, its LED flashes on and off alternately and repeatedly at 0.5
second intervals. It implies that it has not been assigned a node ID and start auto
inclusion.
Auto nclusion
The function of auto inclusion will be executed as long as the switch does not have
Node ID and just plug the switch into a wall outlet.
Note: Auto inclusion timeout is 2 minute during which the node information of
explorer frame will be emitted once several seconds. Unlike “inclusion” function as
shown in the table below, the execution of auto inclusion is free from pressing the
On/Off button on the Switch.
The table below lists an operation summary of basic -Wave functions. Please refer
to the instructions for your -WaveTM Certificated Primary Controller to access the
Setup function, and to Add/Remove/associate devices
Function Description Annotation
No node ID The -Wave Controller does not allocate
a node ID to the Switch.
2-second on, 2-second off
Add
(Inclusion)
1. Put your -Wave controller into
inclusion mode by following the
instructions provided by the
controller manufacturer.
2

2. Pressing On/Off button three times
within 2 seconds will enter inclusion
mode.
Remove
(Exclusion)
1. Put your -Wave controller into
exclusion mode by following the
instructions provided by the
controller manufacturer.
2. Pressing On/Off button three times
within 2 seconds will enter exclusion
mode.
Node ID has been excluded. 0.5s On, 0.5s Off (Enter
auto inclusion)
Reset 1. Pressing On/Off button three times
within 2 seconds will enter inclusion
mode.
Use this procedure only in
the event that the primary
controller is lost or
otherwise inoperable.
2. Within 1 second, press On/Off
button again for 5 seconds.
3. IDs are excluded. 0.5s On, 0.5s Off (Enter
auto inclusion)
Association 1. The PAN03 is an always listening
-Wave device, so associations
may
be added or removed by a controller
at any time.
Or If your controller requires to have
the PAN03 send a 'node information
frame' or NIF for associations, then
pressing the On/Off button three
times within 2 seconds will cause
the PAN03 to send its NIF.
2. There are only one group for the
switch
Adding a node ID allocated by -Wave Controller means inclusion. Removing a node
ID allocated by -Wave Controller means exclusion.
Failed or success in including/excluding the node ID can be viewed from the -Wave
Controller.
Sometimes people are not easy to execute exclusion or inclusion especially when
PAN03 already installed in a wall box. To solve this issue, PAN03 support a special
feature that can use S1 or S2 to execute “exclusion, inclusion, Reset or Association”
at the first 3 minutes when first time connect to main power. PAN10 does not support
S1/S2 function.
3

LED ndication
To distinguish what mode the switch is in, view from the LED for identification.
State Type LED ndication
Normal Whenever we switch On and off of the PAN03/PAN10 by S1 S2 or
On/Off button or RF command, the LED will lights up 1 second
and then off.
No node ID Under normal operation, when the Switch has not been allocated a
node ID, the LED flashes on and off alternately at 2-second inter-
vals. By pressing S1 S2 or On/Off button, it will stop flashing tem-
porarily.
Learning When PAN03/PAN10 is in learning mode, LED flashes on and off
alternately and repeatedly at 0.5 second intervals.
Overload When overload state occurs, the Switch is disabled of which LED
flashes on and off alternately at 0.2 second intervals. Overload
state can be cleared by unplugging and reconnecting the Switch to
the wall outlet.
Choosing a Suitable Location
1. Do not locate the Switch facing direct sunlight, humid or dusty place.
2. The suitable ambient temperature for the Switch is 0°C~40°C.
3. Do not locate the Switch where exists combustible substances or any source of
heat, e.g. fires, radiators, boiler etc.
4. After putting it into use, the body of Switch will become a little bit hot of which
phenomenon is normal.
nstallation
1. Put the in wall switch into a wall box and connect the AC power wire L,N to
PAN03/PAN10 connector L, N.
2. Connect the wall switch to the PAN03/PAN10 as Fig1.
3. There are 3 mode PAN03/PAN10 can be configured to match different kind of
wall switch,
please refer to 3-10 Edge / Pulse / Edge-Toggle mode which described in next
section of this user manual.
Programming
1. Basic Command Class / Binary Switch Command Class
The Switch will respond to BASIC and BINARY commands that are part of the -
Wave system.
1-1 BASIC_GET / BINARY_SWITCH_GET
Upon receipt of the following commands from a -Wave Controller, the Switch will
report its On/Off state to the node asked.
Basic Get Command: [Command Class Basic, Basic Get]
Basic Report Command:
Report OFF: [Command Class Basic, Basic Report, Value = 0(0x00)]
4

Report ON:[Command Class Basic, Basic Report, Value = 255(0xFF)]
Binary Switch Get Command:[Command Class Switch Binary, Switch
Binary Get]
Binary Switch Report Command:
Report OFF:[Command Class Switch Binary, Switch Binary Report, Value
=0(0x00)]
Report ON:[Command Class Switch Binary, Switch Binary Report, Value
= 255(0xFF)]
1-2 BASIC_SET / SWITCH_BINARY_SET
Upon receipt of the following commands from a -Wave Controller, the load
attached to the Switch will turn on or off.
[Command Class Basic, Basic Set, Value = 1~99,255(0xFF)]: the load
attached to the Switch turns on.
[Command Class Basic, Basic Set, Value = 0(0x00)]: the load attached to
the Switch turns off.
[Command Class Switch Binary, Switch Binary Set, Value = 1~99,
(255)0xFF]: the load attached to the Switch turns on.
[Command Class Switch Binary, Switch Binary Set, Value = 0(0x00)]: the
load attached to the Switch turns off.
1. Z-Wave’s Groups (Association Command Class Version 2)
The Switch can be set to send reports to associated -Wave devices. It supports
one association group with one node support for Grouping 1. For group 1, the Switch
will report its latest status to -Wave Controller.
Grouping 1 includes, SWITCH_BINARY_REPORT, METER_REPORT,
ALARM_REPORT.
2-1 Auto report to Grouping 1 (Maximum Node 1)
2-1-1 On/Off Event Report
When “on” or “off” state has been changed, it will send Binary Switch Report to the
node of Grouping 1.
Binary Switch Report
ON:[Command Class Switch Binary, Switch Binary Report, Value
=255(0xFF)]
OFF:[Command Class Switch Binary, Switch Binary Report, Value
=0(0x00)]
2-1-2 Instant Power Consumption vary over 5% report
When the power consumption of load vary over 5%, it will send Meter report to the
nodes of Grouping 1.
Meter Report Command:
5

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01，Precision = 1，Scale = 0x02，Size = 4，Meter Value(W) ]
2-1-3 Overload alarm report
When PAN03/PAN10 detects the current is more than 12A, it will send Alarm
Report to Group 1 node.
The content of Alarm Report
Alarm report command: [Command_Class_Alarm, Alarm_Report, Alarm Type = 0x08,
Alarm Level = 0xFF]
2-2 Response to Meter Get Command
The Switch will report its (1) instant Power Consumption (Watt) or (2) accumulated
power consumption(KWH) or (3) AC load Voltage (V) or (4) AC load current ( I )
(5) load power factor (PF) to -Wave Controller after receive the Meter Get
Command from -Wave Controller.
2-2-1 Instant Power Consumption (Watt) of Switch
When receiving Meter Get Command, it will report Meter Report Command to the
node.
Meter Get Command: [Command Class Meter, Meter Get, Scale =0x02(W)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01，Precision = 1，Scale = 0x02，Size = 4，Meter Value(W) ]
Example:
Meter Value 1 = 0x00 (W)
Meter Value 2 = 0x00 (W)
Meter Value 3 = 0x03 (W)
Meter Value 4 = 0xEA (W)
Meter(W) = Meter Value 3 *256 + Meter Value 4 = 100.2W
2-2-2 Accumulated Power Consumption (KW/h)
When receiving Meter Get Command, it will report Meter Report Command to
the node.
Meter Get Command: [Command Class Meter, Meter Get, Scale = 0x00 KW/h)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01 ，Meter Type =
0x01 ，Precision = 2，Scale = 0x00，Size = 4，Meter Value (KWh)]
Example:
Scale = 0x00 (KWh)
Precision = 2
Size = 4 Bytes (KW/h)
Meter Value 1 = 0x00(KWh)
Meter Value 2 = 0x01(KWh)
Meter Value 3 = 0x38(KWh)
Meter Value 4 = 0xA3(KWh)
Accumulated power consumption (KW/h) = (Meter Value 2*65536) + (Meter Value
3*256) + (Meter Value 4) = 800.35 (KW/h)
6

2-2-3 Clearing accumulated power consumption
Whenever re-start counting the accumulated power consumption is needed, you
can use Meter Reset Command to clear it.
Meter Reset Command: [Command Class Meter, Meter Reset]
2-2-4 AC load Voltage (V)
When receiving Meter Get Command, it will report Meter Report Command to the
node.
Meter Get Command: [Command Class Meter, Meter Get, Scale =0x04(V)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01，Precision = 1，Scale = 0x04，Size = 2 ，Meter Value(V)]
Example:
Scale = 0x04 (V)
Precision = 1
Size = 2 (2 Bytes of V)
Meter Value 1 = 0x09(V)
Meter Value 2 = 0x01(V)
AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.5 (V)
2-2-5 AC load current ( I )
When receiving Meter Get Command, it will report Meter Report Command to the
node.
Meter Get Command: [Command Class Meter, Meter Get, Scale =0x05( )]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01，
Precision = 2，Scale = 0x05，Size = 2，Meter Value( )]
Example:
Scale = 0x05 (I)
Precision = 2
Size = 2 (2 Bytes of I)
Meter Value 1 = 0x01(I)
Meter Value 2 = 0x21(I)
AC load current = (Meter Value 1*256) +(Meter Value 2)= 2.89 (A)
2-2-6 load power factor (PF)
When receiving Meter Get Command, it will report Meter Report Command to the
node.
Meter Get Command: [Command Class Meter, Meter Get, Scale =0x06(PF)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01 ，Precision = 2，Scale = 0x06，Size = 1 Bytes，Meter Value(PF)]
7

Example:
Scale = 0x06 (PF)
Precision = 2
Size = 1 (1 Byte of PF)
Meter Value 1 = 0x63(PF)
Load power factor (PF) = Meter Value 1 =0.99
3. Z-Wave’s Configuration
Configuration
Parameter
Function Size
(Byte)
Value Unit Default Description
1 Watt Meter
Report Period
2 0x01-
0x7FFF
5s 720 720*5s=3600s=1 hour
2 KWH Meter
Report Period
2 0x01-
0x7FFF
10min 6 6*10min=1 hour
3 Threshold of
current for Load
caution
2 10-1100 0.01A 1100 1100*0.01A = 11A
4 Threshold of
KWh for Load
caution
2 1-10000 1KWh 10000
5 Restore switch
state mode
1 0-2 1 0 : Switch off
1 : Last switch state
2 : Switch on
6 Manual On/Off
mode
1 0-1 1 0：Disable
manual On/Off
1：Enable
manual On/Off
7 LED indication 1 1-3 1 1 : Show switch state
mode 2 : Show night mode
3 : One flash mode
8 Auto off timer 2 0-0x7FFF 1s 0 0 : Disable auto off
function
1-0x7FFF : 1s ~
32767s
9 RF off com-
mand mode
1 0-3 0 0 : Switch off
1 : Ignore
2 : Switch toggle
3 : Switch on
10 Edge or Pulse
mode or
Edge-Toggle
mode
1 1-3 1 1：Edge mode
2：Pulse mode
3：Edge-Toggle mode
11 Manual Switch
Report mode
1 0-1 1 0 : Disable
1 : Enable
14 Watt differential
report mode
1 0-4 1 0 : Disable
1 : 5%
2 : 10%
3 : 15%
4 : 20%
3-1 Watt Meter Report Period:
If the setting is configured for 1hour (set value =720), the PAN03/PAN10 will report
its instant power consumption every 1 hour to Group1 node. The maximum
interval to report its instant power consumption is 45 hours
(5s*32767/3600=45hr).
3-2 KWH Meter Report Period:
If the setting is configured for 1hour (set value =6), the PAN03/PAN10 will report its
Accumulated Power Consumption (KW/h) every 1 hour to Group1 node. The
maximum interval to report its Accumulated Power Consumption (KW/h) is 227.55
days (10min*32767/1440=227.55 days).
8

3-3 Threshold of current for Load Caution
This is a warning when the current of load over the preset threshold value, if the
setting value is 1100, when the load current of Relay1 over this value,
PAN03/PAN10 will send current meter report to warn the Group1 node, the Range
of the setting value is from 10 to 1100, and the default value is 1100.
3-4 Threshold of KWh for Load Caution
This is a warning when the KWh of load over the preset threshold value, if the
setting value is 10000, when the Accumulated Power Consumption of Relay1
over this value, PAN03/PAN10 will send KWH meter report to warn the Group1
node, minimum value is 1KWh and default value is 10000 kWh.
3-5 Restore switch state mode:
Whenever the AC power return from lost, PAN03/PAN10 will restore the switch
state which could be SWITCH OFF、LAST SWITCH STATE、SWITCH ON. The
default setting is LAST SWITCH STATE.
3-6 Manual On/Off Mode:
The On/Off function of S1、S2 and learn switch can be disabled or enabled by this
parameter, default value is Enable. But the learning operation won’t be affected.
When manual On/Off function is disabled, the RF command can only switch On
but not Off. This is useful function for keeping the device in switch on state.
3-7 LED indication mode:
3-7-1 Show Switch State：When switch is on, LED is on. When switch is off, LED
is off. The default setting is Show Switch State.
3-7-2 Show Night mode：When switch is on, LED is off. When switch is off, LED
is on.
3-7-3 One Flash mode：When the state of switch changes, LED will be on only
one second, then LED keeps off.
3-8 Auto off timer：
Whenever PAN03/PAN10 switches to on, the auto off timer begin to count down.
After the timer decrease to zero, it will switch to off automatically. However if Auto
off timer is set as 0, the auto off function will be disabled. The default setting is 0.
3-9 RF off command mode
Whenever a switch off command, BASIC_SET、BINARY_SWITCH_SET、
SWITCH_ALL_OFF, is received, it could be interpreted as 4 variety of commands.
3-9-1 Switch Off：It switches to OFF state. The default setting is Switch Off.
3-9-2 Ignore：The switch off command will be ignored.
3-9-3 Switch Toggle：It switches to the inverse of current state.
3-9-4 Switch On：It switches to ON state.
3-10 Edge mode、Pulse mode and Edge-Toggle mode
Manual switch S1 and S2 can set to Edge mode or Pulse mode or Edge-Toggle
mode, default value is Edge mode. But this parameter is useless to PAN10.
3-10-1 Edge mode: this mode is suitable for the bi-stable wall switch that has indica-
tor point on the switch, and the same position correspond to same state of re-
lay1. If the PAN03/PAN10 relay change the state because of receiving -
Wave RF command, it may need two times of change (switch on to off or
switch off to on) to let relay back to the correspond state. Manual switch S2 is
disabled in this mode.
3-10-2 Pulse mode: this mode is suitable for the toggle type wall switch to swap the
state of Relay1.
3-10-3 Edge-Toggle mode: this mode is suitable for the normal bi-stable switch,
whenever change the state of the wall switch will also swap the state of Re-
lay1.
3-11 Manual Switch Report mode :
9

Whenever PAN03 is manually switch on or off, it will send BINARY_SWITCH_
REPORT to the node of group1. The default setting is Enable the function.
3-12 Watt differential report mode :
3-12-1 Disable : The function of Watt differential report will be disabled.
3-12-2 5% : When the differential value of Watt is over 5%, PAN03/PAN10 will send
a meter report to the associated group.
3-12-3 10% : When the differential value of Watt is over 10%, PAN03/PAN10 will
send a meter report to the associated group.
3-12-4 15% : When the differential value of Watt is over 15%, PAN03/PAN10 will
send a meter report to the associated group.
3-12-5 20% : When the differential value of Watt is over 20%, PAN03/PAN10 will
send a meter report to the associated group.
4. Protection Command Classes
PAN03/PAN10 supports Protection Command Class version 2, it can protect the
switch against unintentionally control by e.g. a child. And it can also protect the
switch from being turned off by setting it in “No RF Control” state.
After being set to “Protection by sequence” state, any intentional pressing of On/Off
button should be hold longer than 1 second, or the switch state will not change.
However, the operation of learn function does not change, because learning will not
be protected.
5. Firmware update over the air (OTA)
PAN03 is based on 500 series SoC and supports Firmware Update Command Class,
it can receives the updated firmware image sent by controller via the -wave RF me-
dia. It is a helpful and convenient way to improve some function if needed.
6. Command Classes
The Switch supports Command Classes including…
* COMMAND_CLASS_ WAVEPLUS_INFO
* COMMAND_CLASS_VERSION
* COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
* COMMAND_CLASS_SECURITY
* COMMAND_CLASS_DEVICE_RESET_LOCALLY
* COMMAND_CLASS_ASSOCIATION_V2
* COMMAND_CLASS_ASSOCIATION_GRP_INFO
* COMMAND_CLASS_POWERLEVEL
* COMMAND_CLASS_SWITCH_BINARY
* COMMAND_CLASS_BASIC
* COMMAND_CLASS_SWITCH_ALL
* COMMAND_CLASS_METER_V3
* COMMAND_CLASS_CONFIGURATION
* COMMAND_CLASS_ALARM
* COMMAND_CLASS_PROTECTION
* COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
Troubleshooting
Symptom Cause of Failure Recommendation
The Switch not working and
LED off
1. The Switch is not
plugged into the
1. Check power connections
2. Don’t open up the Switch and
10