Philips AVENT SCD600 User manual

SCD600

2

3
1
16
22
21
20
15
14
17
13
12
11
10
918 19
2
3
4
5
7
8
1
2
3
4
6
10
11
8
712
14
13
5
6
9
1

4


 6
 16
 26
 37
 49
 60
 70
 81
 92
 102
 112
 123
 133
150
158

6

Congratulations on your purchase and welcome to Philips AVENT! To fully benet from the support
that Philips AVENT offers, register your product at www.philips.com/welcome.
The Philips AVENT video monitor provides you with round-the-clock support and it allows you to
see your baby day and night from anywhere in the house. The latest digital technology guarantees
crystal-clear sound and the clearest image of your baby. This gives you an additional sense of security
without entering your baby’s room and disturbing its sleep.

 
 Antenna
 Signal strength symbol
 Video display
 Lullaby symbol
 Battery/power-on light
 LINK light
 Sound level lights
 Loudspeaker
 Socket for appliance plug
 Adapter
 Rechargeable battery
 Automatic screen activation light
 Lullaby light
 Volume wheel with power-off position
 Brightness adjustment buttons
 Battery symbol
 Small plug
 Belt clip/stand
 Battery compartment lid
 Automatic screen activation button
 ’Next lullaby’ button
 Lullaby play/stop button
 
 Antenna
 Power-on light
 Lens
 Stand
 Adapter
 Battery compartment lid
 Microphone
 Nightlight button
 Nightlights
 Loudspeaker
 On/off switch
 Socket for appliance plug
 Non-rechargeable batteries (not included)
 Small plug

Read this user manual carefully before you use the appliance and save it for future reference.



- Never immerse any part of the baby monitor in water or any other liquid.

- Check if the voltage indicated on the adapters of the baby unit and the parent unit corresponds
to the local mains voltage before you connect the appliance.
- Only use the adapters supplied to connect the baby unit and the parent unit to the mains.
- The adapters contain a transformer. Do not cut off the adapters to replace them with other
plugs, as this causes a hazardous situation.
- If the adapters are damaged, always have them replaced with one of the original type in order
to avoid a hazard. For the correct type, see chapter ‘Replacement’.
- Never use the baby monitor in moist places or close to water.
- Except for the battery compartments, do not open the housing of the baby unit and parent unit
in order to prevent electric shock.
- This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety.
- Children should be supervised to ensure that they do not play with the appliance.

- Use and store the appliance at a temperature between 10°C and 35°C.
- Do not expose the baby unit and parent unit to extreme cold or heat or to direct sunlight. Do
not put the baby unit and the parent unit close to a heating source.
- Make sure the baby unit and the cord are always out of reach of the baby (at least 1 metre/3
feet away).
- Never place the baby unit inside or mount it on the baby’s bed or playpen.
- Never cover the parent unit and the baby unit with anything (e.g. a towel or blanket).

- This baby monitor is intended as an aid. It is not a substitute for responsible and proper adult
supervision and should not be used as such.
- The operating range of the baby monitor is 150 metres/490 feet in open air. Depending on the
surroundings and other disturbing factors, this range may be smaller.
- If you have any combination of cordless phones, wireless video, Wi-Fi networks, microwave or
Bluetooth on 2.4Ghz, connection problems may occur. The connection between the parent unit
and the baby unit could be lost for some seconds or may cause interference with other devices.
- We advise you to use the parent unit connected to the mains to save energy. The baby video
monitor consumes more energy than a standard baby monitor (without video).

- Always place a rechargeable battery of the correct type in the parent unit. Do not use non-
rechargeable batteries to avoid the risk of explosion.
- Always place non-recheargeable batteries of the correct type in the baby unit. The baby unit
does not have a charging function.
- Make sure that your hands are dry when you insert or replace the batteries.
- To avoiding damage due to battery leakage:
 Do not expose the appliance to temperatures higher than 35°C.
 Remove the rechargeable battery and the non-rechargeable batteries if you are not going
to use the appliance for one month or more.
 Do not leave empty batteries in the baby unit.
 7


This Philips AVENT appliance complies with all standards regarding electromagnetic elds (EMF). If
handled properly and according to the instructions in this user manual, the appliance is safe to use
based on scientic evidence available today.


You can use the baby unit from the mains or on non-rechargeable batteries. Even if you are going to
use the unit from the mains, we advise you to insert non-rechargeable batteries. This guarantees
automatic back-up in case of mains failure.

1 Put the appliance plug in the baby unit and put the adapter in a wall socket (Fig. 2).

The baby unit runs on four 1.5V R6 AAA batteries (not included). We strongly advise you to use
Philips R06 PowerLife batteries.
Do not use rechargeable batteries, as the baby unit does not have a charging function.
Unplug the baby unit and make sure your hands and the unit are dry when you insert non-
rechargeable batteries.
1 Remove the screw in the battery compartment lid with a athead screwdriver (Fig. 3).
2 Remove the battery compartment lid. (Fig. 4)
3 Insert four non-rechargeable batteries (Fig. 5).
Note: Make sure the + and - poles point in the right direction.
4 Reattach the lid.
5 Fasten the screw with a athead screwdriver.


Unplug the parent unit and make sure your hands and the unit are dry when you insert the
rechargeable battery.
The parent unit comes with a rechargeable Li-ion 1050mAh battery.
Charge the parent unit before you use it for the rst time or when the parent unit indicates that the
battery is low (when the empty battery symbol ashes on the video display and the battery light on
the parent unit ashes green).
Note: If the battery is completely empty, the parent unit automatically switches off and loses contact with
the baby unit.
1 Slide down the battery compartment lid to remove it (Fig. 6).
2 Insert the rechargeable battery (Fig. 7).
Note: Make sure the + and - poles point in the right direction.
3 Reattach the lid (Fig. 8).
4 Insert the appliance plug into parent unit and put the adapter in a wall socket (Fig. 9).
,The battery light on the parent unit lights up blue and the video display shows a battery
symbol (Fig. 10).
,When the battery is fully charged, the battery light turns green.
8

- When you charge the parent unit for the rst time or after a long period of disuse, switch it
off and let it charge continuously for at least 4 hours.
- Charging normally takes 3.5 hours, but it takes longer when the parent unit is switched on
during charging. To keep the charging time as short as possible, switch off the parent unit during
charging.
- When the batteries are fully charged, the parent unit can be used cordlessly for at least 8 hours
if it is in automatic screen activation mode. If the video is on continuously, the parent unit can be
used cordlessly for approx. 6 hours.
Note: When the parent unit has been charged for the rst time, the operating time is less than 6 hours.
The rechargeable battery only reaches its full capacity after you have charged and discharged it four
times.
Note: The battery gradually discharges, even when the parent unit is switched off.

1 Place the parent unit and the baby unit in the same room to test the connection (Fig. 11).
Make sure the baby unit is at least 1 metre/3 feet away from the parent unit.
2 Set the ON/OFF switch on the baby unit to the ON position. (Fig. 12)
,The green power-on light goes on. (Fig. 13)
Note: The power-on light always lights up green, even when there is no connection with the parent unit.
3 To switch on the parent unit, turn the volume wheel in the ‘ON’ direction to the desired
volume level. (Fig. 14)
,The power-on/battery light goes on. If the parent unit is charging, the power-on/battery light
is blue. When the parent unit is fully charged, the power-on/battery light turns green.
Note: The power-on/battery light always goes on, even when there is no connection with the baby unit.
,The video display goes on and the battery symbol appears on it (Fig. 15).
,The LINK light ashes red to indicate that the parent unit is searching for a connection with
a baby unit. (Fig. 16)
,The LINK light on the parent unit turns green and lights up continuously when a connection
has been established between the baby unit and parent unit. The baby is shown on the video
display. (Fig. 17)
Note: If no connection can be established, the LINK light on the parent unit ashes red, the parent
unit beeps and ‘OUT OF RANGE’ appears on the display. (Fig. 18)

Keep the baby unit out of the reach of the baby. Never place the baby unit inside or mount it on
the baby’s bed or playpen.
Note: If you use a Wi-Fi network, microwave oven or a DECT-system and you experience interference on
either the parent unit or baby unit, move the parent unit further away until there is no more interference.
1 Place the baby unit at least 1 metre/3 feet away from your baby, but no further than 1.5
metres/5 feet away (Fig. 19).
2 Place the stand of the baby unit on a stable, level and horizontal surface.
Tip: Position the baby unit at a higher level to get a good overview of the baby’s bed or playpen.
3 Place the baby unit on the stand and adjust its position in a way that ensures the best
visibility of your baby (Fig. 20).
 9

Do not position the baby unit with the microphone facing downwards. When the microphone
is blocked by the base, the baby unit does not pick up sounds properly.
4 Place the parent unit within the operating range of the baby unit. Make sure it is at least 1
metre/3 feet away from the baby unit to avoid acoustic feedback (Fig. 21).
For more information on the operating range, see section ‘Operating range’ below.

The operating range of the baby monitor is 150 metres/490 feet in open air. Depending on the
surroundings and other disturbing factors, this range may be smaller.
Dry materials Material thickness Loss of range
Wood, plaster, cardboard, glass
(without metal, wires or lead) < 30cm/12in 0-10%
Brick, plywood < 30cm/12in 5-35%
Reinforced concrete < 30cm/12in 30-100%
Metal grilles or bars < 1cm /0.4in 90-100%
Metal or aluminium sheets < 1cm/0.4in 100%
For wet and moist materials, the range loss may be up to 100%.


You can adjust the loudspeaker volume of the parent unit to the level you prefer.
1 Turn the volume wheel to adjust the volume. (Fig. 14)
Note: If the volume is set to a high level, the parent unit consumes more power.

You can adjust the display brightness of the parent unit to the level you prefer.
1 Press the brightness adjustment buttons on the parent unit to adjust the brightness of the
video display. (Fig. 22)
Note: If the brightness is set to a high level, the parent unit consumes more power.

The parent unit continuously monitors the sound level in your baby’s room and the sound level
lights let you know if there is any activity. If your baby cries, the green sound level lights light up on
the parent unit.
- As long as the baby unit does not detect a sound, all sound level lights on the parent unit are
out.
- When the baby unit picks up a sound, one or more sound level lights on the parent unit go on.
The number of lights that go on is related to the loudness of the sound picked up by the baby
unit. The sound level lights also go on when the parent unit is set to a low volume or when the
automatic screen activation mode is activated (see section ‘Automatic screen activation’
below) (Fig. 23).
10


The parent unit continuously monitors the sound level in your baby´s room. When the automatic
screen activation mode is activated, the video display only switches on when the baby unit picks up
a sound. As long as no sound is detected, the video display is off to save power.
1 To activate the automatic screen activation mode, press the automatic screen activation
button on the parent unit. (Fig. 24)
,The automatic screen activation light on the parent unit goes on (Fig. 25).
,When the baby unit detects a sound, the video display on the parent unit automatically goes
on to show the baby. When no sound is detected for 30 seconds, the video display goes out
again.
2 To switch off the automatic screen activation mode, press the automatic screen activation
button on the parent unit again.

1 Press the nightlight button on the baby unit to switch on the nightlights. (Fig. 26)
,The nightlights on the baby unit go on. (Fig. 27)
2 Press the nightlight button again to switch off the nightlights.
Tip: Switch off the nightlights when you operate the baby unit on non-rechargeable batteries. This saves
power.

Note: When the baby unit plays a lullaby, it consumes more power.
1 Press the play/stop button to start the lullaby (Fig. 28).
,The lullaby starts to play on the baby unit and repeats continuously.
2 To stop the lullaby, press the play/stop button on the parent unit again.
3 To select another lullaby when a lullaby is playing:
- Press the ‘next lullaby’ button on the parent unit. (Fig. 29)
- If you want a different lullaby, press the ‘next lullaby’ button on the parent unit again.

When the parent unit is out of range of the baby unit, the parent unit beeps once and the
message ‘Out of range’ appears on the video display. The LINK light on the parent unit ashes red.
Note: The message ‘Out of range’ also appears on the video display of the parent unit when the baby unit
is switched off.

The camara has infrared lights that allow you to see your baby clearly, even in a dark room. When
the lens detects low light levels, the infrared lights are activated automatically. Place the baby unit 1
to 1.5 metres/3 to 5 feet away from the baby to ensure a clear view.

If the rechargeable battery of the parent unit is sufciently charged, you can take the unit with you
inside and outside the house by attaching the unit to your belt or waistband with the belt clip. This
allows you to monitor your baby while you are moving around.
 11


Do not immerse the parent unit and the baby unit in water and do not clean them under the tap.
Do not use cleaning spray or liquid cleaners.
1 Switch off the baby unit and the parent unit and unplug them if they are connected to the
mains.
2 Clean the parent unit and the baby unit with a damp cloth.
Note: Fingerprints or dirt on the lens of the baby unit may affect the camera’s performance. Avoid
touching the lens with your ngers.
Make sure the baby unit and parent unit are dry before you connect them to the mains again.
3 Clean the adapters with a dry cloth.

When you are not going to use the baby monitor for some time, remove the non-rechargeable
batteries from the baby unit and the rechargeable battery from the parent unit. Store the parent
unit, the baby unit and the adapters in a cool and dry place.

The following items are replaceable:
- Magnetic stand for baby unit
- Adapters. (type number OH-1048A0600800U-VDE (Europe, VDE) or OH-1048A0600800U-
UK (UK).
- Li-ion rechargeable battery
- Battery compartment lid
Note: Only replace the stand, adapters, rechargeable battery and battery compartment lid with ones of
the original type.

You can order a new adapter from your Philips dealer or a Philips service centre under type number
OH-1048A0600800U-VDE (Europe, VDE) or OH-1048A0600800U-UK (UK).

- Do not throw away the appliance with the normal household waste at the end of its life, but
hand it in at an ofcial collection point for recycling. By doing this, you help to preserve the
environment (Fig. 30).
- Rechargeable and non-rechargeable batteries contain substances that may pollute the
environment. Do not throw away rechargeable and non-rechargeable batteries with the normal
household waste, but hand them in at an ofcial collection point. Always remove rechargeable
and non-rechargeable batteries before you discard and hand in the appliance at an ofcial
collection point. (Fig. 31)

If you need service or information or if you have a problem, please visit the Philips AVENT website
at www.philips.com/AVENT or contact the Philips Consumer Care Centre in your country (you
nd its phone number in the worldwide guarantee leaet). If there is no Consumer Care Centre in
your country, go to your local Philips dealer.
12


This chapter lists the questions most frequently asked about the appliance. If you cannot nd the
answer to your question, contact the Consumer Care Centre in your country.
Question Answer
Why don’t the power-on
light of the baby unit and
the parent unit go on
when I switch on the
units?
Perhaps the rechargeable battery of the parent unit is empty and the
parent unit is not connected to the mains. Insert the appliance plug
into the parent unit and put the adapter in a wall socket. Then move
the volume wheel in the ‘ON’ direction to switch on the parent unit
and to establish connection with the baby unit.
Perhaps the baby unit is not connected to the mains and the non-
rechargeable batteries in the baby unit are empty or there are no
non-rechargeable batteries in the baby unit at all. Put full non-
rechargeable batteries in the baby unit or connect the baby unit to
the mains. Then set the on/off switch to ‘ON’ to switch on the baby
unit and to establish connection with the parent unit.
Why does the LINK light
on the parent unit ash
red?
The baby unit and the parent unit are out of range of each other.
Move the parent unit closer to the baby unit.
The baby unit may be switched off. Switch on the baby unit.
Why does the battery/
power-on light on the
parent unit ash green?
The rechargeable battery of the parent unit is running low. Recharge
the battery (see chapter ‘Preparing for use’).
Why does the parent
unit beep? If the parent unit beeps while the LINK light lights up red continuously, the connection with the baby unit is lost. Move the parent unit closer
to the baby unit.
The baby unit may be switched off. Switch on the baby unit.
Why does the video
monitor produce a high-
pitched noise?
The units may be too close to each other. Make sure the parent unit
and the baby unit are at least 1 metre/3 feet away from each other.
The volume of the parent unit may be set too high. Decrease the
volume of the parent unit.
Why don’t I hear a
sound/Why can’t I hear
my baby cry?
The volume of the parent unit may be set too low or may be
switched off. Turn the volume wheel to a higher volume level.
Perhaps you have switched on the automatic screen activation. If the
automatic screen activation is activated, the video display only
switches on when the baby unit picks up a sound. As long as no
sound is detected, the video display is off to save power.
Why does the parent
unit react too quickly to
other sounds?
The baby unit also picks up other sounds than those of your
baby. Move the baby unit closer to the baby (but observe the
minimum distance of 1 metre/3 feet).
 13

Question Answer
Why do the non-
rechargeable batteries of
the baby unit run low
quickly?
Perhaps you have switched on the nightlights. If you want to use the
nightlights, we advise you to use the baby unit on mains power.
Perhaps you are playing lullabies. The baby unit consumes a lot of
energy when you play lullabies. If you play lullabies, we advise you to
use the baby unit on mains power.
Why does the charging
time of the parent unit
exceed 3.5 hours?
The parent unit may be switched on during charging. Switch off the
parent unit during charging.
The specied operating
range of the baby
monitor is 150
metres/490 feet. Why
does my baby monitor
manage a much smaller
distance than that?
The specied range is only valid outdoors in open air. Inside your
house, the operating range is limited by the number and type of walls
and/or ceilings in between.
Why can’t I establish a
connection? Why is the
connection lost every
now and then? Why are
there sound
interruptions?
The baby unit and the parent unit are probably close to the outer
limits of the operating range or there is interference from other
2.4GHz wireless devices. Try a different location, decrease the distance
between the units or switch off other 2.4GHz wireless devices. Please
note that it takes about 5 seconds each time before a connection
between the units is established.
What happens during a
power failure? If the parent unit is sufciently charged, it continues to operate during a power failure. If there are batteries in the baby unit, it also continues
to operate during a power failure.
The operating time of
the parent unit is
supposed to be at least 6
hours. Why is
the operating time of my
parent unit shorter?
When the parent unit has been charged for the rst time, the
operating time is shorter because the battery has not reached its full
capacity yet. The rechargeable battery only reaches its full capacity
after you have charged and discharged it at least four times. After
this, the operating time is 6 hours if the automatic screen activation is
not activated and 8 hours if the automatic screen activation mode is
activated.
The parent unit consumes a lot of energy when the video display is
switched on continuously. Activate the automatic screen activation
mode to increase the operating time (see chapter ‘Features’, section
‘Automatic screen activation’).
The volume of the parent unit may be set too high, which causes the
parent unit to consume a lot of energy. Decrease the volume of the
parent unit
Why do I get
interference on the
parent unit?
Interference may occur when the parent unit is out of range of the
baby unit. Interference may also occur if there are too many walls or
ceilings between the parent unit and the baby unit or when other
2.4GHz wireless devices are switched on (e.g. microwave, internet).
Put the parent unit in a different place, closer to the baby unit, or
switch off other wireless devices.
14

Question Answer
Why does the parent
unit make a buzzing
sound?
Interference may occur when the parent unit is out of range of the
baby unit. Interference may also occur if there are too many walls or
ceilings between the parent unit and the baby unit or when other
2.4GHz wireless devices are switched on (e.g. microwave, internet).
Put the parent unit in a different place, closer to the baby unit, or
switch off other wireless devices.
The rechargeable battery of the parent unit may need to be charged.
Why does the video
display icker? Interference may occur when the parent unit is out of range of the baby unit. Interference may also occur if there are too many walls or
ceilings between the parent unit and the baby unit or when other
2.4GHz wireless devices are switched on (e.g. microwave, internet).
Put the parent unit in a different place, closer to the baby unit, or
switch off other wireless devices.
The rechargeable battery of the parent unit may need to be charged.
Why isn’t there any
image on the video
display when the power-
on light is on?
The parent unit may be in the automatic screen activation mode.
Press the automatic screen activation button again to switch on the
video display.
Why isn’t the image on
the video display clear? The display brightness may be set too low. Increase the display brightness (see chapter ‘Features’).
Why doesn’t the parent
unit work in the
automatic screen
activation mode?
The distance between the baby and the baby unit may be too large.
Make sure that the baby unit is placed 1 to 1.5 metres/3 to 5
feet away from the baby.
Why isn’t the image on
the video display clear
in night vision?
The distance between the baby and the baby unit may be too large.
Make sure that the baby unit is placed 1 to 1.5 metres/3 to 5
feet away from the baby.
Why doesn’t the battery
symbol appear on the
video display of the
parent unit when I start
to charge the parent
unit?
It may take a few minutes before the battery symbol appears on the
video display of the parent unit when you charge the parent for the
rst time or after a long period of disuse.
Why doesn’t the parent
unit charge when I have
plugged it in?
The rechargeable battery may have reached the end of its life.
Replace the rechargeable battery.
 15

16

Tillykke med dit køb og velkommen til Philips AVENT! For at få fuldt udbytte af den support, Philips
AVENT tilbyder, skal du registrere dit produkt på www.philips.com/welcome.
Med Philips AVENT-videomonitoren får du adgang til support døgnet rundt og mulighed for at
holde øje med din baby dag og nat fra overalt i huset. Den nyeste digitale teknologi garanterer
krystalklar lyd og det klareste billede af din baby. Dette giver dig en forstærket fornemmelse af
tryghed, uden at du behøver gå ind på værelset og forstyrre babyens søvn.

 
 Antenne
 Signalstyrkesymbol
 Videoskærm
 Vuggevisesymbol
 Batteri-/strømindikator
 LINK-lysindikator
 Lys, som indikerer lydniveau
 Højttaler
 Tilslutningsstik
 Adapter
 Opladeligt batteri
 Indikator for automatisk skærmaktivering
 Vuggeviseindikator
 Lydstyrkehjul med slukposition
 Knapper til lysstyrkeregulering
 Batterisymbol
 Lille stik
 Bælteclips/stander
 Låg til batterirum
 Knap til automatisk skærmaktivering
 Knap til “next lullaby” (næste vuggevise)
 Afspil/stop-knap til vuggevise
 
 Antenne
 Strømindikator
 Objektiv
 Stander
 Adapter
 Låg til batterirum
 Mikrofon
 Natlystast
 Natlys
 Højttaler
 On/off-kontakt (tænd/sluk)
 Tilslutningsstik
 Ikke-genopladelige batterier (medfølger ikke)
 Lille stik

Læs denne brugsvejledning omhyggeligt igennem, inden apparatet tages i brug, og gem den til
eventuelt senere brug.



- Babyalarmen (eller dele af den) må aldrig kommes ned i vand eller andre væsker.

- Kontrollér, om den angivne netspænding på adapteren til babyenheden og forældreenheden
svarer til den lokale netspænding, før du tilslutter apparatet.
- Brug kun de medfølgende adaptere ved tilslutning af babyenheden og forældreenheden til
lysnettet.
- Begge adaptere indeholder en transformer, som aldrig må klippes af eller udskiftes med andre
stik, da dette kan være meget risikabelt.
- Hvis adapterne er beskadigede, skal de altid udskiftes med en original type for at undgå fare. Se i
kapitlet “Udskiftning” for at nde den korrekte type.
- Babyalarmen må ikke bruges i fugtige omgivelser eller tæt ved vand.
- Forsøg aldrig at åbne andet end baby- eller forældreenhedens batterirum for at undgå elektrisk
stød.
- Dette apparat er ikke beregnet til at blive brugt af personer (herunder børn) med nedsatte
fysiske og mentale evner, nedsat følesans eller manglende erfaring og viden, medmindre de er
blevet vejledt eller instrueret i apparatets anvendelse af en person, der er ansvarlig for deres
sikkerhed.
- Apparatet bør holdes uden for børns rækkevidde for at sikre, at de ikke kan komme til at lege
med det.

- Apparatet skal opbevares ved temperaturer mellem 10°C og 35°C.
- Hverken baby- eller forældreenheden må udsættes for ekstrem kulde eller varme eller for
direkte sollys. Anbring aldrig baby- eller forældreenheden i nærheden af en varmekilde.
- Babyenheden og dens ledning skal altid være uden for barnets rækkevidde (mindst 1 meter
væk).
- Anbring eller monter ikke babyenheden i eller på barnets seng eller kravlegård.
- Forældre- og babyenhederne må aldrig tildækkes (f.eks. med et håndklæde eller et tæppe).

- Denne babyalarm er beregnet som et hjælpemiddel. Den kan aldrig erstatte ansvarlig og korrekt
forældreopsyn og -overvågning og må ikke bruges sådan.
- Babyalarmen har en senderækkevidde på 150 m i fri luft. Rækkevidden kan være kortere
afhængigt af omgivelserne og andre forstyrrende faktorer.
- Hvis du har en kombination af trådløse telefoner, trådløs video, Wi-Fi-netværk, mikrobølger eller
Bluetooth på 2,4 Ghz, kan der opstå problemer med forbindelsen. Forbindelsen mellem
forældre- og babyenhed kan gå tabt i et par sekunder eller kan medføre interferens for andre
enheder.
- Vi anbefaler, at forældreenheden er sluttet til stikkontakten for at spare på strømmen.
Babyvideomonitoren forbruger mere energi end en standardmonitor (uden video).

- Brug altid et genopladeligt batteri af den korrekte type i forældreenheden. Undgå at bruge ikke-
genopladelige batterier for at undgå eksplosionsfare.
- Brug altid ikke-genopladelige batterier af den korrekte type i babyenheden. Babyenheden er ikke
udstyret med en opladningsfunktion.
- Sørg for, at dine hænder er helt tørre, når batterierne isættes eller udskiftes.
- Sådan undgås eventuel beskadigelse pga. batterilækage:
 Apparatet bør ikke udsættes for temperaturer over 35°C.
 Fjern det genopladelige batteri og de ikke-genopladelige batterier, hvis du ikke skal bruge
apparater i en måned eller mere.
 Lad ikke opbrugte batterier blive siddende i babyenheden.
 17


Dette Philips AVENT-apparat overholder alle standarder for elektromagnetiske felter (EMF). Ved
korrekt anvendelse i overensstemmelse med instruktionerne i denne brugsvejleding er apparatet
sikkert at anvende, ifølge den videnskabelige viden, der er tilgængelig i dag.


Babyenheden kan enten bruges via lysnettet eller med ikke-genopladelige batterier. Selvom enheden
får strøm fra lysnettet, anbefaler vi, at du isætter ikke-genopladelige batterier. Så er du sikker på, at
enheden virker også i tilfælde af strømsvigt.

1 Sæt stikket til apparatet i babyenheden og sæt adapteren i en stikkontakt (g. 2).

Babyenheden benytter re 1,5 V batterier af typen R6 AAA (medfølger ikke). Vi anbefaler Philips R06
PowerLife-batterier.
Anvend ikke genopladelige batterier, da babyenheden ikke har nogen ladefunktion.
Tag babyenheden ud af stikkontakten, og sørg for, at dine hænder og enheden er tørre, når du
isætter ikke-genopladelige batterier.
1 Fjern skruen i låget til batterirummet med en almindelig skruetrækker (g. 3).
2 Fjern låget til batterirummet. (g. 4)
3 Isæt re ikke-genopladelige batterier (g. 5).
Bemærk: Sørg for, at polerne (- og +) vender rigtigt.
4 Sæt låget på igen.
5 Spænd skruen med en almindelig skruetrækker.


Tag forældreenheden ud af stikkontakten, og sørg for, at dine hænder og enheden er tørre, når du
isætter det genopladelige batteri.
Til forældreenheden medfølger et genopladeligt Li-ion 1050 mAh-batteri.
Genoplad forældreenheden, før du bruger den første gang, eller når forældreenheden indikerer, at
batteriet næsten er brugt op (når symbolet for tomt batteri blinker på videoskærmen, og
batteriindikatoren på forældreenheden blinker grønt).
Bemærk: Hvis batteriet er helt aadet, slukker forældreenheden automatisk, og kontakten til
babyenheden afbrydes.
1 Skub batterirummets dæksel nedad for at tage det af (g. 6).
2 Isæt det genopladelige batteri (g. 7).
Bemærk: Sørg for, at polerne (- og +) vender rigtigt.
3 Sæt låget på igen (g. 8).
4 Isæt apparatstikket i forældreenheden, og sæt adapteren i stikkontakten (g. 9).
,Batteriindikatoren på forældreenheden lyser blåt, og videoskærmen viser et
batterisymbol (g. 10).
,Når batteriet er fuldt opladet, lyser batteriindikatoren grønt.
18

- Når du oplader forældreenheden for første gang eller efter lang tid uden brug, skal du slukke
den og oplade den uafbrudt i mindst 4 timer.
- En fuld opladning tager normalt 3,5 timer, men varer længere, hvis forældreenheden er tændt
under opladningen. Sluk derfor altid forældreenheden under opladning for at gøre
opladningstiden så kort som muligt.
- Når batterierne er fuldt opladede, kan forældreenheden anvendes trådløst i mindst 8 timer, hvis
den er i automatisk skærmaktiveringstilstand. Hvis videoskærmen er tændt hele tiden, kan
forældreenheden anvendes trådløst i ca. 6 timer.
Bemærk: Efter første opladning af forældreenheden er brugstiden mindre end 6 timer. Det genopladelige
batteri når først op på sin fulde kapacitet, når det er blevet opladt og aadt re gange.
Bemærk: Batteriet aades gradvist, selv når forældreenheden er slukket.

1 Anbring forældreenheden og babyenheden i det samme rum, for at afprøve
forbindelsen (g. 11).
Babyenheden skal stå mindst 1 meter fra forældreenheden.
2 Stil ON/OFF-kontakten på babyenheden på ON. (g. 12)
,Den grønne strømindikator lyser. (g. 13)
Bemærk: On-/Off-indikatoren lyser altid grønt, også selv om der ikke er forbindelse til forældreenheden.
3 Drej lydstyrkehjulet over mod “ON” til det ønskede lydstyrkeniveau for at tænde forældreen
heden. (g. 14)
,Batteri-/strømindikatoren lyser. Hvis forældreenheden er ved at lade op, lyser batteri-/
strømindikatoren blåt. Når forældreenheden er fuldt opladet, lyser batteri-/strømindikatoren
grønt.
Bemærk: Batteri-/strømindikatoren lyser altid, selv når der ikke er forbindelse til babyenheden.
,Displayet tænder, og batterisymbolet vises (g. 15).
,LINK-indikatoren blinker rødt for at indikere, at forældreenheden prøver at oprette
forbindelse til en babyenhed. (g. 16)
,LINK-indikatoren på forældreenheden bliver grøn og lyser konstant, når der er
etableret forbindelse mellem babyenheden og forældreenheden. Babyen vises på
videoskærmen. (g. 17)
Bemærk: Hvis der ikke kan etableres forbindelse, blinker LINK-indikatoren på forældreenheden
rødt, forældreenheden bipper, og “OUT OF RANGE” (Uden for rækkevidde) vises på skærmen. (g. 18)

Hold babyenheden uden for babyens rækkevidde. Anbring eller monter ikke babyenheden i eller
på barnets seng eller kravlegård.
Bemærk: Hvis du bruger et Wi-Fi-netværk, en mikrobølgeovn eller et DECT-system, og du oplever
interferens på enten forældre- eller babyenheden, skal du ytte forældreenheden længere væk, indtil der
ikke er mere interferens.
1 Anbring babyenheden mindst 1 meter væk fra babyen, men ikke længere væk end 1,5
meter (g. 19).
2 Anbring standeren til babyenheden på en stabil, plan og vandret overade.
Tip: Anbring babyenheden højt for at få et godt overblik over babyens seng eller kravlegård.
3 Anbring babyenheden i standeren, og juster placeringen, så du får det bedste udsyn til dit
barn (g. 20).
 19

Anbring ikke babyenheden med mikrofonen pegende nedad. Hvis mikrofonen bliver blokeret af
standerens fod, opfanger babyenheden ikke lyde ordentligt.
4 Placer forældreenheden inden for babyenhedens senderækkevidde. Den skal stå mindst 1
meter fra babyenheden for at undgå akustisk tilbagekobling (g. 21).
Læs mere om senderens rækkevidde i afsnittet “Senderækkevidde” herunder.

Babyalarmen har en senderækkevidde på 150 m i fri luft. Rækkevidden kan være kortere afhængigt af
omgivelserne og andre forstyrrende faktorer.
Tørre materialer Materialets tykkelse Tab af rækkevidde
Træ, gips, pap, glas (uden metal,
ledninger eller bly) < 30 cm 0-10 %
Mursten, krydsner < 30 cm 5-35 %
Armeret beton < 30 cm 30-100 %
Metalgitter eller -stænger < 1 cm 90-100 %
Metal- eller aluminiumsplader < 1 cm 100 %
Våde og fugtige materialer kan give op til 100 % tab i rækkevidden.


Du kan justere lydstyrken for forældreenhedens højttaler til det ønskede niveau.
1 Drej på lydstyrkehjulet for at justere lydstyrken. (g. 14)
Bemærk: Hvis lydstyrken er indstillet til at være høj, bruger forældreenheden mere strøm.

Du kan justere skærmens lysstyrke på forældreenheden til det ønskede niveau.
1 Tryk på knapperne til justering af lysstyrke på forældreenheden for at justere lysstyrken på
videoskærmen. (g. 22)
Bemærk: Hvis lysstyrken er indstillet til at være høj, bruger forældreenheden mere strøm.

Forældreenheden overvåger kontinuerligt lydniveauet i babyens værelse, og vha.
lydniveauindikatorerne kan du se, om der er aktivitet i værelset. Hvis babyen græder, lyser de grønne
lydniveauindikatorer på forældreenheden.
- Så længe babyenheden ikke registrerer nogle lyde, er alle lydstyrke-indikatorerne på
forældreenheden slukkede.
- Når babyenheden opfanger en lyd, lyser en eller ere af indikatorerne for lydniveau på
forældreenheden. Antallet af indikatorer, der lyser, afhænger af lydstyrken af den lyd, som
babyenheden opfanger. Indikatorerne for lydniveau lyser også, når forældreenheden er indstillet
på lav lydstyrke, eller når automatisk skærmaktivering er aktiveret (se afsnittet “Automatisk
skærmaktivering” nedenfor) (g. 23).
20