Philips CEM2220BT User manual

Register your product and get support at
www.philips.com/support
Always there to help you
คู่มือผู้ใช้
User manual
使用手冊
CEM2220BT
Question?
Contact
Philips

1
English
EN
Contents
1 Safety 2
2 Your car audio system 3
Introduction 3
What's in the box 3
Overview of the main unit 4
3 Install the car audio system 6
Connect wires 6
Mount into the dashboard 7
Attach the front panel 8
4 Get started 9
For the rst time use 9
Set the time format 9
Set the clock 9
Turn on 9
Switch music listening zone 9
Mute the button beep 10
5 Listen to radio 11
Tune to a radio station 11
Store radio stations in memory 11
Tune to a preset station 11
Play with RDS 11
6 Play from hard media 14
Play a disc 14
Play from USB 14
Control play 14
Switch tracks 15
7 Use Bluetooth devices 16
Connect a device 16
Play audio from a Bluetooth device 17
Make a call 17
8 Connect external sound source 18
9 Adjust sound 19
10 Adjust system settings 20
11 Others 21
Reset 21
Replace fuse 21
12 Product information 22
Specications 22
USB playability information 22
13 Troubleshooting 23
General 23
About the Bluetooth device 23
14 Notice 25
Compliance 25
Care of the environment 25
Trademark notice 25
Copyright 25
15 Glossary 26

2EN
1 Safety
Read and understand all instructions before
you use your apparatus. If damage is caused by
failure to follow instructions, the warranty does
not apply.
• This apparatus is designed for negative
ground (earth) 12 V DC operation only.
• To ensure safe driving, adjust the volume to
a safe and comfortable level.
• Improper fuses can cause damage or
re. When you need to change the fuse,
consult a professional.
• Use only the supplied mounting hardware
for a safe and secure installation.
• To avoid short circuit, do not expose the
apparatus to rain or water.
• Never insert objects into the ventilation
slots or other openings on the apparatus.
• Clean the apparatus and frame with a soft,
damp cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the apparatus.
• Never place any objects other than discs
into the apparatus.
• Never use solvents such as benzene,
thinner, cleaners available commercially, or
anti-static sprays intended for discs.
• Visible and invisible laser radiation when
open. Avoid exposure to beam.
Caution
•Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
• The apparatus shall not be exposed to
dripping or splashing.
• Do not place any sources of danger on the
apparatus (e.g. liquid lled objects, lighted
candles).

3
English
EN
2 Your car audio
system
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With the in-car audio system, you can enjoy
your drive while listening to:
• FM or AM (MW) radio
• Audio from CD or MP3 disc
• Audio from USB devices
• Audio from Bluetooth devices
• Audio from other external devices
The unit supports the following media format:
What's in the box
Check and identify the contents of your
package:
a Main unit (with a sleeve)
b Front panel
c Trim plate
d Carrying case for front panel
e ISO male connectors
f Rubber cushion
g Screw x 1 pc
h Disassembly tools x 2 pcs
i User manual
a
e
ih
g
f
bc d

4EN
Overview of the main unit
a /
• Tune for radio station.
• Skip/search for track.
• Fast backward/forward playback.
b
• Press to answer or redial a call.
• Press and hold to transfer call.
c /MENU
• Return to previous menu.
• Access system menu.
s
a dcb e f g
np o h
r
q m l k ij
d /
• Turn the unit on or off.
• Conrm selection.
• Mute or unmute sound.
• Rotate to adjust volume.
e ZONE /
• Select tuner band.
• Select MP3/WMA folder.
• Press and hold to switch music
listening zone.

5
English
EN
f
• Eject disc.
g
• USB socket.
h AUDIO IN
• Connect external audio device.
i
6281'
/
• Turn on or off maximum sound
feature.
• In any mode, press and hold to view
clock.
j DBB/AS
• Press to turn on or off Dynamic Bass
Boost (DBB) sound.
• In radio mode, press and hold to
access to tuner auto store.
k /
• Start, pause, or resume the play of
tracks.
• In radio mode, press to select the
preset radio station of No. 5/6.
• In radio mode, press and hold to store
the current radio station at channel
No. 5/6.
l /
• In radio mode, press to select the
preset radio station of No. 3/4.
• In radio mode, press and hold to store
the current radio station at channel
No. 3/4.
• For .wma and .mp3 tracks, press
repeatedly to select shufe play/repeat
play.
m /
• In radio mode, press to select the
preset radio station of No. 1/2.
• In radio mode, press and hold to store
the current radio station at channel
No. 1/2.
• For .wma and .mp3 tracks on a storage
device, press to access the track/folder
list.
n SOURCE/DISPLAY
• Press repeatedly to select source.
• Display current status.
• Press and hold to select the dimmer
high or low.
o
• Press repeatedly to select a preset
equalizer (EQ).
• Press and hold to access audio setting
menu.
p
• Unlock the panel.
q
• Press to hang up a call.
• Press and hold to reject an incoming
call.
r RESET
• Restore default settings.
s Disc slot

6EN
3 Install the car
audio system
These instructions are for a typical installation.
However, if your car has different requirements,
make the adjustment accordingly. If you have
any question regarding installation kits, consult
your local retailer.
Note
•This system is designed for negative ground (earth) 12V
DC operation only.
•Always install this system in the car dashboard. Other
locations can be dangerous as the rear of the system
heats up during use.
•To avoid short-circuit: before you connect, make sure
that the ignition is off.
•Make sure that you connect the yellow and red power
supply leads after all other leads are connected.
•Make sure that all loose leads are insulated with
electrical tape.
•Make sure that the leads do not get caught under
screws or iron parts that will move (e.g. seat rail).
•Make sure that all ground (earth) leads are run to a
common ground (earth) point.
•Use only the supplied mounting hardware for a safe
and secure installation.
•Improper fuses can cause damage or re. When you
need to change the fuse, consult a professional.
•When you connect other devices to this system, make
sure that the rating of the car circuit is higher than the
total fuse value of all the connected devices.
•Never connect speaker wires to the metal body or
chassis of the car.
•Never connect speaker wires with stripes to one
another.
Connect wires
Note
•Consult a professional to connect CEM2220BT as
instructed below.
1 Check the car's wiring carefully and
connect them to the the supplied male
connector.
ISO male
connectors
Connect to
a Green strip, black-
edged green strip
Left speaker (Rear)
b White strip, black-
edged white strip
Left speaker (Front)
c Gray strip, black-
edged gray strip
Right speaker (Front)
d Purple strip, black-
edged purple strip
Right speaker (Rear)
e Red Ignition key +12V
DC when ON/ACC
f Blue Motor/electric
antenna relay control
lead
g White edged blue
strip
Amplier relay
control lead
h Black Ground
i Yellow To the +12V car
battery which is
energized at all times
2 Connect the antenna and amplier as
illustrated, if applicable.

7
English
EN
Connector Connect to
1 ANTENNA Antenna
2 Socket for ISO male
connectors
As indicated in
Step 1 above
3 REAR LINE OUT R
(Socket)
Rear right speaker
4 REAR LINE OUT L
(Socket)
Rear left speaker
5 OE REMOTE
(Purple)
OE Remote
Tip
•The pin arrangement for the ISO connectors depends
on the type of vehicle you drive. Be sure to make
proper connections to prevent damage to the unit.
Mount into the dashboard
1 If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
• If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer
may lose its memory.
• If the car battery is not disconnected,
to avoid short-circuit, ensure that the
bare wires do not touch each other.
2 Ensure that car dashboard opening is
within these measurements:
3 Remove the mounting sleeve with the
supplied disassembly tools.
4 Install the sleeve into the dashboard and
bend the tabs outward to x the sleeve.
Note
•If the unit is not xed by sleeve but by the supplied
screws, skip this step.
183 mm
53mm
5mm

8EN
5 Place the supplied rubber cushion over the
end of the mounting bolt.
6 Slide the unit into the dashboard until you
hear a click sound.
183 mm
53.5 mm
7 Reconnect the negative terminal of the car
battery.
Attach the front panel
1 Insert the notch on the front panel to the
chassis on the main unit.
2 Press the left end of the front panel
inwards until it is securely locked with a
"click".
Detach the front panel
Note
•Before you detach the front panel, make sure that the
system is turned off.
1 Press to release the front panel.
2 Pull the front panel outwards to remove it.