Philips CT6628/000000EU User manual

Discover Your Phone
Philips continuously strives to improve its products.
Therefore, Philips reserves the rights to revise this user
guide or withdraw it at any time without prior notice.
Philips provides this user guide "as is" and does not
accept, except as required by applicable law, liability
for any error, omission or discrepancy between this
user guide and the product described. The device is
meant to be connected to GSM/GPRS networks.
How to...
A
lphanumeric
keypad
Microphone
262k OLED
main screen
Pick up key
Hang up, cancel
and on/off key
Backofthephone:
camera lens
Charger /headset
connector
Left softkey
Right softkey
Navigation and
, keys
Volume keys
Voice memo key
Camera key
Switch the phone
On/Off
Long press ) .
Enter your PIN code Enter your PIN code using
the keypad and press , or L
to confirm.
Make a call Enter the phone number on
the keypad and press
( to
dial.
End a call Press ) .
Answer a call Press ( when your phone
rings.
Reject a call Press ) when your phone
rings.
Activate/deactivate
the loudspeaker
Long press ( during a call.
Activate the
Silent mode
Long press 6 .
Access QuickCall Press + in idle mode.
Access the Names list Press - in idle mode.

1
Softkeys
The left and right soft keys < and > located at the top
of the keypad allow you to select the corresponding
options that appear on the screen immediately above
them, including during calls. The functions associated
with these keys will vary according to the current
context.
Main Menu
The Main Menu gives you access to all the different
features of your mobile phone presented in the form
of a grid. The table above summarises the
arrangement of the
Main Menu , the meanings of the
various icons found there, and the page in this manual
where more detailed information concerning the
subject can be found.
Access the Call list Press ( in idle mode. The
Call list displays all calls
missed, dialled and received.
Access the Main Menu Press , or L Menu in idle
mode.
Go to previous menu Press R Back when available.
Quickly return
to idle Press
) .
Extras Media Album Entertainment
page 14 page 19 page 23
Op. Services Messages Settings
page 26 page 29 page 42
Camera Address Book Call Info
page 52 page 57 page 61

2
Press , to access the Main Menu when in idle mode,
then use the central navigation key which directions
are represented in the present guide with the
+ , - , < or
> signs to browse the icons and lists. When navigating
in a list, a scroll bar located on the right hand side of
the screen shows your current position in the list.
Within lists, press
, to access the options related to
the selected item, press select
R Back to go back one
level.
How to use this manual
The current manual is structured as follows:
Discover
your phone
The current section presents an
overview of your mobile phone and
information on the most commonly
used features.
Chapter 1:
Getting
started
Information on how to set up your
mobile phone for the first time:
installation of the SIM card, battery,
etc.
Chapter 2:
Calling
Information on how to make and
receive calls.
Chapter 3:
Text entry
Information on how to enter text
using the numeric keypad.
Chapters 4
to 12
These chapters treat each element of
the
Main Menu one at a time.
Other
sections
After Chapter 12 appear the sections
for Icons & Symbols, Precautions, By-
packed accessories, SAR information
(if available at publication, otherwise
included as a separate document), and
finally the Limited Warranty.

3
Table of contents
1. Getting Started ............................................5
Inserting the SIM card ......................................5
Switching on the phone ...................................6
Charging the battery ........................................7
Setting Hotkeys .................................................7
2. Calling ................................................................8
Make a call ..........................................................8
Answer and end a call ......................................8
Adjust the earpiece volume ............................8
Call handsfree ....................................................8
Options during a call ........................................9
Quick call ......................................................... 10
Handling multiple calls .................................. 10
3. Text Entry ................................................... 12
T9® text input ................................................ 12
Basic text input ............................................... 13
4. Extras .............................................................. 14
Calculator ........................................................ 14
Money converter ........................................... 14
Organiser ......................................................... 14
World clock .................................................... 15
Sound recording ............................................. 16
Alarm clock ..................................................... 17
Infrared ............................................................. 17
Auto Switch On / Off ................................... 18
5. Media Album ............................................. 19
Memory status ................................................ 19
Sound album ................................................... 19
Picture album .................................................. 20
TV slideshow .................................................. 21
6. Entertainment ........................................... 23
Countdown ..................................................... 23
Brick game ....................................................... 23
Java .................................................................... 23
Stopwatch ........................................................ 25
7. Op. Services ............................................... 26
Op. Services + ................................................ 26
WAP ................................................................. 26
8. Messages ....................................................... 29
Settings ............................................................. 29
Create message .............................................. 33
Inbox ................................................................. 36
Outbox ............................................................. 40

4
9. Settings .......................................................... 42
Time and date ................................................. 42
Autonomy ........................................................ 42
Security ............................................................. 43
Profiles .............................................................. 45
Sounds .............................................................. 46
Display .............................................................. 47
Network .......................................................... 48
Shortcuts .......................................................... 49
Language ........................................................... 51
10. Camera ....................................................... 52
How to... .......................................................... 52
Camera menu ................................................. 54
Help ................................................................... 56
11. Address Book ......................................... 57
Copy to phone ............................................... 57
Select contacts ................................................ 57
Delete all .......................................................... 57
Quick call ......................................................... 57
Address book .................................................. 57
Adding a contact ............................................ 59
Service Numbers ............................................ 60
Status ................................................................ 60
12. Call Info ...................................................... 61
Call times ......................................................... 61
Settings ............................................................. 62
Call list .............................................................. 63
Icons & symbols ............................................ 64
Precautions ....................................................... 65
Troubleshooting ........................................... 69
Philips Authentic Accessories .............. 71
Trademark Declaration ............................ 72
Specific absorption rate information .... 73
Limited warranty .......................................... 75

Getting Started 5
1. Getting Started
Please read the safety instructions in the "Precautions"
section before use.
To use your phone, you must insert a valid SIM card
supplied by a GSM operator or retailer. The SIM card
contains your subscription information, your mobile
telephone number, and a memory in which you can
store phone numbers and messages. (see “Address
Book” on page 57)
Inserting the SIM card
Remove the back cover
To insert the SIM card, you must first remove the
back cover. Press down the latch and slide the cover
downwards as shown below.
Remove the battery
To remove the battery, pull the battery up from the
bottom left corner.
You may lose all your personal settings if you remove
the battery when the phone is switched on.
Insert the SIM card
Unlock the SIM card holder and then lift it up on its
hinge (1). Place it in the space provided (2). Make
sure that the clipped corner of the card is in the
correct corner and that the gold contacts are facing
down. Then close the cardholder into the locked
position (3).

6 Getting Started
Slide the battery into its slot, metallic connectors
facing downwards, until it stops. Then lock it by
pushing it downwards.
Replace the back cover by sliding it down into its
slots, until it stops.
Remove the protective film covering the screen and
the camera lens before using the phone.
Switching on the phone
To switch on the phone, long-press the ) key. Enter
the PIN code if required. A PIN code is a 4- to 8-digit
secret code for your SIM card. It is preconfigured and
communicated to you by your operator or retailer. For
more information on PIN codes, see “Security” on
page 43.
If you enter an incorrect PIN code three times, your
SIM card will be blocked. To unblock it, you must
request the PUK code from your operator.

Getting Started 7
When you switch on your mobile phone with your
new SIM for the first time, you will be asked to
customize your phone. This function will help you to
set the following parameters:
Charging the battery
Your phone is powered by a rechargeable battery. A
new battery is partially charged and a sound alert will
warn you when the battery reaches low, if the battery
alert is
On . (see “Sounds alerts” on page 47)
Once the battery and battery cover are back in place
you can charge the phone. Plug in the connector as
shown below. Then plug the other end into a main
AC power socket.
The battery symbol indicates the state of charge. During
charging, the charge indicators will scroll; it takes around
2.5 hours to fully recharge your mobile phone. When all
the scroll bars are steady the battery is fully charged. You
can then disconnect the charger.
Depending on the network and conditionof use, talk time
goes up to 8.5 hours and stand-by time up to 30 days.
Keeping the charger plugged to the mobile when the
battery is fully charged will not damage the battery.
The only way to turn off the charger is to unplug it,
so use an easily accessible AC power socket. You can
connect the charger to an IT supply (Belgium only).
Setting Hotkeys
You can configure the numeric keys 2 to 9 to access
your favourite features simply by long-pressing on the
numeric key. A number of hotkey shortcuts are pre-
configured. For more information, see “Shortcuts” on
page 49
Summer time
Set time
Set date
Melody for incoming calls
Wallpaper
Address Book

8 Calling
2. Calling
Make a call
From the idle screen
1. In idle mode, enter the phone number using the
keypad. To correct an error, press
R <C .
2. Press
( to dial.
3. Press
) or R End call to hang up.
For an international call, long press
* to enter the
"+" sign for the international prefix.
Using the phonebook
1. Press - in idle mode.
2. Select a contact in the list. If you are using the
onboard phonebook and the selected contact
features more than one number, the number
identified as the default will automatically be
selected. To select a different number, press
< or >
(see “Address Book” on page 57 for more
information).
3. Press
( : the selected number is dialled.
4. Press
) or R End call to hang up.
Answer and end a call
When receiving a call, the number of the caller may be
displayed, depending on whether or not the person
calling has chosen to display his or her ID. If the
number is stored in the selected phonebook, then the
corresponding name is displayed instead of the
number.
•Answer the call: press
( .
•Reject the call: press
) . If you have activated Call
forward
(see page 62), the call is diverted to a
number or voice mail.
•Mute the ringer: press
R Silent (this only switches
the sound off without rejecting/accepting the call).
•Hang up: press
) .
The phone will not ring if in Silent mode .
If you have selected
Any Key Answer , you can accept a
call by pressing any key except
) (see “Call forward”
on page 62).
Adjust the earpiece volume
During a call, press the volume keys on the left side of
the phone to increase or decrease the volume.
Call handsfree
For your own comfort and safety, ensure you move the
phone away from your ear when calling handsfree,
especially when increasing the volume.

Calling 9
1. In idle mode, enter the phone number using the
keypad or select a contact in the phonebook.
2. Press
( then L Handsfree .
If you are already on the phone, long press ( to switch
to handsfree mode and back.
Options during a call
During a call, press , or L Options to access the
following options.
Activate h/free
This option allows you to use your mobile phone’s
handsfree option.
Mute / Unmute
Allows you to mute or unmute the microphone so
that your caller cannot hear you.
Record dialogue
In most countries, recording telephone conversations is
subject to legislation. We advise you to notify the caller
if you intend to record your conversation and only do
so if they agree.
To record a conversation during a call, select
Record
dialogue
and press , . Press , again or L Save to end
the recording: an edit window allows you to assign a
name to the recording, which is then available in
Media Album > Sound album > Recordings , and also in
Extras > Sound recording .
Depending on memory capacity (see “Memory status”
on page 19), the number and length of recordings will
vary.
If you select Mute and then Record dialogue , only the
caller’s voice is recorded.
Notepad
Allows you to note down a number. You can then
store it in the phonebook, call it, or send a message to
this number.
Other options during a call
Press L Options to be able to perform the following
tasks while a call is ongoing: you can access and
consult the
Name List or Call list , hang up by selecting
End call , change the Equalizer settings, send or read SMS ,
or consult and manage events of the
Organizer .

10 Calling
Quick call
To access the Quick call feature, press + when in idle
mode. It allows you to set your four most frequently
dialled numbers. You can then quickly call one of
them by selecting the corresponding icon or picture
on the screen.
This feature is also available from the main menu, in
Settings > Shortcuts > Quick call .
Setting a Quick call contact
1. In idle mode, press + to access the Quick call
screen. Select a thumbnail to configure and press
, or L Set .
2. Select a name in the contacts list, and press
,
again to access the Picture album and select a
picture. Proceed the same way for each
thumbnail.
Calling a Quick call contact
To make a call, press + when in idle mode, then select
the thumbnail of your choice and press
, .
To reconfigure a thumbnail, select it and press
, to
Replace the name and/or picture.
If a picture is already associated with a contact, it is
displayed in the
Quick call screen. Changing the picture
in one of the menus will also update it in the other.
Handling multiple calls
The ability to handle two or more calls at one time
and to make conference calls is dependent on your
operator and/or subscription.
Making a second call
You can make a second call during an active call or
with a call on hold. While on the phone, dial a
number (or select a contact in the phonebook) and
press
, . The first call is put on hold (the number is
displayed on the bottom of the screen) and the second
number is dialled. You can then press
, to access the
options among which are:
•
Switch calls to toggle between calls (you can also
press
< or > to switch calls).
•
Transfer to connect the two calls. You are
disconnected when the transfer is completed.
•
Conference to introduce the caller into a conference call.

Calling 11
Answering a second call
When you receive a second call while being already in
communication, the phone emits a beep alert and the
screen displays
Call waiting . You can then:
To receive a second call, you must have deactivated the
Call forward for voice calls (see page 62) and activated
the Call waiting (see page 62).
Answering a third call
If you are in a call and have one call on hold, you can also
receive a third call. To do so, you must either end one of
the calls or introduce the new caller to a conference.
This service is limited to two current communications
(one active and one on hold).
Conference call
Subscription dependent.
A conference call is activated by making several
outgoing calls or from a multiple call context. It
allows you to speak with up to five people at the same
time.
1. Make a first call with someone, then a second
one (see above).
2. Press
, or Options and select Conference . Repeat
the process until five members are connected.
3. Select
Remove party to disconnect a member of
the conference, or select
Private call to have a
private call with this member only (other
members are put on hold).
4. Press
) to disconnect all calls at once.
If there is an incoming call during the conference call
and there are less than five members, you can accept
this new call and add this member to the
Conference
call (if five members are already connected, you can
answer the call, but not add it to the conference).
Press
, To answer the call (the first one is
put on hold).
Press
) To reject the call.
Press
, or L
Options
To open the options list. You can
select
End call to end the current
call, then answer the incoming call.
Press
) To reject the call.
Press
, or L
Options
To open the options list. You can
select
Accept to answer the
incoming call, or
End call to end the
current call, then answer the
incoming call.

12 Text Entry
3. Text Entry
Text can be entered in editing screens in two different
ways: by using T9®Predictive Text Input or basic text
input. The techniques for using these two methods
are discussed below.
T9®text input
T9®Predictive Text Input is an
intelligent editing mode for entering text
on a mobile phone. It allows you to enter
text more quickly by anticipating the
word you want to enter based on the
keys you have pushed. You press once on the key
corresponding to each letter needed to spell a word
and T9®suggests a word based on your keystrokes. If
several words are available, the first word in the list is
displayed and highlighted. Press
+ / - or L to browse
the list and press
, to insert the word.
How to use it?
Letters and symbols represented by each key are as
follows:
Example: how to enter the word "home":
1. Press 4 6 6 3 . The screen displays the first
word of a list:
Good .
2. Press
+ or L to scroll and select Home .
3. Press
, or > to confirm selection of the word
Home .
Dictionary
If the word you want to enter is not in the T9®
dictionary, you can add it to the database. Press L
1>2>3 to scroll to the bottom of the list until you
reach the entry represented by a series of highlighted
underscores (_ _ _ _ _).
2 to 9 To key in letters.
L or
+ / -
To browse the list of candidate words.
Tegic Euro. Pat.
App. 0842463
>
1
,
Press any of the three keys to insert the
selected word followed by a space.
L Short press to backspace, long press to
clear all text.
0 To shift letter case: Standard, lower or
UPPERCASE letters.
# To view the table of symbols and
punctuation. Then press L >> or < and
> to browse the 3 available tables.
* To shift mode from T9®to basic text
input to numeric.

Text Entry 13
Press R Spell to open a basic text editing screen. Enter
the new word without spaces using the methods
described below and press
L OK when done. You are
then returned to the message you were composing and
the new word is inserted.
Language
You can switch input language while writing a
message by long-pressing the
# key. The available
languages will depend on where you purchased your
mobile phone.
Basic text input
Press * to switch from T9®to basic text input. This
method requires multiple key presses to reach the
desired character: the letter "h" is the second letter on
the 4 key, so you must press it twice to enter "h".
Short press
R Cancel to clear one entry, long press to
clear all text.
Example: how to enter the word "home":
Press 4 , 4 ( G H I ) 6 , 6 , 6 ( MN O), 6 (M NO ),
3 , 3 ( D E F ). Press , when the message is
completed.
Letters, numbers and symbols are located on each key
as described opposite.
Short press Long press
1
space 1. , @ / : ; " ’ ! ¡ ? ¿ # + - *
= % < > ( ) & £ $ ¥ 1
2 a b c 2 à ä å æ ç 2
3 d e f 3 é è ∆Φ3
4 g h i 4 Γì 4
5 j k l 5 Λ5
6 m n o 6 ñ ò ö 6
7 p q r s 7 βΠΘΣ7
8 t u v 8 ü ù 8
9 w x y z 9 ø ΩΞΨ9
0
To shift letter case: Standard,
lower or UPPERCASE letters. 0
#
To open symbols and
punctuation mode. Then press
L >> or < and > to browse the
3 available tables.
Changes the
language
used for text
edition
*
To shift mode: T9®, basic or
numeric. Also shifts mode

14 Extras
4. Extras
This menu contains features and options designed to
help you keep you organised and informed while on
the move.
Calculator
Your phone has a built-in calculator that you
can use to perform basic calculations.
Numbers are entered with the keypad and
operators with the navigation keys as
indicated in the table below:
An icon at the top of the screen indicates which
navigation keys to use for entering operators.
Press and hold
0 to get the decimal point.
The result of the calculator is indicative. The
calculation accuracy is 2 decimal places. The result is
then truncated after the 2nd decimal digit for the next
operation.
Money converter
This menu allows you to convert a sum from
one currency into another using the exchange
rate of your choice. You can convert from
Local to Foreign or vice versa. Enter a rate in the
Exchange rate field and an amount in either the Local or
Foreign fields: the sum is calculated automatically.
Organiser
This menu allows to create, store and manage
events in your organiser. When the organiser
alert is
On (see “Sounds alerts” on page 47), a
beep alerts you when an event is due.
The organiser shares the mobile memory capacity with
other features (phonebook, picture album, sound,
etc.). To check the memory available in your phone,
select Media Album > Memory status.
Creating a new event
1. In Events , select <New> , then the type of event to
create (
Holiday , Meeting , To Do ).
2. Enter the starting and ending date and time of the
event and name it (e.g. "Meeting with Smith").
3. Set a reminder and a frequency: alerts will be
triggered at the chosen time.
Addition Press > or the * key.
Subtraction Press < or the * key twice.
Multiplication Press + or the * key 3 times.
Division Press - or the * key 4 times.
Equals Press , or # .

Extras 15
The reminder only applies to Meeting and To Do events.
It will be updated when changing time zones (see
“World clock” below).
Deleting old events
This menu allows you to delete past events. Enter the
starting date (past or future) from which all previous
events will be deleted and press
, twice to delete all
events preceding this date.
To delete all events set in your organiser, enter a
starting date several years ahead (e.g. 31st of
December 2010) to make sure all events preceding this
date are deleted at once.
Managing events
Select an event in the list and press , or L Options to
access the options described below.
Changing a repeating event modifies all instances of
this event.
Events views
Events stored in your organiser can be displayed in
Day view , Week view and Month view . Select a view
format and press
, , then use < or > to display the
previous or next day, week or month.
World clock
This menu allows you to set and display both
the local time and the time in the foreign time
zone of your choice. Note that if you choose
to display the local and foreign time on your home
screen, the image you selected as your wallpaper will
no longer be displayed there, but will be replaced with
the standard World clock wallpaper.
Local settings
Delete To delete the selected event.
Change To change the selected event.
Send by
infrared
To transmit the selected event to
another infrared-compatible device.
Change
sound
To change the sound associated with
the alarm type of the selected event.
Set time Allows you to set the time by
pressing the appropriate keys.
Local zone Move + or - to select the time
zone corresponding to your area.
Summer time Allows you to set summer time
option
On or Off for the local
time zone.

16 Extras
World clock
Activate this option if you want to display both the
local time and the time of another time zone on the
idle screen. Press
+ or - to set the option On or Off .
When
On , you can display the zone of your choice via
the menu
Switch local / foreign .
This feature is not available when the option No clock
is selected in “Set date” on page 42.
Switch local / foreign
To display local to foreign zone and vice-versa.
Foreign settings
Alarms, reminders, programmed events are time zone
independent! If you set an alarm or an event at
9:00 AM in time zone A, it will still ring or be due at
9:00 AM if you change to time zone B.
Sound recording
This menu allows you to make recordings of
up to 12 minutes in length, depending on the
memory status (see “Memory status” on
page 19).
Select
<New> to begin the recording. When you are
finished, press
L Save to stop recording. You can then
either enter a name for the new sound file or accept
the default name proposed by pressing
, . You then
return to the list of
Sound recordings and the new
recording is displayed in the list.
When you select a sound file, it is played
automatically in a loop. Press
, to access the options.
You can
Play recording , Rename or Delete it, set as ringer
or As SMS/MMS ringer .
A flashing warning sign indicates that your recording
will soon reach the maximum authorized length. If
you do not stop recording, a red envelope icon informs
you that your recording is too long to be sent via MMS.
Foreign
zone
Move + or - to select the time zone of
your choice.
Daylight
saving
Allows you to set the daylight saving
option
On or Off for a foreign time zone.

Extras 17
Alarm clock
Our mobile phone has a built-in alarm clock
with a snooze feature. You can set up to three
separate alarms and choose whether or not
the alarm should repeat. To set an alarm, follow the
steps below:
1. Select an alarm and set it
On .
2. Then enter the time and press
, .
3. Then select the frequency:
Once , daily , On
weekdays
.
4. Finally, select the type of alarm: the
Buzzer or a
melody from the sounds album and press
, .
Repeat above steps to set other alarms.
The alarm clock will ring even if your mobile phone is
switched off and/or the ringer volume is set to
Silent .
When the alarm rings, press any key to stop it (except
if the snooze mode is on, see below).
Snooze mode
This menu allows you to set the snooze mode On or
Off . When the alarm rings and the snooze mode is On :
• press any key (except
R Stop ) to stop the ringing
temporarily. The alarm will ring again around 7
minutes later.
• press
R Stop to stop the ringing and the alarm
repetition.
The snooze mode is automatically deactivated after 9
alarm repetitions.
The snooze mode setting applies to all the alarms you
have set.
Infrared
Your mobile phone allows you to connect to
a variety of external devices via infrared. This
menu provides you with more features to set
up the connection with these external
devices.
Infrared
Your mobile phone has an infrared port that allows
you to send or receive data to or from other infrared-
compliant devices (e.g. another mobile phone, a
computer, a PDA, etc.) through a wireless link.
Files that are copyright protected cannot be sent.
When connecting with a PC, make sure you have
activated its infrared option.
Position of devices
Before transmitting data between two devices, they
must be correctly positioned in relation to one
another. Make sure that:

18 Extras
• the infrared ports are facing each other,
• they are at a less than 50 cm away from each other.
• nothing obstructs the infrared beam.
Sending data
To send data via infrared from your mobile phone, you
must first select the item to be sent: when selecting a
picture, a sound, a name or an event, a sub-menu then
gives you access to the
Send via infrared option.
As soon as your phone finds another infrared
compliant device to communicate with, the sending
automatically takes place. Messages are displayed on
the screen for you to follow the process.
Sending is cancelled if your phone cannot find another
device before the time out is reached, if the infrared
link is broken, or if you cancel the process.
Receiving data
When you select
Receive your phone is ready to receive
an item via infrared and waits for the another infrared
device to send it. As with sending data, messages are
displayed on the screen and allow you to follow the
process.
Receiving is cancelled if your phone isn’t contacted by
another device before the time out is reached, if the
infrared link is broken, if the size of the file sent is too
large or if you cancel the process.
Saving the data
A message will appear to inform you that you have
received a file. Press
, to access the options described
below.
Auto Switch On / Off
These two separate menus allow you to set your
mobile phone to switch itself on or off at pre-set times.
This lets you extend your phone’s battery life (e.g.
during the night), not be disturbed at given times and
have your phone switch back on automatically.
To set
Auto switch on , select the option and press , .
Select
On and press , . Enter the time at which you
want your mobile phone to switch itself on and press
, . Select the desired frequency from Once , daily , or On
weekdays
and press , . A message appears to confirm
activation.
Save To save the data, eventually rename the
file.
Show To display the details of the data you
have received.
Discard To ignore the data received.

Media Album 19
5. Media Album
Memory status
This menu allows you to display the
percentage of memory available in your
phone. Various features share the memory
capacity: pictures, sounds, recorded memos and voice
tags for voice commands, stored messages, phonebook
and organiser entries, games, etc.
Press
, to check the memory status. The display
shows you the percentage of memory free and the
phone’s total memory in Kilobytes (Kb). Press
,
again to check the detailed list of memory used by
each feature.
Your mobile phone is supplied with many sounds and
pictures. You can only delete sounds or pictures which
are not protected, e.g. to free memory space for your
own sounds and pictures.
If the
List full message appears when saving a new item
you must delete an item to be able to create or add a
new one.
Sound album
This menu allows you to manage the sound
files stored in your mobile phone. The
options are:
Once in a list, you can then select a sound file and
press
, to access the menu options listed below.
View all To access all your sound files in a
single list.
Own melodies To access your downloaded sound
files.
Protected
melodies
To access the list of copyright
protected sample sounds.
Protected melodies cannot be sent
nor deleted.
Recordings To access the list of sound
recordings.
Send by... To send the selected sound file via
E!mail (see page 31), via Infrared (see
page 17) or
MMS (see page 39).
As ringtone To set the selected sound as ringer.