Philips AJB4700 User manual

AJB4700
www.philips.com/welcome
Register your product and get support at
Question?
Contact
Philips
Always there to help you
User manual
a
bd
ce
AJB4700
User Manual
www.philips.com/welcome
Always there to help you
Registeryour product and get support at
3 sec.
f
3 sec.
1 Important
• Read these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
• Do not install near any heat sources such as radiators, heat registers,
stoves,orotherapparatus(includingampliers)thatproduceheat.
• Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point where
they exit from the unit.
• Onlyuseattachments/accessoriesspeciedbythemanufacturer.
• Use only power supplies listed in the user manual.
• Unplug this unit during lightning storms or when unused for long
periods of time.
• Referallservicingtoqualiedservicepersonnel.Servicingisrequired
when the unit has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen
into the unit, the unit has been exposed to rain or moisture, does
not operate normally, or has been dropped.
• This unit shall not be exposed to dripping or splashing.
• Donotplaceanysourcesofdangerontheunit(e.g.liquidlled
objects,lightedcandles).
• Where the plug of the Direct Plug-in Adapter is used as the
disconnect device, the disconnect device shall remain readily operable.
Warning
•Never remove the casing of this clock radio.
•Never lubricate any part of this clock radio.
•Never place this clock radio on other electrical equipment.
•Keepthisclockradioawayfromdirectsunlight,nakedamesorheat.
•Make sure that you always have easy access to the power cord, plug or
adaptor to disconnect the clock radio from the power.
2 Your FM/DAB+ clock radio
Congratulations on your purchase, and welcome to Philips!To fully
benetfromthesupportthatPhilipsoffers,registeryourproductat
www.philips.com/welcome.
Introduction
With this clock radio, you can
• listentoFMandDigitalAudioBroadcasting(DAB+)radio;and
• set two alarms.
What's in the box (Fig. )
3 Get started
Always follow the instructions in this chapter in sequence.
Prepare FM/DAB+ antenna
For better reception, fully extend and adjust the position of the FM/
DAB+ antenna. (Fig. )
Note
•To prevent interference, position the antenna as far as possible fromTV,VCR,
or other radiation source.
Connect power
Caution
•Risk of product damage! Make sure that the power supply voltage
corresponds to the voltage printed on the back or the underside of the
clock radio.
•Risk of electric shock! Hold the plug securely when unplugging the adapter.
Note
•The type plate is located on the bottom of the clock radio.
(Fig. )
Turn on
Press POWER.
» The clock radio switches to the last selected source.
Switch to standby mode
Press and hold POWER for 3 seconds.
» Theclock(ifset)appearsonthedisplaypanel.
Set time
1 In standby mode, press and hold INFO for 3 seconds to activate the
time setting mode. (Fig. )
» The hour digits blink.
2 Press / to adjust the hour.
3 Press INFOtoconrm.
» The minute digits blink.
4 Repeat steps 2-3 to set the minute.
5 Repeat steps 2-3 to set the day, month, and year.
Tip
•To adjust the 12/24 hour format, see "Use system menu" > "Set hour
format and synchronize time".
•When being idle for 10 seconds, the clock radio exits clock setting mode
automatically.
4 Listen to DAB+ radio
DigitalAudioBroadcasting(DAB+)isawayofbroadcastingradio
digitally through a network of transmitters. It provides you with more
choice, better sound quality and more information.
For the rst time use
1 Press SOURCE repeatedly to select DAB+ radio.
» [FULL SCAN](fullscan)isdisplayed.
2 Press SELECT to start full scan.
» The clock radio stores all DAB+ radio stations automatically and
thenbroadcaststherstavailablestation.
» The station list is memorized in the clock radio.When you turn
on the unit next time, the station scan does not take place.
» If no DAB+ station is found, [No DAB Station](noDABstation)
is displayed.
To tune to a station from the station list:
In DAB+ mode, press TUNING / repeatedly to navigate through
the available DAB+ stations.
» If the signal of the DAB+ radio station is too weak, [OFF AIR] (off
air)isdisplayed.
Store DAB+ radio stations automatically
Tip
•New stations and services will be added in the DAB+ broadcast.To make
new DAB+ stations and services available, perform full scan regularly.
In DAB+ mode, press and hold SCAN for 3 seconds.
» The clock radio stores all the available DAB+ radio stations automatically.
» Afterfullscan,therstavailablestationisbroadcast.
Store DAB+ radio stations manually
You can store up to 10 DAB+ radio stations.
1 Tune to a DAB+ radio station.
2 Press and hold PRESET for 3 seconds to activate the storing mode.
3 Press TUNING / to select a number.
» The preset number is displayed for one second.Then if this position
is occupied, the previously stored DAB+ station name will be
displayed;ifthispositionisempty,[Empty] will be displayed.
4 Press PRESETtoconrm.
5 Repeat steps 1-4 to store other DAB+ stations.
Note
•To remove a pre-stored DAB+ radio station, store another station in its
place.
Listen to a preset DAB+ radio station
In DAB+ mode, press PRESET repeatedly to select a preset radio
station.
Use DAB+ menu
1 In DAB+ mode, press and hold MENU for 3 seconds to access
DAB+ menu.
2 Press TUNING / to scroll through the menu options:
• [STATION]: Display a list of available DAB+ stations.
• [FULL SCAN]:ScanandstoreallavailableDAB+radiostations.
• [MANUAL]:Tunetoaspecicchannel/frequencymanuallyand
add it to the station list.
• [DRC](DynamicRangeControl): Add or remove a degree of
compensation for differences in the dynamic range among DAB+
stations.You may experiment the options on different source
materials to decide which option suits best.
• [PRUNE]: Remove invalid stations from the station list.
• [SYSTEM]:Adjust system settings (see the Chapter "Use system
menu").
3 To select an option, press SELECT.
4 Repeat steps 2-3 if sub-option is available under one option.
[DRC]
• [DRC OFF]: No compensation applied.
• [DRC HIGH]: Maximum compensation applied (the default
optionrecommendedfornoisyenvironment).
• [DRC LOW]: Medium compensation applied.
[PRUNE]
• [PRUNE N]: Return to the previous menu.
• [PRUNE Y]: Remove invalid stations from the station list.
Show DAB+ information
While listening to DAB+ radio, press INFO repeatedly to scroll through
thefollowinginformation(ifavailable):
» Stationname
» DynamicLabelSegment(DLS)
» Signalstrength
» Programtype(PTY)
» Ensemble Name
» Frequency
» Signalerrorrate
» Bitrate
» Codec
» Time and date
5 Listen to FM radio
Tune to FM radio stations
1 Press SOURCE repeatedly to select FM radio.
2 Press and hold TUNING / for 3 seconds.
» The FM tuner tunes to a station with strong reception
automatically.
To tune to a radio station manually:
Press TUNING / repeatedly to tune to a radio station.
AJB4700_79_UM_V1.0.indd 2-6 2013/6/26 17:39:02

Store FM radio stations automatically
In FM tuner mode, press and hold SCAN for 3 seconds.
» The clock radio stores all the available FM radio stations
automatically.
» Therststoredradiostationisbroadcast.
Store FM radio stations manually
You can store up to 10 FM radio stations.
1 Tune to an FM radio station.
2 Press and hold PRESET for 3 seconds to activate the storing mode.
3 Press TUNING / to select a number.
» The preset number is displayed for one second.Then if this
position is occupied, the previously stored radio frequency will be
displayed;ifthispositionisempty,[Empty] will be displayed.
4 Press PRESETtoconrm.
5 Repeat steps 1-4 to store more FM stations.
Tip
•To remove a pre-stored FM radio station, store another station in its place.
Select a preset FM radio station
In FM mode, press PRESET repeatedly to select a preset radio channel.
Use FM menu
1 In FM mode, press and hold MENU for 3 seconds to access FM
menu.
2 Press / to scroll the menu options:
• [SCAN SETTINGS]
• [SYSTEM] (see the Chapter "Use system menu")
3 To select an option, press SELECT.
4 Repeat steps 2-3 if sub-option is available under one option.
[SCAN SETTINGS]
• [ALL]:ScanalltheavailableFMradiostations.
• [STRONG]:ScanFMradiostationswithstrongsignalsonly.
Show RDS information
RDS(RadioDataSystem)isaservicethatallowsFMstationstoshow
additional information.
1 TunetoanRDSstation.
2 Press INFO repeatedly to scroll through the following information
(ifavailable):
» Stationname
» Radio text messages
» Program type such as [NEWS](news),[SPORT](sport),[POP
M](popmusic)...
» Frequency
» Time and date
RDS program types
Program type Description Program
type
Description
NEWS News services FINANCE Finance
AFFAIRS Politics and current
affairs
CHILDREN Children's
programs
INFO Specialinformation
programs
SOCIAL Socialaffairs
SPORT Spor ts RELIGION Religion
EDUCATE Education and advanced
training
PHONE IN Phone in
DRAMA Radio plays and
literature
TRAVEL Tr a ve l
CULTURE Culture, religion and
society
LEISURE leisure
SCIENCE Science JAZZ Jazz Music
VARIED Entertainment programsCOUNTRY Country
Music
POP M Pop music NATION M National
Music
ROCK M Rock music OLDIES Oldies Music
MOR M Light music FOLK M Folk Music
LIGHT M Light classical music DOCUMENT Documentary
CLASSICS Classical music TEST Alarm Test
OTHER M Specialmusicprograms ALARM Alarm
WEATHER Weather
6 Use system menu
Use the system menus to
• set12/24hourformat;
• selectwhethertosynchronizetimefromtheDAB+stations;
• checkthesoftwareversionofthisclockradio;and
• reset the clock radio to factory default status.
Set hour format and synchronize time
1 Enter the system menu (see "Listen to DAB+ radio" > "Use DAB+
menu" or "Listen to FM radio" > "Use FM menu")
2 Press / to select [TIME].
3 Press SELECTtoconrm.
4 Repeat steps 2-3 to select a sub-option.
Options Sub-
option
Function
[UPDATE] [DAB] SynchronizetimefromDAB+stations.
[NONE] Deactivate time synchronization.
[12/24 HR] [12] Display time in 12-hour format.
[24] Display time in 24-hour format.
Reset all the settings
1 Enter the system menu.
2 Press / to select [RESET].
3 Press SELECTtoconrm.
4 Press / to select an option.
• [RESET N]: Return to the previous menu.
• [RESET Y]: Reset the radio to factor y default status.
5 Press SELECTagaintoconrm.
Know the software version
1 Enter the system setting menu.
2 Press / to select [SW VER](Softwareversion).
3 Press SELECTtoconrm.
» The software version of the clock radio is displayed.
7 Other features
Set the alarm timer
You can set two alarms to ring at different time. (Fig. )
Note
•Make sure that you have set the time correctly.
1 Press and hold AL1 or AL2 for 3 seconds to activate alarm setting
mode.
» The alarm icon and the hour digits blink.
2 Press / repeatedly to set the hour.
3 Press AL1 or AL2toconrm.
» The minute digits blink.
4 Repeat steps 2-3 to set the minute.
5 Repeat steps 2-3 to set the alarm source: DAB, FM or buzzer.
6 Repeat steps 2-3 to set the alarm volume.
» The alarm icon is displayed.
Tip
•When alarms sounds, volume rises gradually.
•If DAB is selected as alarm source, while no DAB+ radio station is available,
buzzer is activated when alarm time comes.
Activate/deactivate the alarm timer
1 Press AL1/AL2 to view alarm settings.
2 Press AL1/AL2 repeatedly to activate or deactivate the alarm timer.
» The alarm icon appears if the alarm timer is on and disappears
if it is off.
• To stop the ringing alarm, press the corresponding AL1/AL2.
» The alarm repeats ringing for the next day.
Snooze the alarm
When alarm sounds, press SNOOZE.
» The alarm snoozes and repeats ringing nine minutes later.
Set the sleep timer
This clock radio can switch to standby mode automatically after a preset
period.
Press SLEEPrepeatedlytoselectthesleeptimerperiod(inminutes).
» When the sleep timer is activated, appears.
To deactivate the sleep timer:
• Press SLEEP repeatedly until [OFF] (off)appears.
Adjust volume
Press VOLUME / . (Fig. )
15 30 60 90 120
OFF
August 2011
Philips Electronics Australia Limited and Philips New Zealand Limited
Warranty against Defects
In this warranty: We or us means Philips Electronics Australia Limited ACN 008 445 743 or Philips New Zealand Limited (Company
Number 1723), and our contact details are set out at the end of this warranty; You means the purchaser or the original end-user of the Goods; Supplier means the authorised distributor or retailer of the Goods that sold you the Goods in Australia or New Zealand; and Goods means the product or equipment which was accompanied by this warranty and purchased in Australia or New Zealand. If you require assistance with the operation of the product, its features or specifications please call the Philips Consumer Care Centre on 1300 363 391 in Australia or 0800 658 224 in New Zealand. Australia: Our Goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonabl y foreseeable loss or damage. You are also entitled to have the Goods repaired or replaced if the good s fail to be of acceptable quality and the failure does not amount to a major failure. This is not a complete statement of your legal rights as a consumer. New Zealand: Our Goods come with guarantees that cannot be excluded under the Consumer Guarantees Act 1993.
This guarantee applies in addition to the conditions and guarantees implied by that legislation. Additional Warranty: In addition to the rights and remedies that you have under the Australian Consumer Law, Consumer Guarantees Act of New Zealand or any other applicable law, we provide the following warranty against defects: 1. If, during the first 12 months from their date of purchase from the Supplier (Warranty Period), the Goods prove
defective by reason of improper work manship or materials and none of your statutory rights or remedies apply, we will repair or replace the Goods without charge.
2. We do not have to repair or replace the Goods under this Additional Warranty if the Goods have been u sed for a
commercial purpose; misused, improperly or inappropriately installed, operated or repaired; abu sed; damaged; or not maintained in accordance with the manufacturer’s instructions.
3. Even when we do not hav e to repair or replace the Goods, we ma y decide to do so an yway. In some cases, we
may decide to substitute the Goods with a similar alternative prod uct of our choosing. All such decisions are at
our absolute discretion.
4. All such repaired, replaced or substituted Goods contin ue to receive the benefit of this Additional Warranty for the
time remaining on the original Warranty Period.
5. This Additional W arranty is limited to repair, replacement or substitution only. As far as the law permits, we will not
be liable for any loss or damage caused to property or persons arising from any cause whatsoever.
6. In order to claim under this Additional Warranty you must telephone us on 1300 363 391 in Australia or 0800 658
224 in New Zealand within the Warrant y Period. You will be asked for details of the Goods, a descripti on of the defect and your personal details. Upon accepting your claim, we shall assist you with either returning the Goods to the Supplier for replacement or to the most convenient Philips Authorised Service Centre for your Goods to be repaired. In some case we may require that you return to the Goods to us (at the address below) for repair, replacement or substitution.
∗All returned Goods must be accompanied by satisfactory proof of purchase which clearly indicates the name and
address of the Supplier, the date and place of purchase and identifies product. It is best to provide a legible and
unmodified receipt or sales invoice.
∗You must bear any expense for return of the Goods or otherwise associated with making your claim under this
Additional Warranty.
7. This warranty is onl y valid and enforceable in Australia and New Zealand.
Contact us or the place of purchase for further details. Philips Electronics Australia Limit ed Philips New Zealand Limited
Level 1, 65 Epping Rd, Level 2, 1 Nugent St, North Ryde, SYDNEY NSW 2113 Grafton, AUCKLAND, 1
023
Consumer Care: 1300 363 391 Consumer Care: 0800 658 224 E-mail: [e-mail] Email: [e-mail]
Website: www.philips.com/support Websit e: www.philips.com/support
Adjust display brightness
Press BRIGHTNESS repeatedly to select different brightness levels.
8 Product information
Note
•Product information is subject to change without prior notice.
Amplier
Rated Output Power 0.5WRMS
Tuner
FM:
Tuning Range FM: 87.5 - 108 MHz
Tuning Grid 50 KHz
Sensitivity
-Mono,26dBS/NRatio
<22 dBf
SearchSelectivity 25-32 dBf
Total Harmonic Distor tion < 2%
SignaltoNoiseRatio >50 dBA
DAB:
Tuning Range 174.92-239.20MHz
Total Harmonic Distor tion <2%
SignaltoNoiseRatio >55 dBA
General information
AC Power (Model) SSW-1920AU-3(Philips)
(Input) 100-240 V ~, 50/60 Hz,
0.2 A
(Output) 6 V 0.5 A
Operation Power Con-
sumption
< 3 W
StandbyPowerConsump-
tion
<1 W
Dimensions - Main Unit (W
xHxD)
152 x 62 x 109 mm
Weight - Main Unit 0.3 kg
9 Troubleshooting
Warning
•Never remove the casing of this product.
To keep the warranty valid, never try to repair the product yourself.
If you encounter problems when using this product, check the following
points before requesting service. If the problem remains unsolved, go
tothePhilipsWebpage(www.philips.com/support).Whenyoucontact
Philips, make sure that the product is nearby and the model number
and serial number are available.
No power
• Make sure that the power adapter is connected properly.
• Make sure that there is power at the AC power outlet.
No sound
•Adjust the volume.
No response from the unit
•Make sure that the unit is connected to power.
•Disconnect and reconnect the AC power plug, then turn the unit
on again.
Poor radio reception
•Increase the distance between the unit and yourTV or VCR.
•Fully extend the antenna.
10 Notice
Anychangesormodicationsmadetothisdevicethatarenotexpressly
approved by Philips Consumer Lifestyle may void the user’s authority to
operate the equipment.
Disposal of your old product
Your product is designed and manufactured with high quality materials
and components, which can be recycled and reused.
Never dispose of your product with other household waste. Please
inform yourself about the local rules on the separate collection
of electrical and electronic products.The correct disposal of these
products helps prevent potentially negative consequences on the
environment and human health.
Please visit www.recycle.philips.com for additional information on a
recycling center in your area.
Environmental information
All unnecessary packaging has been omitted. We have tried to make
thepackagingeasytoseparateintothreematerials:cardboard(box),
polystyrenefoam(buffer)andpolyethylene(bags,protectivefoam
sheet.)
Your system consists of materials which can be recycled and reused
if disassembled by a specialized company. Please observe the local
regulations regarding the disposal of packaging materials, exhausted
batteries and old equipment.
ThisisCLASSIIapparatuswithdoubleinsulation,andnoprotective
earth provided.
Note
•The type plate is located on the bottom of the product.
All registered and unregistered trademarks are
property of their respective owners.
© 2013 Koninklijke Philips Electronics N.V.
All rights reserved.
AJB4700_79_UM_V1.1
AJB4700_79_UM_V1.0.indd 11-12 2013/6/26 17:39:05