Philips R3505 User manual

Register your product and get support at
www.philips.com/support
User manual
Clock Radio
3000 Series
R3505

1
EN
Contents
1 Important 2
Safety 2
2 Yourclock radio 3
Introduction 3
What's in the box 3
Overview of the clock radio 3
3 Get started 4
Install batteries 4
Connect power 4
Set time 4
Turn on 4
4 Listen to DAB+ radio 5
Tune to DAB+ radio stations 5
Store DAB+ radio stations automatically 5
Store DAB+ radio stations manually 5
Select a preset DAB+ radio station 5
Show DAB+ information 5
Use DAB+ menu 6
5 Listen to FM radio 6
Tune to FM radio stations 6
Store FM radio stations automatically 6
Store FM radio stations manually 6
Select a preset radio station 7
Show RDS information 7
Use FM menu 7
6 Other features 8
Set alarm time 8
Set sleep timer 8
Adjust volume 8
Adjust display brightness 8
7 Product information 9
8 T roubleshooting 9
9 Notice 10

2EN
1 Important
Safety
Warning
•Never remove the casing ofthis clock radio.
•Never lubricate any part ofthis clock radio.
•Never place this clock radio on other
electrical equipment.
•Keep this clock radio away from direct
•Make sure that you always have easy access
to the power cord, plug oradaptorto
disconnect the clock radio from the power.
•Read theseinstructions.
•Heed all warnings.
•Follow all instructions.
•Do not block any ventilationopenings. Install in
accordance withthe manufacturer’s instructions.
•Do not install near any heat sourcessuch as
radiators, heat registers, stoves,orother apparatus
•Protect the power cord from being walked on
or pinched,particularly at plugs,convenience
receptacles, and the point where they exit
from the clock radio.
•
the manufacturer.
•Unplug this apparatus during lightning storms
or when unused for long periods oftime.
•
personnel. Servicing is required when the
apparatus has been damaged inany way, such
as power-supply cord orplug is damaged,
liquid has been spilled orobjects have fallen
into the apparatus,the apparatus has been
exposed to rainormoisture, does not operate
normally, or has been dropped.
•Battery usage CAUTION -To prevent battery
leakage which may result inbodily injury,
property damage, ordamageto the clock radio:
•Install all batteries correctly, + and - as
marked on the unit.
•Remove batteries when the unit is not
used for a long time.
•The battery shall not be exposed to
the like.
•This clock radio shall not be exposed to
dripping or splashing.
•Do not place any sourcesofdangeronthe
•Where the plug ofthe Direct Plug-in
Adapter is used as the disconnect device,
the disconnect device shall remain readily
operable.

3
EN
2 Your clock radio
Congratulations on your purchase, and
support that Philips offers, register your product
at www.philips.com/support.
Introduction
With this clock radio, you can
•listen to both FM and Digital Audio
Broadcasting (DAB+) radio;
•set two alarms to ring at different times.
What's in the box
Check and identify the contents of your package:
•Main unit
•AC power adaptor
•Quick start guide
•
Quick start guide
TAPR802
Overview of the clock radio
•Turn on or switch to standby.
PRESET / SET TIME
•Store radio stations in memory.
•Select a preset FM station or DAB station.
•Set time.
HR / MIN / TUN
•Tune to radio stations.
•Set hour and minute.
SNOOZE / BRIGHTNESS
•Snooze alarm.
•Adjust display brightness.
Display panel
•Display current status.
AL1 / AL2 / VOL
•Set alarm.
•Adjust volume.
MENU / INFO
•Enter the DAB+ menu.
•Display DAB/RDS station information.
SCAN / SELECT
•Scan/store radio stations automatcially.
•
SLEEP
•Set the sleep timer.
FM / DAB
•Select FM or DAB+ mode.
1
2
3
6
7
9
8
5
4
10

4EN
3 Get started
Always follow the instructions in this chapter in
sequence.
Install batteries
The batteries can only back up clock and alarm
settings.
Caution
•Risk of explosion! Keep the batteries away from heat,
•Batteries contain chemical substances, so they should
be disposed of properly.
Insert 2 AAA batteries (not provided) with
correct polarity (+/-) as illustrated.
Connect power
Caution
•Risk of product damage! Make sure that the power
voltage corresponds to the voltage printed on the back
or underside of the clock radio..
•Risk of electrical shock! When you unplug the power
adapter, always pull the plug from the socket. Never
pull the cord.
•
manufacturer or sold with this unit.
Note
•The type plate is located at the bottom of the clock radio.
Set time
Note
•You can only set time in standby mode.
1 In standby mode, press and hold SET TIME
for more than 2 seconds.
2 Press TUN to select <24 HR> or
<12 HR> hour format, then press SET TIME
3 Press HR to set hour and MIN to set minute,
then press SET TIME
4 Press TUN to set date, month and
year [DD-MM-YY], then press SET TIME to
5 Press TUN to select <UPDATE FROM
RADIO> or <NO UPDATE>, then press
SET TIME
[SAVED] is displayed and the time is set.
Turn on
Press to turn on the clock radio.
The unit switches to the last selected
source.
To switch to standby mode, press again.
The real-time clock is displayed.

5
EN
4 Listen to DAB+
radio
Tune to DAB+ radio stations
1 Press to turn on the clock radio.
2 Press DAB / FM repeatedly to select DAB
mode.
[DAB] will be displayed for more than 2
seconds and a DAB icon will be turned on.
The unit will tune to the last tuned station
and display the station name.
PRESS SELECT TO
SCAN] will be displayed.
3 Press SCAN / SELECT.
The unit stores all DAB+ radio stations
available station.
If no DAB+ station is found, [NO SIG] (no
To tune to a station from the available stationlist:
In DAB mode, press TUN repeatedly
to navigate through the available DAB+
stations.
Store DAB+ radio stations
automatically
In DAB mode, press and hold SCAN / SELECT
for more than 2 seconds.
The unit scans all the available DAB+ radio
station.
Tip
•No DAB+ radio station is stored to presets during this
process.
•New stations and services will be added in the DAB+
broadcast.To make new DAB+ stations and services
available, perform a full scan regularly.
Store DAB+ radio stations
manually
Note
•You can store a maximum of 20 preset DAB+ radio
stations.
1 Tune to a DAB+ radio station.
2 Press and hold PRESET for more than 2
seconds to acitvate programming mode.
3 Press TUN repeatedly to select a number.
4 Press PRESET
5 Repeat steps 1 to 4 to store more DAB+
radio stations.
Note
•To remove a preset DAB+ radio station, store another
station in its place.
Select a preset DAB+ radio
station
1 In DAB mode, press PRESET.
2 Press TUN repeatedly to select a preset
radio station, then press SELECT
Show DAB+ information
Whilelistening to DAB+ radio, press MENU / INFO
repeatedly to scroll through the following
•Station name

6EN
•
•Signal strength
•
•Ensemble Name
•Channel and frequency
•Signal error rate
•Bit rateand audio status
•Time
•Date
Use DAB+ menu
1 In DAB mode, pressand hold MENU/ INFO for
more than 2 seconds to access the DAB+ menu.
2 Press TUN to scroll through the menu
options:
•[Scan]: scan all the available DAB+ radio
stations.
•[Manual
frequency manually and add it to the
stationlist.
•[DRC]: add or remove a degree of
compensation for the differences in the
dynamic range between radio stations.
•[Prune]: remove all the invalid stations
from the station list.
•[System]: adjust system settings.
3 To select an option, press SELECT.
4 Repeat steps 2-3 if any sub-option is available
under an option.
[System]
•[Reset]: reset all the settings to factory default.
•[SW VER
software versionofthe unit.
•[Language]: set system language (English
/ Deutsch / Itliano / Français / Norsk /
Note
•If no button is pressed within 15 seconds, the menu
will exit.
5 Listen to FM radio
Note
•Keep the clock radio away from other electronic devices
to avoid radio interference.
•For better reception, fully extend and adjust the position
of the FM antenna.
Tune to FM radio stations
1 Press to turn on the clock radio.
2 Press FM / DAB repeatedly to select FM
radio.
3 Press and hold TUN for more than 2
seconds.
The clock radio tunes to a station with
strong receptionautomatically.
4 Repeat Step 3to tune to more radio stations.
To tune to a station manually:
In FM tuner mode, press TUN repeatedly
to select a frequency.
Store FM radio stations
automatically
In FM tuner mode, press and hold SCAN for
more than 2 seconds.
The unit stores all the available FM radio
stations automatically and broadcasts the

7
EN
Store FM radio stations manually
Note
•You can store a maximum of 20 FM radio stations.
1 Tune to an FM radio station.
2 Press and hold PRESET for more than 2
seconds to activate programming mode.
3 Press TUNrepeatedly to select a number.
4 Press PRESET
5 Repeat steps 1 to 4 to store more FM radio
stations.
Tip
•To remove a pre-stored station, store another station
in its place.
Select a preset radio station
1 In FM tuner mode, press PRESET.
2 Press TUN repeatedly to select a preset
radio station, then press SELECT
Show RDS information
allows FM radio stations to show additional
information.
While listening, press MENU / INFO repeatedly
to scroll through the following information (if
•Station frequency
•Station name
•Program name
Use FM menu
1 In FM tuner mode, press and hold MENU /
INFO for more than 2 seconds to access the
FM menu.
2 Press TUN to scroll through the menu
options:
•[Scan]: scan settings.
•[System]: adjust system settings.
3 To select an option, press SELECT.
4 Repeat steps 2-3 if any sub-option is available
under an option.
[Scan] (scan setting)
•[All
radio stations.
•[Strong
stations withstrong signals only.
[System]
•[Reset]: reset all the settings to factory default.
•[SW Version]: know the software versionof
the unit.
•[Language]: set system language (English
/ Deutsch / Itliano / Français / Norsk /

8EN
6 Other features
Set alarm time
Set alarm
Note
•You can only set the alarm in standby mode.
•Make sure that you have set the clock correctly.
1 In standby mode, press and hold AL1 or AL2
for more than 2 seconds to set alarm time.
2 Press HR to set hour and MIN to set minute,
then press AL1 or AL2
3 Press TUN to set alarm type (daily, once,
AL1 or
AL2
4 Press TUN to set an alarm source (FM,
AL1 or AL2 to
5 Press TUN to set the volume level, then
press AL1 or AL2
Tip
•The unit exits alarm setting mode when being idle for 15
seconds.
Activate/deactivate alarm timer
Press AL1 or AL2 repeatedly to activate or
deactivate the alarm timer.
If the alarm timer is activated, the alarm
indicator turns on.
If the alarm timer is deactivated, the alarm
indicator turns off.
The alarm repeats ringing for the next day.
To stop the alarm, press the coresponding
AL1 or AL2.
Snooze the alarm
When the alarm sounds, press SNOOZE.
The alarm snoozes and repeats ringing 9
minutes later.
Set sleep timer
This clock radio can switch to standby mode
automatically after a preset period.
•Press SLEEP repeatedly to select a period
The clock radio switches to standby mode
automatically afterthe preset period.
To deactivate the sleep timer:
•Press SLEEP repeatedly until [OFF
appears.
Adjust volume
While listening, pressVOL to adjust volume.
Adjust display brightness
Press BRIGHTNESS repeatedly to adjust the
display brightness.
•HIGH
•MED
•LOW

9
EN
8 T roubleshooting
Warning
•Never remove the casing of the product
To keep the warranty valid, never try to repair
the device yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips webpage (ww.philips.
com/support).When you contact Philips, make
sure that the device is nearby and the model
number and serial number are available.
No power
•Make sure that the AC power plug of the
unit is connected properly.
•Make sure that there is power at the AC outlet.
No sound
•Adjust the volume.
No response from the unit
•Disconnect and reconnect the AC power
plug, then turn on the unit again.
Poor radio reception
•Keep the clock radio away from other
electronic devices to avoid radio
interference.
•Fully extend and adjust the position of the
antenna.
Alarm does not work
•Set the clock/alarm correctly.
Clock/alarm setting erased
•Power has been interrupted or the power
plug has been disconnected.
•Reset the clock/alarm.
7 Product
information
Note
•Product information is subject to change without prior notice.
Rated Output Power 1W RMS
Tuner
Tuning Range FM: 87.5-108 MHz
DAB: 174.92-
239.20MHz
Tuning Grid 50 KHz
Sensitivity
- Mono, 26 dB S/N
Ratio
<22 dBf
Total Harmonic
Distortion
<3%
Signal to Noise Ratio >50 dBA
General information
AC Power (power
adaptor)
Brand: Philips;
Model:AS030-050-EM060
Input: 100-240V~
50/60 Hz; 0.15A
Output: 5V 0.6A
Operation Power
Consumption <3W
Standby Power
Consumption <1W
Dimensions
(W x H x D) 131x 54 x 131 mm
Weight
(Main unit) 267.3g

10 EN
never dispose of the product and batteries
with normal household waste. Correct disposal
of old products and batteries helps prevent
negative consequences for the environment and
human health.
Removing the disposal batteries
To remove the disposable batteries, see battery
install section.
9 Notice
device that are not expressly approved by
MMD Hong Kong Holding Limited may void
the user’s authority to operate the product.
Hereby, TPVision Europe B.V. declares that
this product isincompliance withthe essential
requirements and other relevant provisions
DeclarationofConformity on
www. philips.com/support.
This product complies with the radio
interference requirements of the European
Community.
This product is designed and manufactured with
high-quality materials and components, which
can be recycled and reused.
This symbol means the product must not be
discarded as household waste and should be
delivered to an appropriate collection facility for
recycling. Follow local rules and never dispose
of the product and rechargeable batteries with
normal household waste. Correct disposal
of old products and rechargeable batteries
helps prevent negative consequences for the
environment and human health.
This symbol means that the product contains
batteries covered by European Directive
2013/56/EU which cannot be disposed of with
normal household waste.
Inform yourself about the the local separate
collection system for electrical and electronic
products and batteries. Follow local rules and

2020 © Philips and the Philips Shield Emblem are registered trademarks
of Koninklijke Philips N.V. and are used under license.This product has been
manufactured by and is sold under the responsibility of MMD Hong Kong
Limited is the warrantor in relation to this product.
TAR3505_79_UM_V1.0