Philips SE1453B/05 User manual

7889 – Philips SE14x QSG – 04 – 08.12.06 7889 – Philips SE14x QSG – 04 – 08.12.06 7889 – Philips SE14x QSG – 04 – 08.12.06
Copyright © 2007 Koninklijke Philips Electronics N.V. All rights reserved.
Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners.
Specifications are subject to change without notice.
Document order number: 3111 285 38011 (GB)
Printed in P.R.C.
Troubleshooting
For more solutions, see the full FAQs section in the main guide.
No dialling tone
• Check the connections.
Unplug your phone then plug
back in the mains power.
• Batteries are empty –
charge the batteries for
at least 24 hours.
• You may be too far from
the base – move closer.
• Use the line cable provided.
Poor sound quality
• Move closer to the base.
• Move the base at least one
metre away from any electrical
appliances.
The icon is blinking
• Move closer to the base.
• Register the handset to
the base.
Caller Line Identification
does not work
Check your subscription with
your network operator.
No ring tone
If the icon is displayed, the
ringer is switched off. Increase
the ringer volume. For details,
see the main guide.
Need help?
See the user manual that came with your Philips SE140 or SE145.
Online help: www.philips.com/support
Welcome
Quick start guide
Connect
Install
Enjoy
1
2
3
Digital cordless phone SE140
Digital cordless phone with answering machine SE145
3Enjoy
Make a call
Enter the phone number and
press .
Answer a call
When the phone rings, press .
End a call
Press .
Adjust earpiece volume
During a call, press or .
Redial last number
Press then .
Change the ringer volume
and ringtone
• Press .
• Press or to adjust the
ringer volume level (0=off).
• Press 0–9 to select the ringtone.
A sample ringtone is played.
• Press to save the settings.
Add entry to phonebook
• Press then .
• Choose a position in the
phonebook by entering a
2-digit number between 01–20.
• Enter the phone number, then
press to confirm.
Dial from the phonebook
• Press , then scroll or
to the entry you want.
• Press to dial.
Set date and time
• Press twice.
• Enter the date (DD-MM) and
time (HH:MM).
• Press to confirm.
• Press to return to standby.
SE145 only
Switch the answering
machine off and on
Press at the base.
Listen to your messages
Press . Your new messages
are played.
Or
Press and hold to hear
all messages stored on your
machine.

7889 – Philips SE14x QSG – 04 – 08.12.06 7889 – Philips SE14x QSG – 04 – 08.12.06 7889 – Philips SE14x QSG – 04 – 08.12.06
1Connect
A Position the base
Place the base within reach of
the telephone line and power
sockets.
Connect the cables
Plug the line cord and power
cable into the sockets at the
back of the base.
Plug the other end of the cables
into the wall sockets.
Tip
Placing the base too close to
large metal objects or electrical
appliances can impair the range
and sound quality. Thick walls
may also impair transmission of
signals to and from the base.
B Plug into the sockets C
2Install
A Install the batteries
Insert the batteries and slide the
battery door into place.
Charge handset
Place the handset on the base to
charge the batteries. The battery
icon is displayed.
B
C Set up your phone
If the display shows the standby
screen, your phone is ready
to use.
Or
If the display shows
CODE: you
must select the country code
for your area. Please see page 15
in the main user guide for more
information.
• Scroll or to display the
correct code.
• Press to confirm.
The handset and base will reset
to load the correct settings and
the standby screen is displayed.
SE140 – your phone is ready
to use.
SE145 – your phone is ready
to use. The answering machine
is automatically set to On and
ready to record messages.
Warning
Leave the handset to charge for
at least 24 hours before first use.
Notes
* The line adaptor may not be attached to the line cord. If this is
the case, please connect the line cord to the line adaptor before
plugging it into the line socket.
• If you have purchased a multipack you will have additional handsets,
chargers, power adaptors and AAA rechargeable batteries.
Warning
Always use the cables and batteries supplied.
Warranty informationUser manual Quick start guide






What’s in the box?
2x AAA rechargeable
batteries
Line cord* Battery door
Power adaptorSE140/SE145 handset SE140 or SE145 base








 
 

7889 – Philips SE14x QSG – 04 – 08.12.06 7889 – Philips SE14x QSG – 04 – 08.12.06 7889 – Philips SE14x QSG – 04 – 08.12.06
1Connect
A Position the base
Place the base within reach of
the telephone line and power
sockets.
Connect the cables
Plug the line cord and power
cable into the sockets at the
back of the base.
Plug the other end of the cables
into the wall sockets.
Tip
Placing the base too close to
large metal objects or electrical
appliances can impair the range
and sound quality. Thick walls
may also impair transmission of
signals to and from the base.
B Plug into the sockets C
2Install
A Install the batteries
Insert the batteries and slide the
battery door into place.
Charge handset
Place the handset on the base to
charge the batteries. The battery
icon is displayed.
B
C Set up your phone
If the display shows the standby
screen, your phone is ready
to use.
Or
If the display shows
CODE: you
must select the country code
for your area. Please see page 15
in the main user guide for more
information.
• Scroll or to display the
correct code.
• Press to confirm.
The handset and base will reset
to load the correct settings and
the standby screen is displayed.
SE140 – your phone is ready
to use.
SE145 – your phone is ready
to use. The answering machine
is automatically set to On and
ready to record messages.
Warning
Leave the handset to charge for
at least 24 hours before first use.
Notes
* The line adaptor may not be attached to the line cord. If this is
the case, please connect the line cord to the line adaptor before
plugging it into the line socket.
• If you have purchased a multipack you will have additional handsets,
chargers, power adaptors and AAA rechargeable batteries.
Warning
Always use the cables and batteries supplied.
Warranty informationUser manual Quick start guide






What’s in the box?
2x AAA rechargeable
batteries
Line cord* Battery door
Power adaptorSE140/SE145 handset SE140 or SE145 base








 
 

7889 – Philips SE14x QSG – 04 – 08.12.06 7889 – Philips SE14x QSG – 04 – 08.12.06 7889 – Philips SE14x QSG – 04 – 08.12.06
1Connect
A Position the base
Place the base within reach of
the telephone line and power
sockets.
Connect the cables
Plug the line cord and power
cable into the sockets at the
back of the base.
Plug the other end of the cables
into the wall sockets.
Tip
Placing the base too close to
large metal objects or electrical
appliances can impair the range
and sound quality. Thick walls
may also impair transmission of
signals to and from the base.
B Plug into the sockets C
2Install
A Install the batteries
Insert the batteries and slide the
battery door into place.
Charge handset
Place the handset on the base to
charge the batteries. The battery
icon is displayed.
B
C Set up your phone
If the display shows the standby
screen, your phone is ready
to use.
Or
If the display shows
CODE: you
must select the country code
for your area. Please see page 15
in the main user guide for more
information.
• Scroll or to display the
correct code.
• Press to confirm.
The handset and base will reset
to load the correct settings and
the standby screen is displayed.
SE140 – your phone is ready
to use.
SE145 – your phone is ready
to use. The answering machine
is automatically set to On and
ready to record messages.
Warning
Leave the handset to charge for
at least 24 hours before first use.
Notes
* The line adaptor may not be attached to the line cord. If this is
the case, please connect the line cord to the line adaptor before
plugging it into the line socket.
• If you have purchased a multipack you will have additional handsets,
chargers, power adaptors and AAA rechargeable batteries.
Warning
Always use the cables and batteries supplied.
Warranty informationUser manual Quick start guide






What’s in the box?
2x AAA rechargeable
batteries
Line cord* Battery door
Power adaptorSE140/SE145 handset SE140 or SE145 base








 
 

7889 – Philips SE14x QSG – 04 – 08.12.06 7889 – Philips SE14x QSG – 04 – 08.12.06 7889 – Philips SE14x QSG – 04 – 08.12.06
Copyright © 2007 Koninklijke Philips Electronics N.V. All rights reserved.
Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners.
Specifications are subject to change without notice.
Document order number: 3111 285 38011 (GB)
Printed in P.R.C.
Troubleshooting
For more solutions, see the full FAQs section in the main guide.
No dialling tone
• Check the connections.
Unplug your phone then plug
back in the mains power.
• Batteries are empty –
charge the batteries for
at least 24 hours.
• You may be too far from
the base – move closer.
• Use the line cable provided.
Poor sound quality
• Move closer to the base.
• Move the base at least one
metre away from any electrical
appliances.
The icon is blinking
• Move closer to the base.
• Register the handset to
the base.
Caller Line Identification
does not work
Check your subscription with
your network operator.
No ring tone
If the icon is displayed, the
ringer is switched off. Increase
the ringer volume. For details,
see the main guide.
Need help?
See the user manual that came with your Philips SE140 or SE145.
Online help: www.philips.com/support
Welcome
Quick start guide
Connect
Install
Enjoy
1
2
3
Digital cordless phone SE140
Digital cordless phone with answering machine SE145
3Enjoy
Make a call
Enter the phone number and
press .
Answer a call
When the phone rings, press .
End a call
Press .
Adjust earpiece volume
During a call, press or .
Redial last number
Press then .
Change the ringer volume
and ringtone
• Press .
• Press or to adjust the
ringer volume level (0=off).
• Press 0–9 to select the ringtone.
A sample ringtone is played.
• Press to save the settings.
Add entry to phonebook
• Press then .
• Choose a position in the
phonebook by entering a
2-digit number between 01–20.
• Enter the phone number, then
press to confirm.
Dial from the phonebook
• Press , then scroll or
to the entry you want.
• Press to dial.
Set date and time
• Press twice.
• Enter the date (DD-MM) and
time (HH:MM).
• Press to confirm.
• Press to return to standby.
SE145 only
Switch the answering
machine off and on
Press at the base.
Listen to your messages
Press . Your new messages
are played.
Or
Press and hold to hear
all messages stored on your
machine.

7889 – Philips SE14x QSG – 04 – 08.12.06 7889 – Philips SE14x QSG – 04 – 08.12.06 7889 – Philips SE14x QSG – 04 – 08.12.06
Copyright © 2007 Koninklijke Philips Electronics N.V. All rights reserved.
Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners.
Specifications are subject to change without notice.
Document order number: 3111 285 38011 (GB)
Printed in P.R.C.
Troubleshooting
For more solutions, see the full FAQs section in the main guide.
No dialling tone
• Check the connections.
Unplug your phone then plug
back in the mains power.
• Batteries are empty –
charge the batteries for
at least 24 hours.
• You may be too far from
the base – move closer.
• Use the line cable provided.
Poor sound quality
• Move closer to the base.
• Move the base at least one
metre away from any electrical
appliances.
The icon is blinking
• Move closer to the base.
• Register the handset to
the base.
Caller Line Identification
does not work
Check your subscription with
your network operator.
No ring tone
If the icon is displayed, the
ringer is switched off. Increase
the ringer volume. For details,
see the main guide.
Need help?
See the user manual that came with your Philips SE140 or SE145.
Online help: www.philips.com/support
Welcome
Quick start guide
Connect
Install
Enjoy
1
2
3
Digital cordless phone SE140
Digital cordless phone with answering machine SE145
3Enjoy
Make a call
Enter the phone number and
press .
Answer a call
When the phone rings, press .
End a call
Press .
Adjust earpiece volume
During a call, press or .
Redial last number
Press then .
Change the ringer volume
and ringtone
• Press .
• Press or to adjust the
ringer volume level (0=off).
• Press 0–9 to select the ringtone.
A sample ringtone is played.
• Press to save the settings.
Add entry to phonebook
• Press then .
• Choose a position in the
phonebook by entering a
2-digit number between 01–20.
• Enter the phone number, then
press to confirm.
Dial from the phonebook
• Press , then scroll or
to the entry you want.
• Press to dial.
Set date and time
• Press twice.
• Enter the date (DD-MM) and
time (HH:MM).
• Press to confirm.
• Press to return to standby.
SE145 only
Switch the answering
machine off and on
Press at the base.
Listen to your messages
Press . Your new messages
are played.
Or
Press and hold to hear
all messages stored on your
machine.