Philips HC9450 User manual

4222.002.8558.3
HC9450
Register your product and get support at
www.philips.com/welcome
1
8
7
9
10
11
12
13
65
2
4
3
14
123 4
56 7
8 9 10
11 12 13
14 15
2 sec.
16
17
2 sec.
18 19
20 21
1
222
23 24 1
2
25
1
226 27 2
1
28
29 30
13/07/2015
保留备用

ENGLISH
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benet from the support that Philips
offers, register your product at www.philips.com/
welcome.
General description (Fig. 1)
1 Cutting unit
2 Memory button
3 Touch area
4 On/off button
5 Length setting lock
6 Charging light
7 Memory settings
8 Display
9 Trimming comb 1-7mm
10 Trimming comb 7-24mm
11 Trimming comb 24-42mm
12 Adapter
13 Small plug
14 Cleaning brush
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
-
Keep the appliance and the adapter dry. (Fig. 2)
Warning
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug,
as this causes a hazardous situation.
- This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
- Children should be supervised to ensure that
they do not play with the appliance.
Caution
- This appliance is not washable. Never rinse
the appliance in water or rinse it under the
tap (Fig. 2)
- Always check the appliance before you use it.
- Do not use the appliance, adapter or any other
part if it is damaged, as this may cause injury.
- Always replace a damaged adapter or part
with one of the original type.
- Only use this appliance for its intended
purpose as shown in the user manual.
- Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the appliance.
Electromagnetic elds (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic elds.
General
- The appliance is equipped with an automatic
voltage selector and is suitable for mains
voltages ranging from 100 to 240 volts.
- The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.
Charging
Charge the appliance fully before you use it for the
rst time or after a long period of disuse.
When it is charged for 1 hour, the appliance has
a cordless operating time of up to 120 minutes.
Note: After charging the appliance fully for the rst
time, you can also use the appliance directly from the
mains. Simply connect the appliance to the mains.
Charging indications
Battery low indication
- When the battery is almost empty, the
charging light starts to ash orange (Fig. 3).
Charging
- When the appliance is charging, the charging
light ashes blue.
Battery fully charged
- When the battery is fully charged, the charging
light lights up blue continuously (Fig. 4).
Note: After 30 minutes, the charging light goes out.
Charging the appliance
1 Make sure the appliance is switched off.
2 Insert the small plug into the
appliance (Fig. 5).
3 Put the adapter in the wall socket.
4 After charging, remove the adapter from the
wall socket and pull the small plug out of the
appliance.
Optimising the lifetime of the
rechargeable battery
When you have charged the appliance for the rst
time, we advise you to use it until the battery is
completely empty. Continue to use the appliance
until the motor almost stops operating during
a session.Then recharge the battery. Follow this
procedure at least twice a year.
Using the appliance
The hair length settings are indicated in millimetres.
The settings correspond to the remaining hair
length after trimming.
Be careful when you trim for the rst time.
Do not move the trimmer too fast. Make smooth
and gentle movements.
Tip: Start trimming at a high length setting and
reduce the length setting gradually until you have
reached the desired hair length.
Using the display
This appliance has a swipe and tap display that you
can use in three different ways:
1 Quickly swipe your thumb or a nger across
the touch area to scroll through the length
settings quickly (Fig. 6).
2 Slowly swipe your thumb or a nger across the
touch area to scroll through the length settings
slowly (Fig. 7).
3 Tap on the bottom or top part of the touch
area to go through the length settings one
by one.To scroll through the length settings
automatically in steps of 0.1mm, tap and hold
the bottom or top part of the touch area.
(Fig. 8)
Trimming with comb
There are 3 different combs:
- 1-7mm
- 7-24mm
- 24-42mm
1 Attach one of the combs to the appliance
(Fig. 9).
2 Swipe upwards or downwards to select the
desired length setting. (Fig. 10)
Note: When you trim for the rst time, start at the
highest length setting to familiarise yourself with the
appliance.
3 Switch on the appliance (Fig. 11).
4 To trim most effectively, move the trimmer
against the hair growth direction. Make sure
that the surface of the comb always stays in
contact with the skin (Fig. 12).
Trimming without comb
Use the trimmer without the trimming comb to
trim hair close to the skin (0.5mm) or to contour
the neckline and sideburns.
Be careful when you trim without comb because
the cutting unit removes every hair it touches.
1 Push the comb off the appliance (Fig. 13).
2 Switch on the appliance.
3 Touch the hair lightly with the trimmer.
Make well-controlled movements. (Fig. 14)
Features
Memory
The appliance has a memory which allows you to
save three frequently used length settings for each
comb. Each comb has different length ranges.
Saving a setting
1 Swipe upwards or downwards to select the
desired length setting (Fig. 15).
2 To enter the memory, press the ‘M’ button
for 2 seconds (Fig. 16).
,Number 1 starts to ash.
Note: If you want to save a length setting as number
2 or 3 in the memory, press the ‘M’ button again
(once for number 2 and twice for number 3) (Fig. 17).
3 To save a length setting as number 1, 2 or 3
of the memory, press the ‘M’ button for
2 seconds (Fig. 18).
,The display shows the word ‘SEt’ when
the length setting is correctly saved.
Memory setting number 1,2 or 3 lights up
continuously.
Selecting a memory setting
1 To enter the memory, press the ‘M’ button
once (Fig. 19).
,Number 1 starts to ash.
Note: To select number 2 or 3 in the memory, press
the ‘M’ button again (once for number 2 and twice
for number 3).
Length setting lock
This feature prevents accidental changing of the
length setting during trimming. Every time you
switch on the appliance, the length setting lock is
activated.You can only change the length setting if
you switch off the appliance.
1 Swipe upwards or downwards to select the
desired length setting (Fig. 15).
2 Switch on the appliance (Fig. 20).
,The lock symbol starts to ash. You cannot
change the length setting anymore.
Note: If you want to select a different length setting,
switch off the appliance. Swipe on the display to

Problem Possible cause Solution
The
length
setting I
set is not
stored
in the
memory.
You did
not save
the length
setting in the
memory in
the right way.
To save a length
setting in the
memory, press the
‘M’ button for
2 seconds until the
display shows ‘Set’.
The setting
you want
to select
from the
memory is
not available
for the
comb you
put on the
appliance.
The
message
‘CL’ is
shown
on the
display.
To much hair
has collected
between the
comb and
the cutting
unit.
Remove the comb
and cutting unit and
clean them with
the cleaning brush
supplied.
Also clean the top
edge of the handle
with the cleaning
brush supplied.
简体中文
简介
感谢您的惠顾，欢迎光临飞利浦！
为了您能充分享受飞利浦提供的支持，请在
www.philips.com/welcome 上注册您的产品。
基本说明 (图 1)
1 修剪部件
2 存储按钮
3 触摸区
4 开/关按钮
5 长度设定锁
6 充电指示灯
7 存储设定
8 显示屏
9 修剪梳 1-7 毫米
10 修剪梳 7-24 毫米
11 修剪梳 24-42 毫米
12 适配器
13 小插头
14 清洁刷
Problem Possible cause Solution
The setting
of the comb
has changed
during
trimming.
Check the setting of
the comb. If you push
the appliance too
hard onto the scalp,
you may accidentally
change the setting of
the comb.
The comb
is not
assembled
correctly.
Detach the comb
and reattach it.
The cutting
performance
decreases
when the
cutting unit
and the
comb are
dirty.
Clean the cutting
unit and the comb
(see chapter
‘Cleaning’).
The
appliance
does not
work
when I
switch it
on.
The
rechargeable
battery is
empty.
Charge the appliance
(see chapter
‘Charging’). Make
sure that the small
plug is inserted
into the appliance
properly and the
adapter is connected
to the wall socket
properly.
I cannot
select the
desired
length
setting.
The desired
length
setting is
not available
for the
comb you
put on the
appliance.
Make sure you use
the comb that offers
the desired length
setting.The length
settings are indicated
on the front of the
comb (1-7, 7-24 or
24-42).The appliance
automatically detects
the comb by its
length settings and
only allows you to
select the length
settings available for
that particular comb.
The
appliance is
switched on.
Switch off the
appliance.You can
only change the
length setting if the
appliance is switched
off.
Only remove the rechargeable battery if it is
completely empty.
1 Disconnect the appliance from the mains and
let the appliance operate until the motor
stops.
2 Press the release button (1) and remove the
cutting unit (2) (Fig. 26).
3 Insert the screwdriver between the motor
unit and the back panel of the appliance. Press
down the screwdriver as far as it will go
(Fig. 27)
4 Tilt the handle of the screwdriver downwards
(1) and separate the back panel from the
appliance (2). (Fig. 28)
5 Remove the side panels. Pull the bottom
part of the printed circuit board with the
rechargeable battery attached from the
appliance (Fig. 29).
6 Cut the wires to separate the rechargeable
battery from the appliance. (Fig. 30)
Do not connect the appliance to the mains again
after you have opened it.
Guarantee and support
If you need information or support, please visit
www.philips.com/support or read the separate
worldwide guarantee leaet.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the appliance.
If you are unable to solve the problem with the
information below, visit www.philips.com/
support for a list of frequently asked questions or
contact the Consumer Care centre in your country.
Problem Possible cause Solution
The
appliance
produces
an
uneven
cutting
result.
The comb
does not
touch the
skin when
you move
the appliance
through the
hair.
Make sure the comb
is always fully in
contact with the skin
when you move the
appliance through
the hair.
You only
move the
appliance
in one
direction.
Because not all hairs
grow in the same
direction, move the
appliance in different
directions (upwards,
downwards and
across).
select the desired length setting and switch on the
appliance again.
Cleaning
Never use scouring pads, abrasive cleaning agents
or aggressive liquids such as alcohol, petrol or
acetone to clean the appliance.
Never immerse the appliance in water or rinse it
under the tap.
1 Make sure the appliance is switched off and
disconnected from the mains.
2 Wipe the housing of the appliance with a dry
cloth.
3 Remove the comb and clean it with the
cleaning brush (Fig. 21).
4 Press the release button (1).The cutting unit
comes off the appliance (2). (Fig. 22)
5 Clean the cutting unit with the cleaning brush
(Fig. 23).
6 Clean the inside of the appliance with the
cleaning brush (Fig. 24).
7 Insert the lug of the cutting unit into the
guiding slot (1) and push the cutting unit back
onto the appliance (2) (Fig. 25).
Replacement
Only replace a worn or damaged cutting unit with
an original Philips cutting unit, available from
authorised Philips service centre.
1 Press the release button (1).The cutting unit
comes off the appliance (2). (Fig. 22)
2 Insert the lug of the new cutting unit into the
guiding slot (1) and push the cutting unit onto
the appliance (2) (Fig. 25).
Ordering accessories
To buy accessories or spare parts, visit
www.shop.philips.com/service or go to your
Philips dealer.You can also contact the Philips
Consumer Care Centre in your country (see the
worldwide guarantee leaet for contact details).
Recycling
Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an ofcial collection point for recycling. By doing
this, you help to preserve the environment.
Removing the rechargeable battery
Note: We strongly advise you to have a professional
remove the rechargeable battery.

注意： 如果您要将长度设定以编号 2 或 3 存
入存储器，请再次按“M”按钮（按一下对应
编号 2，按两下对应编号 3）。 (图 17)
3 要将长度设定以编号 1、2 或 3 存入存储
器，请按“M”按钮 2 秒钟。 (图 18)
,当长度设置正确保存时，显示屏将显
示“SEt”字样。存储器设置编号 1、
2 或 3 将持续亮起。
选择记忆的设定
1 如要进入存储器，请按一下“M”按钮。
(图 19)
,编号 1 将开始闪烁。
注意： 要选择存储器中的编号 2 或 3，请再
次按“M”按钮（按一下对应编号 2，按两下
对应编号 3）。
长度设定锁
该功能可防止修剪过程中意外更改长度设定。
每次打开产品时，便会启用长度设定锁。仅当
关闭产品后才能更改长度设定。
1 向上或向下滑动即可选择所需的长度设
定。 (图 15)
2 启动产品。 (图 20)
,锁定符号开始闪烁。您无法再更改长度设
定。
注意： 如果您要选择其他长度设定，请关闭
产品。在显示屏上滑动选择所需的长度设定，
然后重新打开产品。
清洁
切勿使用钢丝绒、研磨性清洁剂或腐蚀性液体
（例如酒精、汽油或丙酮）来清洁产品。
切勿将本产品浸入水中，也不要在自来水龙头
下冲洗。
1 确保产品电源关闭并已将电源插头拔出。
2 使用干布擦拭产品表面。
3 取下修剪梳并用清洁刷进行清洁。 (图 21)
4 按下释放钮 (1)。修剪部件将与产品 (2)
分离。 (图 22)
5 用清洁刷清洁修剪部件。 (图 23)
6 用清洁刷清洁产品内部。 (图 24)
7 将修剪部件的凸缘插入导向槽 (1) 内，
然后将修剪部件推回产品 (2)。 (图 25)
更换
如果修剪部件磨损或损坏，只能用原装飞利浦
修剪部件替换，原装部件可从授权的飞利浦服
务中心获得。
使用显示屏
本产品配有可滑动和轻击的显示屏，可以三种
不同方式使用：
1 在触摸区域快速滑动拇指或手指，快速滚
动查看长度设定。 (图 6)
2 在触摸区域缓慢滑动拇指或手指，缓慢滚
动查看长度设定。 (图 7)
3 轻击触摸区域的底部或顶部，逐一查看长
度设定。要自动滚动查看以 0.1 毫米为间
隔的长度设定，请轻击并按住触摸区域的
底部或顶部。 (图 8)
修剪（有修剪梳）
配有 3 种不同的修剪梳：
-1-7 毫米
-7-24 毫米
-24-42 毫米
1 将其中一个修剪梳安装到产品上。 (图 9)
2 向上或向下滑动即可选择所需的长度设定。
(图 10)
注意： 第一次修剪时，从最高的长度设定开
始修剪，以熟悉产品的使用方法。
3 启动产品。 (图 11)
4 为进行有效的修剪，应逆着须发生长的方
向移动修剪器。确保修剪梳表面与皮肤保
持接触。 (图 12)
修剪（无修剪梳）
使用不带修剪梳的修剪器以贴近皮肤的距离
（0.5 毫米）修剪须发或修整颈部和鬓角的轮
廓。
由于修剪部件会去除接触到的每一根须发，
因此在不带修剪梳修剪时要特别小心。
1 将修剪梳从产品中推出。 (图 13)
2 启动产品。
3 用修剪器轻轻触碰须发。必须控制好产品
的移动。 (图 14)
功能
内存
本产品具有存储器，您可以为每个修剪梳保存
三个常用的长度设置。每个修剪梳具有不同长
度范围。
保存设定
1 向上或向下滑动即可选择所需的长度设定。
(图 15)
2 要进入存储器，请按“M”按钮 2 秒钟。
(图 16)
,编号 1 将开始闪烁。
电磁场 (EMF)
本飞利浦产品符合所有有关暴露于电磁场的适
用标准和法规。
概述
-本产品配有一个自动电压选择器，
适合 100 至 240 伏范围内的电源电压。
-电源适配器可将 100-240 伏的电压转换为
24 伏以下的安全低电压。
充电
首次使用前或长时间不用之后，请为产品充
满电。
充电 1 小时后，产品可不接电源工作
120 分钟。
注意： 当首次为产品充满电后，您也可以直
接插电来使用本产品。只需将产品连接到电
源即可。
充电指示
电池电量低显示灯
-电池电量即将用尽时，充电指示灯会呈橙
色闪烁。 (图 3)
充电
-产品充电时，充电指示灯会呈蓝色闪烁。
电池已完全充满
-电池充满电后，充电指示灯会呈蓝色持续
亮起。 (图 4)
注意： 30 分钟后，充电指示灯会熄灭。
为产品充电
1 确保产品电源已关闭。
2 将小插头正确地插到产品上。 (图 5)
3 将电源适配器插入电源插座。
4 充电之后，从电源插座上拔下适配器，
并从产品上拔出小插头。
优化充电电池寿命
首次为产品充电后，建议您将产品一直使用到
电池耗尽为止。一直使用本产品，直到马达在
修剪过程中几乎停止运行，然后再为电池充
电。每年至少两次遵循此流程。
使用本产品
头发长度设定值以毫米为单位。设定值对应于
修剪后剩余头发的长度。
首次修剪时要特别小心。不要将修剪梳移得太
快，应确保动作轻柔流畅。
提示： 从较高的长度设定开始修剪，逐步减
小长度设定，直至达到所需的须发长度。
注意事项
使用本产品之前，请仔细阅读本
使用说明书，并妥善保管以备日
后参考。
危险
-让产品和电源适配器保持干燥。
(图 2)
-警告符号注释：禁止用在打开
的水龙头下进行清洗。
警告
-电源适配器内含有一个变压
器 。 切勿自行更换插头，
否则将导致严重后果。
-产品不打算由有肢体、感官或
精神能力缺陷或缺少使用经验
和知识的人（包括儿童）使
用，除非有负责他们安全的人
对他们进行与产品使用有关的
监督或指导。
-请照看好儿童，本产品不能用
于玩耍。
警告
-本产品不可水洗。切勿将本产
品浸入水中，也不要在水龙头
下冲洗 (图 2)
-警告符号注释：禁止用在打开
的水龙头下进行清洗。
-使用前，请务必检查产品。
-如果本产品、适配器或任何其
他部件损坏，请勿再使用，
否则可能对人体造成伤害。
-务必用原装型号更换损坏的适
配器或部件。
- 只能将本产品用于用户手册中
所示的原定用途。
-切勿使用压缩气体、钢丝绒、
研磨性清洁剂或腐蚀性液体
（例如汽油或丙酮）来清洁产
品。

问题 可能的
原因
解决方法
所设置的长
度设定未存
入存储器。
您未将
长度设
定正确
存入存
储器。
要将长度设定存
入存储器，请
按“M”按钮 2 秒
钟，直至显示屏
显示“Set”
（设置）。
您想从
存储器
中选择
的设定
不适用
于安装
在产品
上的修
剪梳。
显示屏将显
示“CL”信
息。
修剪梳
和修剪
部件间
积聚了
太多头
发。
卸下修剪梳和修
剪部件，并用随
附的清洁刷进行
清洁。另请用随
附的清洁刷对手
柄上方边缘进行
清洁。
本产品（同一型号）所配备的电源适配器有
2种规格，请以实物为准。
问题 可能的
原因
解决方法
理发器的修
剪效果不均
匀。
产品在
头发上
推动时
没有触
碰头
皮。
修剪梳在头发上
推动时，请确保
修剪梳可始终与
皮肤完全接触。
您只向
一个方
向移动
产品。
由于并非所有头
发都向一个方向
生长，请向不同
方向移动产品
（向上、向下以
及交叉）。
修剪过
程中修
剪梳的
设置有
所更
改。
检查修剪梳的设
置。如果您将产
品过于用力地按
在头皮上，您可
能会意外更改修
剪梳的设置。
修剪梳
组装不
正确。
卸下修剪梳，
重新安装。
如果修
剪部件
和修剪
梳不干
净，修
剪性能
会下
降。
清洁修剪部件和
修剪梳（见“清
洁”一章）。
启动产品
后，产品无
法工作。
充电电
池的电
量已耗
尽。
为产品充电
（见“充电”一
章）。确保小插
头已正确插入产
品，并且适配器
已正确连接至电
源插座。
我无法选择
所需的长度
设定。
所需的
长度设
定不适
用于安
装在产
品上的
修剪
梳。
确保使用能提供
所需长度设定的
修剪梳。长度设
定标在修剪梳的
正面（1-7、7-24
或 24-42）。产品
会自动检测修剪
梳的长度设定，
只允许选择特定
修剪梳提供的长
度设定。
产品已
打开。
关闭产品。仅当
关闭产品后才能
更改长度设定。
1 按下释放钮 (1)。修剪部件将与产品 (2)
分离。 (图 22)
2 将新修剪部件的凸缘插入导向槽 (1) 内，
然后将修剪部件推到产品上 (2)。 (图 25)
订购附件
要购买附件和备件，请访问
www.shop.philips.com/service 或 请联系飞利
浦经销商。您也可以联系您所在国家/地区的
飞利浦客户服务中心（联系详情，请参阅全球
保修卡）。
回收
弃置产品时，请不要将其与一般生活垃圾扔在
一起，应将其交给指定的回收中心，这样做有
利于环保。
卸下充电电池
注意： 强烈建议您让专业人员取下充电电池。
电池电量完全耗尽后方可取出充电电池。
1 断开产品电源并让产品继续运行，
直到马达停止。
2 按下释放钮 (1)，取下修剪部件 (2)。
(图 26)
3 将螺丝刀插在马达装置和产品后面板之
间。尽量向下按压螺丝刀 (图 27)
4 向下倾斜螺丝刀杆 (1)，然后使后面板与产
品 (2) 分离。 (图 28)
5 取下侧面板。从产品中拉出装有充电电池
的印刷电路板的底部。 (图 29)
6 剪断电线以将充电电池从产品上分开。
(图 30)
一旦打开产品，请勿再将其与电源相连。
保修和支持
如果您需要信息或支持，请访问
www.philips.com/support 或阅读单独的全球
保修卡。
故障种类和处理方法
本章归纳了使用本产品时最常见的一些问题。
如果您无法根据以下信息解决问题，
请访问 www.philips.com/support 查阅常见问
题列表，或联系您所在国家/地区的客户服务
中心。