Philips HS830/33 User manual

830
RECHARGEABLE
D
O
U
B
L
E
A
C
T
I
O
N
D
O
U
B
L
E
A
C
T
I
O
N
D
O
U
B
L
E
A
C
T
I
O
N
D
O
U
B
L
E
A
C
T
I
O
N
D
O
U
B
L
E
A
C
T
I
O
N
D
O
U
B
L
E
A
C
T
I
O
N
830
CHARGING

English page 3
Français page 12
Deutsch Seite 21
Nederlands pagina 31
Italiano pagina 40
Español página 49
Português página 59
2

3
1Do not allow the shaver to become wet.
2Do not leave the appliance in a position
where it can become damaged by direct
sunlight or other heat source.
• Please bear in mind that your skin may
need two to four weeks to become fully
accustomed to the Philishave shaving
system.
To protect the environment, this
rechargeable Philishave appliance is
equipped with a nickel-hydride battery
which contains less than 0.01% cadmium.
However we advise you to ensure that the
battery is separated from the normal
household refuse and disposed of at an
officially assigned place when discarding
your appliance in due course. Please refer to
section "Protecting the environment".
2
1
1
■■■ Important English

■■■ Switching on/off.
3The switch has a locking
button which prevents the
shaver from being switched
on accidentally.
Keeping the small button on
the switch pressed-in, slide
the switch
upwards/downwards.
■■■ Charging
•Ensure that the shaver is switched off.
•It is advisable to charge the shaver at
temperatures between 5 °C and 35 °C
(41°and 95 °F). This guarantees maximum life
from the rechargeable battery.
•If you keep the shaver in the case when
charging ensure that the lid is left open to
prevent overheating.
•A full charge requires approx. 8 hours.
• Regular cleaning of the shaver means that less
battery energy is consumed, so that more shaving
time becomes available.
4Set (if required) the voltage
switch in the appropriate
position:
230 for voltages ranging from
220-240 V AC.
115 for voltages ranging from
110-130 V AC.
4
CHARGING
3
4

5Insert the small plug firmly
into the shaver. Ensure that
the small plug is pushed
fully home. (Note the
indication mark.)
6Insert the mains plug into
the wall socket.
The green pilot light comes on.
7The green pilot light starts
flashing when the shaver is
fully charged.
• The shaver will not be
damaged by leaving it
connected to the mains supply
after it is fully charged.
However, it is not advisable to leave the shaver
connected permanently as this will shorten the life
of the rechargeable battery.
■■■ Cordless shaving
8Switch on.
830
CHARGING
5
6
7
830
CHARGING
CHARGING
8
5

9Move the shaving unit
quickly over the skin and
especially against the direction
of the hair growth, stretching
the skin with your free hand to
bring the hairs into an upright
position.
• Best results are obtained if the skin is dry.
Preferably shave before or some time after
washing.
• If required apply a pre-shave lotion. This can be
particularly helpful if the climate is warm and
humid.
■■■ Trimmer
The trimmer can be engaged whilst the motor is
running.
10 To engage the trimmer push
the slide upwards.
To disengage move the slide
downwards.
Brush the trimmer clean after
each use.
11 The trimmer has been
especially designed for
grooming sideburns,
moustache and beard.
The trimmer is not required for
long hairs in the neck area;
these hairs can easily be
shaved off with the shaving
unit. 6
9
10
11

12 Maintenance (every six
months)
Apply two drops of light
machine oil to the teeth of the
trimmer.
■■■ Cleaning
• Always ensure that the mains cord is
disconnected and the shaver is switched off
before carrying out maintenance or cleaning.
• Handle the shaving heads carefully to avoid
causing damage.
•Advice: Clean the shaver regularly.
13-16 Every week: shaving
head slots and hair chamber
- (Fig. 13) Use the short
bristled brush to clean the
shaving head slots.
- (Fig. 15/16) Remove hairs
from the chamber and
shaving unit using the long
bristled brush.
15
12
OIL
13
14
16
7

13-28 Every 3 months:
shaving head slots, hair
chamber and shaving unit
(guards and cutters)
(If your skin is of an oily type
or if you have been using a
pre-shave lotion: 1x per
month.)
- First clean the shaver head
slots and hair chamber as
previously described.
(See figs. 13-16.)
Then proceed with figs. 17-28
for cleaning the shaving unit.
(Fig. 19) Remove only one
shaving head (guard and
cutter) at a time for cleaning
to ensure that the cutters
and guards do not become
mixed.
Each cutter has been ground
together with the guard. If the
guards and cutters are mixed,
it may take some weeks before
optimal shaving performance
is restored.
1
17
2
18
19
20
8

- (Fig. 21) Clean the cutter by
brushing only in the
direction of the arrow using
the short bristled brush.
- (Fig. 23 & 28) If you have a
very dry skin, or if degreasing
liquid (e.g. alcohol) has been
used to clean the shaving
heads, lubricate the shaving
heads with one drop of light
machine oil.
As an alternative to using light
machine oil for lubrication you
may use the specially
formulated Philishave
cleaner/lubricant type 389
SHC/1 available from
Authorised Philips Service
Dealers.
9
22
23
OIL
24
21
25
25
1
26
2
27 28
OIL

■■■ Replacement shaving
heads
29 Use only Philishave
replacement heads type HP
1915 L when replacing worn or
damaged shaving heads.
■■■ Protecting the environment
30-35 When eventually
discarding your shaver please
remove the rechargeable
battery and dispose of it at an
officially assigned refuse site.
•Please note: You can also
take the appliance to a Philips
Service Centre. The staff will be happy to help
you.
- (Fig. 30) First ensure that the shaver is
disconnected from the mains supply.
-Before removing the battery should be
completely empty. Let the appliance run until the
motor stops.
- (Fig. 32) Use a small screwdriver (blade width
approx. 3 mm) or a Torx T-8 type screwdriver.
29
30 31
32
33
10