Philips Norelco 6000 Series User manual

BC
Tripleheader shaver
Series 6000
Tripleheader shaver

1
2
3
4
5
6 7
8
9
1110 12

empty page before TOC

English 6
Español 28

English
6English
Contents
IMPORTANT SAFETY INSTRUCTIONS______________________ 7
Introduction __________________________________________ 10
General description ____________________________________ 10
What do the icons on my product handle mean?___________ 11
How do I charge my product? ___________________________ 11
How do I use my product? ______________________________ 13
How do I clean my shaver? ______________________________ 17
Storage and travel _____________________________________ 21
How do I replace the shaving heads? _____________________ 22
Accessories ___________________________________________ 24
Assistance ____________________________________________ 24
Disposal ______________________________________________ 24
Full Two-Year Warranty ________________________________ 25
45-DAY MONEY-BACK GUARANTEE______________________ 26

7
English

IMPORTANT SAFETY
INSTRUCTIONS
When using an electric product, basic precautions should always be
followed, including the following:
Read all instructions before using this product.
DANGER
To reduce the risk of electric shock:
-Do not reach for a corded product that has fallen into water.
Unplug immediately from the power outlet.
-Keep the power cord dry.
-Do not place or store the product where it can fall or be pulled
into a tub or sink. Do not place or drop the product into water or
other liquid.
-This product does not work while it is connected to the power
outlet. Except when charging, always unplug this product from
the power outlet.
-Remove power cord from power outlet and product before
cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to
persons:

8English
-This product is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the product by a
person responsible for their safety. Children should be
supervised to ensure that they do not play with the product.
-Use this product only for its intended household use as described
in this manual. Misuse can lead do hazards or serious injuries. Do
not use attachments not recommended by Philips North America
LLC.
-Never operate this product if it has a damaged power cord, if it is
not working properly, after it has been dropped or damaged, or
after the product or power cord has been dropped into water.
For assistance call 1-800-243-3050.
-Keep the power cord away from heated surfaces.
-Never drop or insert any object into any opening.
-Do not use the power cord in or near a power outlet that
contains an electric air freshener to prevent damage to the
power cord.
-Do not use product outdoors or operate where aerosol (spray)
products are being used or where oxygen is being administered.
-Always check shaving heads (guards and cutters) before using
the product. Do not use the product if cutters or guards are
damaged, as injury may occur.
-Always attach power cord to product first, then to power outlet.
-Plug power cord directly into power outlet. Do not use an
extension cord.
-Unplug power cord before plugging in or unplugging the
product.
-The batteries used in this product may present a fire or chemical
burn hazard if mistreated. Do not disassemble, heat above
100°C (212°F) or incinerate.

9
English
-Only use original Philips accessories or consumables. Only use
detachable power cord HQ8505.
-Charge, use and store the product at a temperature between
5°C and 35°C.
-Keep product and batteries away from fire and do not expose
them to direct sunlight or high temperatures.
-If the product becomes abnormally hot or smelly, changes color
or if charging takes longer than usual, stop using and charging
the product and contact Philips.
-Do not place products and their batteries in microwave ovens or
on induction cookers.
-Do not open, modify, pierce, damage or dismantle the product
or battery to prevent batteries from heating up or releasing toxic
or hazardous substances. Do not short-circuit, overcharge or
reverse charge batteries.
-If batteries are damaged or leaking, avoid contact with the skin
or eyes. If this occurs, immediately rinse well with water and seek
medical care.
-When you handle batteries, make sure that your hands, the
product and the batteries are dry.
-To avoid accidental short-circuiting of batteries after removal, do
not let battery terminals come into contact with metal objects
(e.g. coins, hairpins, rings). Do not wrap batteries in aluminum
foil. Tape battery terminals or put batteries in a plastic bag
before you discard them.
IMPORTANT: The power plug contains a transformer. Do not cut
off the power plug to replace it with another plug as this will cause
a hazardous condition.
SAVE THESE INSTRUCTIONS

10 English
Introduction
Congratulations on your purchase and welcome
to Philips! To fully benefit from the support that
Philips offers, register your product at
www.philips.com/welcome or via the app.
General description
1 Shaving unit
2 Shaving unit release button
3 On/off button
4 Handle
5 Socket for small plug
6 Power plug
7 Small plug
8 Pouch
9 Cleaning brush
10 Length settings
11 Click-on beard styler attachment
12 Comb for beard styler attachment
The accessories supplied may vary for different
products. The box shows the accessories that
have been supplied with your product.
-This shaver is waterproof. It is suitable for use
in the bath or shower and for cleaning under
the tap. For safety reasons, the shaver can
therefore only be used without cord.

11
English
What do the icons on my product handle
mean?
Icon Behavior Meaning
Flashing when
you switch off the
product
Clean the shaver with warm water.
Flashing when
you press the
on/off button
The travel lock is activated (see 'Storage
and travel').
Lights up when
you pick up the
product
The number of bars lit up show the
remaining battery charge.
Bottom light
flashing orange
The battery is almost empty (see 'How
do I charge my product?').
Lights flashing in
sequence
The product is charging.
Lights up
continuously
The product is fully charged.
Flashing The product must be disconnected from
the power outlet before you can switch
it on.
How do I charge my product?
Charge the product before you use it for the first
time and when the bottom light of the battery
status indicator flashes orange, indicating that
the battery is almost empty.
Charging takes approx. 1 hour.

12 English
Quick Charge: After approx. 5 minutes of
charging, the battery contains enough energy for
one full shave.
When the product is fully charged it has a
cordless operating time of up to 60 minutes.
Note: You cannot use the product while it is
charging.
Charging with the power cord
1Make sure that the product is switched off.
2Insert the small plug into the product and put
the power plug in the power outlet.
-While the product is in quick charge mode,
the lights of the battery status indicator
light up one after the other. After
approximately 5 minutes, the bottom light
of the battery status indicator flashes. The
battery now contains enough energy for
one full shave.
-While the product charges, first the bottom
light of the battery status indicator flashes
and then lights up continuously. Next the
second light flashes and then lights up
continuously, and so on until the product is
fully charged.
-When the product is fully charged, all three
battery status indicator lights light up
continuously. After approx. 30 minutes, the
light goes out automatically.
3After charging, remove the power plug from
the power outlet and pull the small plug out
of the product.

13
English
'Unplug for use' symbol
The 'unplug for use' symbol flashes to remind you
to disconnect the power cord from the power
outlet and remove the small plug from the
product before you switch it on.
How do I use my product?
Always check the product and all accessories
before using. Do not use the product or any
accessory if it is damaged, as this may cause
injury. Always replace a damaged part with
one of the original type.
Note: This product is waterproof. It is suitable for
use in the bath or shower and for cleaning under
the tap with water. For safety reasons, this
product can only be used without cord.
Use this product for its intended household
use as described in this manual.
For hygienic reasons, the product should only
be used by one person.
Shaving
You can use this product either wet or dry, or
even in the shower. For a wet shave, apply some
water and shaving foam or gel to your skin and
rinse the shaving heads under the tap with warm
water before following the steps below.
1Switch on the product.

14 English
2Move the shaving heads over your skin in
circular movements to catch all hairs growing
in different directions. Make sure each shaving
head is fully in contact with the skin. Exert
gentle pressure for a close, comfortable shave.
Note: Do not press too hard, as this can cause
skin irritation.
Note: If you are shaving with gel or foam, rinse
the shaving unit regularly during your shave to
ensure that it continues to glide smoothly over
your skin.
3Use the narrow sides of the shaving unit to
shave in hard-to-reach areas such as along
your jawline and under your nose.
4Switch off and clean the product after each
use.
Note: Make sure you rinse all foam or shaving
gel off the product..
21-Day adaptation process
-21 Day Trial and Conversion Process. It is a fact
that your skin and beard need time to adjust
to a new grooming system.

15
English
-Use your new shaver exclusively for 3 weeks to
fully enjoy the closeness of a Philips Norelco
shave.
-At first you may not get as close a shave as you
expect, or your face may even become slightly
irritated. This is normal since your beard and
skin will need time to adjust. Invest 3 weeks
and you'll soon experience the full joy of your
new shaver.
-Stick with it! If you alternate shaving methods
during the adjustment period, it may make it
more difficult to adapt to the Philips Norelco
shaving system.
-If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
Cleaning reminder
When you switch off the product, the cleaning
reminder flashes to remind you to clean the
product.
-Clean the product and attachments after each
use (see 'How do I clean my shaver?') to
prevent clogging and damage.
-Clean the shaving heads thoroughly once a
month or when the product does not shave as
well as it used to.

16 English
Using the click-on attachments
Note: The accessories supplied may vary for
different products. The box shows the accessories
that have been supplied with your product.
Using the beard styler attachment with comb
You can use the beard styler attachment with the
comb attached to style your beard at one fixed
setting or at different length settings. You can
also use it to pre-trim any long hairs before
shaving for a more comfortable shave.
The hair length settings on the beard styler
attachment correspond to the remaining hair
length after cutting and range from 1 to 5mm.
1Twist the shaving head or other attachment to
remove it from the handle and press the beard
styler attachment onto the handle.
2Slide the comb straight into the guiding
grooves on both sides of the beard styler
attachment.
3Press the length selector and then push it to
the left or right to select the desired hair
length setting.
4Switch on the product.

17
English
5Move the product upwards while you exert
gentle pressure. Make sure the front of the
comb is in full contact with the skin.
6Switch off the product and clean the
attachment after each use (see 'How do I clean
my shaver?').
Using the beard styler attachment without
comb
You can use the beard styler attachment without
the comb to contour your beard, moustache,
sideburns or neckline to a length of 0.5mm.
1Pull the comb off the beard styler attachment.
Note: Grab the comb in the center to pull it off
the beard styler attachment. Do not pull at the
sides of the comb.
2Switch on the product.
3Hold the beard styler attachment
perpendicular to the skin and move the
appliance downwards while you exert gentle
pressure.
4Switch off the product and clean the
attachment after use.
How do I clean my shaver?
Clean the product and the attachments after
each use for optimal performance.
Cleaning the shaver under the tap
Clean the shaver after each use to prevent
clogging and damage.

18 English
Never dry the shaving unit with a towel or
tissue, as this may damage the shaving heads.
While rinsing the shaving unit, water may
drip out of the base of the shaver. This is a
normal occurrence.
1Switch on the shaver.
2Rinse the shaving unit under a warm tap.
3Switch off the shaver. Press the release button
to open the shaving unit.
4Rinse the hair chamber under a warm tap.
5Rinse the shaving head holder under a warm
tap.
6Carefully shake off excess water and let the
shaving head holder air-dry completely.

19
English
7Close the shaving unit.
Thorough cleaning
We advise you to clean the shaving heads
thoroughly once a month or when the shaver
does not shave as well as it used to.
1Make sure that the product is switched off and
disconnected from the power outlet.
2Press the release button on the shaving unit
and pull the shaving head holder off the
shaving unit.
3Rinse the hair chamber and shaving head
holder under the tap.
4Remove the shaving heads. For detailed
instructions, see 'How do I replace the shaving
heads?'.
Note: Do not clean more than one cutter and
guard at a time, since they are all matching
sets. If you accidentally put a cutter in the
wrong shaving guard, it may take several
weeks before optimal shaving performance is
restored.

20 English
5Clean the cutter and guard under the tap.
6Shake off excess water.
7Put the shaving heads back into the shaving
head holder. For detailed instructions, see
'How do I replace the shaving heads?'.
8Insert the hinge of the shaving head holder
into the slot in the top of the shaving unit and
close the shaving unit.
Cleaning the click-on attachments
Never dry the trimmer or beard styler
attachments with a towel or tissue, as this may
damage the trimming teeth.
The accessories supplied may vary for different
products. The box shows the accessories that
have been supplied with your product.
Clean the click-on attachments after each use for
optimal performance.
1Make sure that the product is switched off.
2Twist the attachment to remove it from the
handle.
3Clean the parts thoroughly with warm water.
4Carefully shake off excess water from the
beard styler, combs and nose/ear trimmer
attachments and let them air dry completely.