Philips PT848 User manual
Register your product and get support at
www.philips.com/welcome
Always here to help you
PT848
11
10
9
13
12
1
16
15
14
2
3
4
5
6
7
8
1
4
Introduction
Congratulations on your purchase and welcome to Philips!
www.philips.com/welcome
information about the wonderful features of this shaver as well as some
tips to make shaving easier and more enjoyable.
General description (Fig. 1)
1 Protection cap
2 Shaving unit
3 Shaving unit release button
4 On/off button
5 Charging light
6 Cap of SmartClean system
7 SmartClean system
8 Replacement symbol
9 Cleaning cartridge for SmartClean system
10 Cleaning symbol
11 On/off button
12 Ready symbol
13 Charge symbol
14 Adapter
15 Trimmer release slide
16 Trimmer
Important safety information
Read this important information carefully before you use the appliance and
its accessories and save it for future reference.The accessories supplied
may vary for different products.
Danger
- Keep the adapter dry.
Warning
- The adapter contains a transformer. Do not cut off the adapter to
- This appliance can be used by children aged from 8 years and above
lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and
appliance. Cleaning and user maintenance shall not be made by
children without supervision.
- Always unplug the shaver before you clean it under the tap.
- Always check the appliance before you use it. Do not use the appliance
with one of the original type.
ENGLISH
Caution
- Never immerse the cleaning system or the charging stand in water
and do not rinse it under the tap.
- Never immerse the shaver in water. Do not use the shaver in the
bath or in the shower.
- Never use water hotter than 80°C to rinse the shaver.
- Only use this appliance for its intended purpose as shown in the
user manual.
-
-
aggressive liquids such as petrol or acetone to clean the appliance.
-
cleaning system).
-
surface to prevent leakage.
-
that the cartridge compartment is closed before you use the cleaning
system to clean or charge the shaver.
-
- Water may drip from the socket at the bottom of the shaver when
you rinse it.This is normal and not dangerous because all electronics
are enclosed in a sealed power unit inside the shaver.
- This Philips appliance complies with all applicable standards and
General
- This shaver can be safely cleaned under the tap.
- The appliance is suitable for mains voltages ranging from 100 to 240 volts.
- The adapter transforms 100-240 volts to a safe low voltage of less than
24 volts.
-
Charging
It takes approx. 1 hour to fully charge the shaver.
A fully charged shaver provides up to 50 shaving minutes.
The shaving time may be less than 50 shaving minutes as a result of your
ENGLISH 5
Charge indications
Battery low
-
-
orange for a few seconds.
Quick charging
-
enough energy for a 5-minute shave.
Charging
-
Battery fully charged
-
green continuously.
Note:After approx. 30 minutes, the battery light goes out to save energy.
Charging with the adapter
1 Put the small plug in the shaver.
2 Put the adapter in the wall socket.
,The charging light shows the charging status of the shaver
(see section ‘Charge indications’ in this chapter).
Charging in the SmartClean system
1 Put the small plug in the SmartClean system.
2 Put the adapter in the wall socket.
3 Press the top cap to be able to place the shaver in the holder
(‘click’).
ENGLISH6
4 Hold the shaver upside down above the holder. Make sure the front
of the shaver points towards the SmartClean system.
5 Place the shaver in the holder (1), tilt the shaver backwards (2)
and press down the top cap to connect the shaver (‘click’) (3).
Note:The battery symbol lights up to indicate that the appliance is charging.
Using the shaver
Note:You can also use the shaver with cord by connecting it to the mains.
Shaving
1 Press the on/off button once to switch on the shaver.
2 Move the shaving heads over your skin. Make circular movements.
- Your skin may need 2 or 3 weeks to get accustomed to the
Philips shaving system.
3 Press the on/off button once to switch off the shaver.
4 Clean the shaver (see chapter ‘Cleaning and maintenance’).
Trimming
You can use the trimmer to groom your sideburns and moustache.
1 Push the trimmer slide downwards to open the trimmer.
2 Press the on/off button once to switch on the shaver.
,You can now start trimming
1
2
3
ENGLISH 7
3 After trimming, switch off the trimmer and clean it
(see chapter ‘Cleaning and maintenance’).Then close the trimmer.
Cleaning and maintenance
Remove the detachable cord from the handheld part before cleaning this
part in water.
Never use compressed air, scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the appliance.
- Clean the shaver after every shave for optimal shaving performance.
- Regular cleaning guarantees better shaving performance.
-
-
to prevent your hands from getting burnt.
Note:Water may leak from the socket at the bottom of the shaver when you
rinse it.This is normal and not dangerous because all electronics are enclosed
in a sealed power unit inside the shaver.
Cleaning the shaver in the SmartClean system
Preparing the SmartClean system for use
Do not tilt the SmartClean to prevent leakage.
Note: Hold the SmartClean while you prepare it for use.
1 Put the small plug in the back of the SmartClean system.
2 Put the adapter in the wall socket.
3 Press the button on the side of the SmartClean system (1)
and lift the top part of the SmartClean system (2).
1
2
ENGLISH8
4 Pull the seal off the cleaning cartridge.
5 Place the cleaning cartridge in the SmartClean system.
6 Push the top part of the SmartClean system back down (‘click’).
Using the SmartClean system
Always make sure to shake excess water off the shaver before you place
it in the SmartClean.
Note: If a lot of hairs have collected in the hair chamber, remove the hairs
before placing the shaver into the SmartClean. Open the shaving unit and
shake out excess hairs.
1 Press the top cap to be able to place the shaver in the holder
(‘click’).
2 Hold the shaver upside down above the holder. Make sure the front
of the shaver points towards the SmartClean system.
ENGLISH 9
3 Place the shaver in the holder (1), tilt the shaver backwards (2)
and press down the top cap to connect the shaver (‘click’) (3).
,
is charging.
4 Press the on/off button on the SmartClean system to start the
cleaning program.
,
Note:The rinsing phase takes approx. 10 minutes.
,When the cleaning program has been completed, the ready symbol
lights up continuously.
,The battery symbol lights up continuously to indicate that the shaver
is fully charged.
Note: Charging takes approx. 1 hour.
Note: If you press the on/off button of the SmartClean system during the
rinsing phase, the program aborts. In this case, the rinsing symbol stops
Note: If you remove the adapter from the wall socket during the rinsing phase,
the phase aborts.
Note: 30 minutes after the rinsing phase and charging have been completed,
the SmartClean switches off automatically.
5 To let the shaver dry, you can leave it in the SmartClean system
until your next shave.You can also remove the shaver from the
SmartClean system, shake off excess water, open the shaving unit and
let the shaver air dry.
Replacing the cartridge of the SmartClean System
-
1 Press the button on the side of the SmartClean system (1) and lift
the top part of the SmartClean system (2).
1
2
3
1
2
ENGLISH10
2 Take the empty cleaning cartridge from the SmartClean system and
3 Throw away the empty cleaning cartridge.
4 Unpack the new cleaning cartridge and pull the seal off the cartridge.
5 Place the new cleaning cartridge in the SmartClean system.
6 Push the top part of the SmartClean system back down (‘click’).
Cleaning the shaving unit under the tap
1 Switch off the shaver and disconnect it from the mains.
2 Press the release button to open the shaving unit.
3 Rinse the shaving unit and hair chamber under a hot tap for
30 seconds.
Be careful with hot water.Always check if the water is not too hot,
to prevent your hands from getting burnt.
- Rinse the hair chamber and the inside of the shaving unit.
ENGLISH 11
- Rinse the outside of the shaving unit.
4 Close the shaving unit and shake off excess water.
Be careful not to hit the shaving unit against anything while shaking
off excess water.
Never dry the shaving unit and the hair chamber with a towel or tissue,
as this may damage the shaving heads and the coupling spindles.
5 Open the shaving unit again and leave it open to let the shaver
dry completely.
Thorough cleaning
1 Switch off the shaver and disconnect it from the mains.
2 Press the release button to open the shaving unit.
3 Rinse the shaving unit and hair chamber under a hot tap for
30 seconds.
Be careful with hot water.Always check if the water is not too hot,
to prevent your hands from getting burnt.
- Rinse the hair chamber and the inside of the shaving unit.
- Rinse the outside of the shaving unit.
4 Pull the shaving unit off the shaver.
ENGLISH12
5 Turn the lock anticlockwise (A) and remove the retaining frame (B).
6 Remove and clean one shaving head at a time.
Each shaving head consists of a cutter and a guard.
Note: Do not clean more than one cutter and guard at a time, since they are
all matching sets. If you accidentally mix up the cutters and guards, it may take
several weeks before optimal shaving performance is restored.
7 Remove the cutter from the shaving guard and clean it under the tap.
Then clean the inside and outside of the shaving guard under the tap.
8 Put the shaving heads back into the shaving unit.
the recesses.
9 Put the retaining frame back into the shaving unit (A) and turn the
lock clockwise (B).
A
B
B
A
ENGLISH 13
10 Insert the lug of the shaving unit into the slot in the top of the shaver.
Then close the shaving unit.
Note: If the shaving unit does not close smoothly, check if you have inserted
the shaving heads properly and if the retaining frame is locked.
11 Shake off excess water.
Be careful not to hit the shaving unit against anything while shaking
off excess water.
Never dry the shaving unit and the hair chamber with a towel or tissue,
as this may damage the shaving heads and the coupling spindles.
12 Open the shaving unit again and leave it open to let the shaver
dry completely.
Cleaning the trimmer under the tap
Clean the trimmer every time you have used it.
1 Switch off the shaver and disconnect it from the mains.
2 Push the trimmer slide downwards to open the trimmer.
3 Clean the trimmer under the tap.
4 Close the trimmer (‘ click’).
Tip: For optimal trimming performance, lubricate the trimmer teeth with a
drop of sewing machine oil every six months.
ENGLISH14
Storage
- Put the protection cap on the shaver after use to prevent damage and
to avoid dirt accumulation in the shaving heads.
Replacement
heads every two years.
Replacement reminder
The shaving head symbol will light up to indicate that the shaving heads
need to be replaced. Replace damaged shaving heads right away.
1 The shaving head symbol lights up orange continuously.
2 Switch off the shaver. Disconnect the shaver from the mains and
remove it from the SmartClean System.
3 Press the release button to open the shaving unit.
4 Pull the shaving unit off the shaver.
5 Turn the lock anticlockwise (A) and remove the retaining frame (B).
6 Remove the shaving heads and place new ones in the shaving unit.
the recesses.
A
B
ENGLISH 15
7 Put the retaining frame back into the shaving unit (A) and turn
the lock clockwise (B).
8 Insert the lug of the new shaving unit into the slot in the top of
the shaver.Then close the shaving unit.
Note: If the shaving unit does not close smoothly, check if you have inserted
the shaving heads properly and if the retaining frame is locked.
9 Press and hold the on/off button for 5 seconds to reset the
replacement reminder on the shaver.The orange light goes out.
Ordering accessories
regularly and replace its shaving heads at the recommended time.
Shaving heads
- We advise you to replace your shaving heads every two years.
Cleaning
-
B
A
5 sec.
ENGLISH16
Recycling
- This symbol on a product means that the product is covered by
European Directive 2012/19/EU.
- This symbol means that the product contains a built-in rechargeable
battery covered by European Directive 2006/66/EC which cannot be
disposed of with normal household waste.We strongly advise you to
centre to have a professional remove the rechargeable battery.
- Inform yourself about the local separate collection system for electrical
and electronic products and rechargeable batteries. Follow local
rules and never dispose of the product and rechargeable batteries
with normal household waste. Correct disposal of old products and
rechargeable batteries helps prevent negative consequences for the
environment and human health.
Removing the rechargeable battery
Note:We strongly advise you to have a professional remove the
rechargeable battery.
Only remove the rechargeable battery when you discard the shaver.
Make sure the battery is completely empty when you remove it.
1 Disconnect the shaver from the mains.
2 Let the shaver run until it stops.
3 Undo the screws in the back of the shaver and in the hair chamber.
4 Remove the front panel and the back panel.
5 Bend the 6 hooks aside and take out the power unit.
Be careful, the hooks are sharp.
6 Remove the battery.
Be careful, the battery strips are sharp.
Do not connect the shaver to the mains again after you have removed
the rechargeable battery.
Guarantee and support
www.philips.com/
support
ENGLISH 17
Guarantee restrictions
the international guarantee because they are subject to wear.
Troubleshooting
This chapter summarises the most common problems you could
encounter with the appliance. If you are unable to solve the problem with
Problem Possible cause Solution
The shaver does
not shave as well as
it used to.
The shaving heads are damaged
or worn.
Replace the shaving heads
Long hairs obstruct the shaving
heads.
Clean the shaving heads one by one
You have not inserted the shaving
heads properly.
Make sure that the projections of the shaving
The shaver does
not work when I
press the on/off
button.
The rechargeable battery is
empty.
mains.
The temperature of the shaver is
does not work.
As soon as the temperature of the shaver
the shaver again.
Water leaks from
the shaver after
cleaning.
between the inner body and the
outer shell of the shaver.
During rinsing some water may collect
between the power unit and the housing.
the socket.The power unit is completely
watertight so water cannot reach the
electronic parts of the shaver.Your shaver
continues to be absolutely safe.
The SmartClean
system does not
work when I press
the on/off button.
The SmartClean system is not
connected to the mains.
Put the small plug in SmartClean system and
put the adapter in the wall socket.
The shaver is not
entirely clean after
I clean it in the
SmartClean system.
You have not placed the
shaver in the SmartClean
electrical connection between
the SmartClean system and the
shaver.
proper connection between the shaver and
the SmartClean system.
The cleaning cartridge needs
replacement.
ENGLISH18
Problem Possible cause Solution
The cleaning cartridge is empty.
to indicate you have to replace
the cleaning cartridge.
Place a new cleaning cartridge in the
SmartClean system
You have used another cleaning
cleaning cartridge.
Only use the Philips cleaning cartridge.
The drain of the cleaning
cartridge might be blocked.
Push the hairs down the drain with a
toothpick.
The shaver is not
fully charged after
I charge it in the
SmartClean system.
You have not placed the shaver in
the SmartClean system properly.
proper connection between the shaver and
the SmartClean system.
ENGLISH 19
20
Introduktion
Tillykke med dit køb og velkommen til Philips! For at få fuldt udbytte
www.philips.com/welcome.
oplysninger om shaverens unikke funktioner og tips til at gøre barbering
nemmere og sjovere.
1 Beskyttelseskappe
2 Skærhoved
3 Udløserknap til skærhoved
4 On/off-knap
5 Opladeindikator med lys
7 SmartClean-system
8 Udskiftningssymbol
9 Rengøringspatron til SmartClean-system
10 Rengøringssymbol
11 On/off-knap
12 Klar-symbol
13 Opladningssymbol
14 Adapter
15 Udløser til trimmer
16 Trimmer
Vigtige sikkerhedsoplysninger
Det medfølgende tilbehør kan variere for de forskellige produkter.
Fare
-
Advarsel
- Adapteren indeholder en transformer.Adapteren må ikke klippes af og
- Dette apparat kan bruges af børn fra 8 år og op og personer med
apparatet på en sikker måde og forstår de involverede risici. Børn må
ikke lege med apparatet. Rengøring og brugervedligeholdelse må ikke
foretages af børn uden opsyn.
-
-
altid erstatte en beskadiget del med en tilsvarende original type.
DANSK
Table of contents
Languages:
Other Philips Electric Shaver manuals
Philips
Philips Norelco 3000 Series Instruction Manual
Philips
Philips HQ4819 User manual
Philips
Philips Norelco 8260XL User manual
Philips
Philips OneBlade QP6541 User manual
Philips
Philips Essence 5000 Series User manual
Philips
Philips HQ 6890/A User manual
Philips
Philips T765/60 User manual
Philips
Philips PQ215 User manual
Philips
Philips QC5570/40 User manual
Philips
Philips BT7500 User manual
Philips
Philips Philishave HQ 487 User manual
Philips
Philips S9000 Series User manual
Philips
Philips PT923 User manual
Philips
Philips S7520/26 User manual
Philips
Philips HQ6425 User manual
Philips
Philips S5000 series User manual
Philips
Philips Essence 5000 Series User manual
Philips
Philips QP1324 User manual
Philips
Philips HQ444 User manual
Philips
Philips RQ1275CC User manual
