Philips PQ208 User manual

ENGLISH
Introduction
Congratulations on your purchase and
welcome to Philips! To fully benet from
the support that Philips offers, register your
product at www.philips.com/welcome.
General description (Fig. 1)
1 Protection cap
2 Shaving heads
3 Shaving unit
4 Retaining frame
5 Central spring of retaining frame
6 Release button
7 Hair chamber
8 On/off slide
9 Lid of battery compartment
10 Philips Cleaning Spray (HQ 110)
(Optional)
11 Cutter
12 Guard
13 Cleaning brush
Important
Read this user manual carefully before you
use the appliance and save it for future
reference.
Warning
- Keep the appliance dry.
- This symbol means: Forbidden to clean
under a running tap (Fig. 2).
- This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
- Children should be supervised to
ensure that they do not play with
the appliance.
Caution
- Use and store the appliance at a
temperature between 5°C and 35°C.
- Remove the batteries from the
appliance if you are not going to use it
for a month or more.
- Use Philips batteries to achieve optimal
shaving performance.
- Only use the cleaning brush supplied.
- Make sure the cleaning brush remains
clean.
Electromagnetic elds (EMF)
This Philips appliance complies with all
standards regarding electromagnetic elds
(EMF). If handled properly and according
to the instructions in this user manual, the
appliance is safe to use based on scientic
evidence available today.
Preparing for use
Inserting the batteries
The appliance operates on two R6 AA
1.5-volt alkaline batteries. Preferably insert
new Philips alkaline batteries to get optimal
shaving performance.
Make sure that your hands are dry when
you insert the batteries.
1 Remove the lid of the battery
compartment (Fig. 3)
2 Place two batteries in the battery
compartment (Fig. 4).
Note: Make sure the + and - indications on
the batteries match the indications in the
battery compartment.
Note:The shaver does not work if the
batteries have been placed incorrectly.
3 Put the lid of the battery
compartment back onto the appliance.
First place the top part of the lid (1)
and then press down the bottom part
until you hear a click (2) (Fig. 5).
How to avoid damage due to
battery leakage
- Do not expose the appliance to
temperatures higher than 35°C.
- Remove the batteries if you are not
going to use the appliance for a month
or more.
- Do not leave empty batteries in the
appliance.
Shaving time
Two new Philips alkaline batteries offer a
shaving time of 60 minutes.
Using the appliance
1 Remove the protection cap.
2 Press the on/off slide to unlock it
and push it upwards to switch on the
shaver (Fig. 6).
The on/off slide has an integrated switch
lock to prevent accidental switching on of
the shaver.
3 Move the shaving heads over your
skin. Make both straight and circular
movements (Fig. 7).
Note: Shave on a dry face only. Do not use the
shaver in combination with gel, foam or water.
Note: Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
4 Push the on/off slide downwards to
switch off the shaver.
PQ208, PQ206, PQ203, PQ202
Register your product and get support at
www.philips.com/welcome
4222.002.5313.2
2 3 4
5 6 7
8 9 10
11 12 13
14 15 16
17 18 19
20 21 22
23 24 25
1

5 Clean the shaver after every
shave, see chapter ‘Cleaning and
maintenance’.
6 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 8).
Cleaning and maintenance
Never use scouring pads, abrasive cleaning
agents or aggressive liquids such as petrol
or acetone to clean the appliance.
Clean the shaver after every shave to
guarantee better shaving performance.
For the best cleaning result, we advise you
to use Philips Cleaning Spray (HQ110).
Ask your Philips dealer for information.
Note: Philips Shaving Head Cleaning Spray
(HQ110) may not be available in all countries.
Contact the Customer Care Centre in your
country about the availability of this accessory.
After every shave: shaving unit
and hair chamber
1 Switch off the shaver.
2 Clean the top of the appliance with
the cleaning brush supplied (Fig. 9).
3 Press the release button (1) and pull
the shaving unit a straight up off the
shaver (2) (Fig. 10).
4 Clean the inside of the shaving unit
with the cleaning brush (Fig. 11).
5 Clean the hair chamber with the
cleaning brush (Fig. 12).
6 Put the shaving unit back onto the
shaver (Fig. 13).
Every two months: shaving heads
Note: Do not use cleaning agents or alcohol
to clean the shaving heads. Only use Philips
Cleaning Spray (HQ110).
1 Switch off the shaver.
2 Press the release button (1) and pull
the shaving unit straight up off the
shaver (2) (Fig. 10).
3 To remove the retaining frame,
push the sides of the central spring
towards each other (1).Then lift the
retaining frame out of the shaving unit
(2) (Fig. 14).
4 Slide the shaving heads out of
the retaining frame. Remove and
clean one shaving head at a time.
Each shaving head consists of a cutter
and a guard (Fig. 15).
Note: Do not clean more than one cutter and
guard at a time, since they are all matching
sets. If you accidentally mix up the cutters
and guards, it may take several weeks before
optimal shaving performance is restored.
5 Remove the guard from the
cutter (Fig. 16).
6 Clean it with the short-bristled side of
the cleaning brush. Brush carefully in
the direction of the arrows (Fig. 17).
7 Clean the guard with the long-bristled
side of the cleaning brush (Fig. 18)
8 Put the cutter back into the guard
after cleaning (Fig. 19).
9 Slide the shaving heads back into the
retaining frame. (Fig. 20)
10 Put the retaining frame back into the
shaving unit (‘click’) (Fig. 21).
11 Put the shaving unit back onto the
shaver (Fig. 13).
Storage
Keep the appliance dry.
Use and store the appliance at a
temperature between 5°C and 35°C.
1 Switch off the shaver.
2 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 22).
Replacement
Replace the shaving heads every two years
for optimal shaving results.
Replace damaged or worn shaving heads
with Philips shaving heads only (HQ4+ for
China or HQ56 for the rest of the world).
For instructions on how to remove the
shaving heads, see chapter ‘Cleaning and
maintenance’, section ‘Every two months:
shaving heads’.
Accessories
To retain the top performance of your
shaver, make sure you clean it regularly
and replace its shaving heads at the
recommended time.
Shaving heads
- We advise you to replace your shaving
heads every two years. Always replace
them with Philips shaving heads only
(HQ4+ for China or HQ56 for the
rest of the world) (Fig. 23).
Cleaning
- Use Philips Cleaning Spray (HQ110) to
clean the shaving heads thoroughly.
Environment
- Do not throw away the appliance
with the normal household waste at
the end of its life, but hand it in at an
ofcial collection point for recycling.
By doing this, you help to preserve the
environment (Fig. 24).
- Batteries contain substances that
may pollute the environment. Do
not throw away batteries with the
normal household waste, but dispose
of them at an ofcial collection point
for batteries. Always remove the
batteries before you discard and hand
in the appliance at an ofcial collection
point (Fig. 25).
Guarantee and service
If you need service or information or if
you have a problem, please visit the Philips
website at www.philips.com or contact
the Philips Consumer Care Centre in your
country. You nd its phone number in the
worldwide guarantee leaet. If there is no
Consumer Care Centre in your country, go
to your local Philips dealer.
Guarantee restrictions
The shaving heads (cutters and guards)
are not covered by the terms of the
international guarantee because they are
subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the
appliance. If you are unable to solve the
problem with the information below, contact
the Consumer Care Centre in your country.
Problem Possible
cause
Solution
The
shaver
does not
shave as
well as it
used to.
The shaving
heads are
dirty.You
have not
cleaned the
shaver well
enough or
you have
not cleaned
it for a long
time.
Clean the
shaver thor-
oughly before
you continue
shaving. See
chapter
‘Cleaning and
maintenance’.
Long hairs
obstruct
the shaving
heads.
Clean the
cutters and
guards with
the clean-
ing brush
supplied.
See chapter
‘Cleaning and
maintenance’,
section ‘Every
two months:
shaving heads’.
The shaving
heads are
damaged or
worn.
Replace the
shaving heads.
See chapter
‘Replacement’.
The
shaver
does not
work
when I
push the
on/off
slide up-
wards.
The bat-
teries are
placed
incorrectly.
Make sure
the + and -
indications on
the batteries
match the
indications in
the battery
compartment.
The bat-
teries are
empty.
Replace the
batteries.
See chapter
‘Preparing for
use’.
My
skin is
irritated
after
shaving.
Your skin
needs time
to get used
to the Philips
shaving
system.
Skin irritation
during the
rst 2-3
weeks of use
is possible.
After this
period, the
skin irritation
usually disap-
pears.
Problem Possible
cause
Solution
The
rotation
speed
of the
shaving
heads is
slower
than
usual.
Too much
dirt has
collected in
the shaving
heads.
Clean the
shaving heads.
See chapter
‘Cleaning and
maintenance’.
The bat-
teries are
empty
Replace the
batteries.
See chapter
‘Preparing for
use’.
The ap-
pliance
makes a
strange
noise.
Too much
dirt has
collected in
the shaving
heads.
Clean the
shaving heads.
After cleaning,
lubricate
the central
point on the
inside of the
guards with
Philips Clean-
ing Spray
(HQ110).
See chapter
‘Cleaning and
maintenance’.
The shaving
heads are
damaged or
worn.
Replace the
shaving heads.
See chapter
‘Replacement’.

是否有這項配件供應，請與您所在國家
的顧客服務中心聯繫。
每次刮鬍後：刮鬍刀組與鬍渣室
1 請先關閉電鬍刀電源。
2 使用隨附的清潔刷清潔產品上方。
(圖9)
3 按下釋放鈕(1)並將刮鬍刀頭組直
接向上拉起，自電鬍刀上取下(2)
。(圖10)
4 使用隨附的清潔刷清潔刮鬍刀頭組
內部。(圖11)
5 使用清潔刷清潔毛髮收集室。
(圖12)
6 將電鬍刀組裝回電鬍刀上。(圖13)
每兩個月：電鬍刀頭
注意：請勿使用清潔劑或酒精清潔電
鬍刀頭，務必使用飛利浦噴霧清潔劑
(HQ110)。
1 請先關閉電鬍刀電源。
2 按下釋放鈕(1)並將電鬍刀組從電
鬍刀(2)上拔開。(圖10)
3 要拆下固定架，請將中央彈簧的兩
側朝中間推壓(1)。然後提起固定架
從電鬍刀組取出(2)。(圖14)
4 將電鬍刀刀頭推出固定架外。一次
取下並清洗一個刀頭。每個電鬍刀
頭都是由刀片和刀網組成。(圖15)
注意：因為刀片及刀網是成對的一組，
請勿一次清潔一組以上。如果您不小心
將刀片及刀網混在一起，可能要花幾週
的時間才能恢復最理想的刮鬍效果。
5 取下刀具的刀網。(圖16)
6 請使用清潔刷的短毛側來進行清
潔。請依箭頭方向小心刷動。
(圖17)
 7 請使用清潔刷的長毛側來清潔刀
網(圖18)
 8 清潔後，將刀具放回刀網中。
(圖19)
 9 將電鬍刀刀頭推回固定架中。
(圖20)
10將固定架裝回電鬍刀組
(會聽見「喀噠」一聲)。(圖21)
11 將電鬍刀組裝回電鬍刀上。(圖13)
收納
請保持本產品乾燥。
請於 5°C 到 35°C 間使用並存放本
產品。
繁體中文
簡介
感謝您購買本產品並歡迎加入飛利浦！
請於 www.philips.com/welcome 註冊
您的產品，以善用飛利浦提供的支援。
一般說明 (圖 1)
1 保護蓋
2 電鬍刀刀頭
3 除毛刀頭組
4 固定架
5 固定架的中央彈簧
6 釋放鈕
7 毛髮收集室
8 開/關 (On/Off) 滑動開關
9 電池槽蓋
10 飛利浦噴霧清潔劑 (HQ110) (選購)
11 刀具
12 刀網
13 清潔刷
重要事項
使用本產品前，請先仔細閱讀本使用手
冊，並保留說明以供日後參考。
警示
-請保持本產品乾燥。
-此符號表示：禁止在水龍頭下清
洗。 (圖 2)
-基於安全考慮，在缺乏監督及適當
指示之下，本產品不適用於孩童及
任何身體、知覺、或心理功能障礙
者，或缺乏使用經驗及知識者。
-請勿讓孩童使用本產品或將本產品
當成玩具。
警告
-請於 5°C 到 35°C 間使用並存放
本產品。
-如果將有一個月以上的時間不使用
本產品，請將電池取出。
-請使用飛利浦電池以達到最佳刮鬍
效果。
-只能使用隨附的清潔刷。
-清潔刷請務必保持乾淨。
電磁波 (EMF)
本飛利浦產品符合電磁波
(Electromagnetic fields，EMF) 所有相
關標準。只要使用方式正確並依照本
使用手冊之說明進行操作，根據現有
的科學研究資料，使用本產品並無安
全顧慮。
使用前準備
裝入電池
本產品使用兩顆 R6 AA 1.5 伏特鹼性電
池；建議使用飛利浦鹼性電池以達到最
佳刮鬍效果。
裝入電池時請保持雙手乾燥。
1 打開電池盒的蓋子。(圖3)
2 將兩顆電池裝入電池盒內。(圖4)
注意：請確認電池上的+/-正負極位置
與電池盒內的標示位置相符。
注意：如果電池裝入的方向不正確，電
鬍刀將無法運作。
3 將電池盒蓋壓回機體，然後向上推
關緊。先放好蓋子的頂部(1)，接著
按下底部直到聽見「喀噠」一聲(2)
。(圖5)
為避免電池漏電造成損壞：
-請勿讓產品暴露於超過攝氏 35°C
的高溫。
-如果將有一個月以上的時間不使用
本產品，請將電池取出。
-請勿將電力耗盡的電池留置在此產
品中。
刮鬍時間
兩顆新的飛利浦鹼性電池可以讓電鬍刀
連續使用約 60 分鐘。
使用本產品
1 卸下保護蓋。
2 按On/Off開關來解鎖，然後將之向
上推即可開啟電鬍刀電源。(圖6)
On/Off 開關配備內建開關鎖，可以防止
電鬍刀電源被意外開啟。
3 將電鬍刀頭在皮膚上移動，請同時
用直線及畫圓的方式來移動。
(圖7)
注意：僅可乾刮。使用電鬍刀時，請勿
搭配凝露、泡沫或水。
注意：您的皮膚可能需要2到3週的
時間才能完全適應飛利浦電鬍刀系統。
4 將On/Off開關往下推，即可關閉電
鬍刀電源。
5 每次刮鬍後，請清潔本電鬍刀，請
參閱「清潔與保養」單元。
6 使用後請為電鬍刀蓋上保護蓋以防
損壞，並避免污垢累積在刀頭中。
(圖8)
清潔與維護
絕對不可使用鋼絲絨、磨蝕性的清潔劑
或侵蝕性的液體(例如汽油或丙酮)清潔
本產品。
每次刮鬍後清潔電鬍刀，以維持較佳的
刮鬍效能。
為達最好的清潔效果，建議您使用飛利
浦噴霧清潔劑 (HQ110)。請向您的飛利
浦經銷商洽詢相關資訊。
注意：飛利浦電鬍刀刀頭噴霧清潔劑
(HQ110)並非所有國家都有供應。關於
問題 可能原因 解決方法
電鬍刀
不像平
常一樣
運作。
電鬍刀刀頭
不潔。電鬍
刀清潔不夠
徹底或是太
久沒有清
潔。
在您繼續刮
鬍之前，請
徹底清潔電
鬍刀。請參
閱「清潔與
維護」單
元。
長鬍鬚卡住
電鬍刀刀
頭。
請使用隨附
的毛刷清潔
刀具及刀
網。請參閱
「清潔與維
護」單元之
「每兩個
月：電鬍刀
刀頭」小
節。
電鬍刀刀頭
毀壞或磨
損。
更換電鬍刀
刀頭。請參
閱「更換」
單元。
將 on/
off 開
關往上
推，但
電鬍刀
不動。
電池安裝的
位置不正
確。
請確認電池
上的 +/- 正
負極位置與
電池盒內的
標示位置相
符。
電池電量
耗盡
更換電池
(請參閱
「使用前
準備」單
元)。
刮鬍之
後，皮
膚感到
刺痛。
您的皮膚需
要一些時間
才能適應飛
利浦電鬍刀
系統。
開始使用
的第 2 到 3
週，皮膚可
能會有過敏
現象。過了
這段時間，
皮膚過敏的
症狀通常會
消失。
刀頭的
旋轉速
度比平
常緩
慢。
過多污垢累
積在刀頭
中。
請清潔電鬍
刀刀頭。請
參閱「清潔
與維護」
單元。
電池電量
耗盡
更換電池
(請參閱
「使用前
準備」單
元)。
1 請先關閉電鬍刀電源。
2 使用後請為電鬍刀蓋上保護蓋以防
損壞，並避免污垢累積在刀頭中。
(圖22)
更換
每隔兩年更換一次電鬍刀頭，以確保維
持最佳的刮鬍效果。
損壞或用舊的刀頭限以飛利浦電鬍刀
刀頭替換 (中國為 HQ4+，其他國家為
HQ56)。
有關如何取下電鬍刀頭的說明，請參閱
「清潔與維護」單元之「每兩個月：
電鬍刀頭」章節。
配件
若要維持電鬍刀的最佳效能，請務必定
期清潔電鬍刀，並於建議的時間更換電
鬍刀刀頭。
電鬍刀刀頭
-建議您每兩年即更換電鬍刀刀頭。
限以飛利浦電鬍刀刀頭替換 (中國
為 HQ4+，其他國家為 HQ56)。
(圖 23)
清潔
-使用飛利浦噴霧清潔劑 (HQ110)
徹底清潔電鬍刀頭。
環境保護
-本產品使用壽命結束時請勿與一般
家庭廢棄物一併丟棄。請將該產品
放置於政府指定的回收站，此舉能
為環保盡一份心力。 (圖 24)
-電池內含可能會污染環境的物質，
請勿與一般家庭廢棄物一併丟棄，
應送至政府指定的電池回收點進行
回收。若要丟棄本產品，也請將電
池取出，再將產品送至政府指定的
回收點。 (圖 25)
保固與服務
如需相關服務或資訊，或是有任何
問題，請瀏覽飛利浦網站，網址
為：www.philips.com，或聯絡您所在
國家/地區的飛利浦客戶服務中心，電話
號碼可參閱全球保證書。若您的所在國
家/地區沒有客戶服務中心，請洽詢當地
的飛利浦經銷商。
保固限制
電鬍刀刀頭 (刀具和刀網) 由於其耗損
性，因此不在全球保固範圍內。
故障排除
本說明概述您使用本產品時最常遇到的
問題。如果您無法利用以下資訊解決您
遇到的問題，請聯絡您所在國家/地區的
客戶服務中心。

問題 可能原因 解決方法
產品發
出奇怪
的噪
音。
過多污垢累
積在刀頭
中。
請清潔電鬍
刀刀頭。清
潔後，請使
用飛利浦噴
霧清潔劑
(HQ110) 潤
滑刀網內側
的中心點。
請參閱「清
潔與維護」
單元。
電鬍刀刀頭
毀壞或磨
損。
更換電鬍刀
刀頭。請參
閱「更換」
單元。