Philips 9000 series User manual

Tripleheader shaver
S9031
Tripleheader shaver

1
2
3
4
5
6
7
8
9
10
11
12
13

empty page before TOC

English 6
Español 30

English
Contents
IMPORTANT SAFETY INSTRUCTIONS______________________ 6
General description (Fig.1)__________________________________ 8
Introduction_________________________________________________ 9
The display__________________________________________________ 9
Charging_____________________________________________________ 13
Using the product___________________________________________ 14
Shaving______________________________________________________ 16
Cleaning and maintenance_________________________________ 20
Storage______________________________________________________ 25
Replacement________________________________________________ 25
Accessories__________________________________________________ 26
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric product, basic precautions should
always be followed, including the following:
Read all instructions before using this product.
DANGER
To reduce the risk of electric shock:
-Do not reach for a corded product that has fallen into water.
Unplug immediately from the power outlet.
-Keep the power cord dry.
6English

-Do not place or store the product where it can fall or be
pulled into a tub or sink. Do not place or drop the product
into water or other liquid.
-This product does not work while it is connected to the
power outlet. Except when charging, always unplug this
product from the power outlet.
-Remove power cord from power outlet and product before
cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to
persons:
-Close supervision is required when this product is used by,
on, or near children, or persons with limited physical, sensory,
or mental capabilities or invalids.
-Use this product only for its intended household use as
described in this manual. Do not use attachments not
recommended by Philips North America LLC.
-Never operate this product if it has a damaged power cord, if
it is not working properly, after it has been dropped or
damaged, or after the product or power cord has been
dropped into water. For assistance call 1-800-243-3050.
-Keep the power cord away from heated surfaces.
-Never drop or insert any object into any opening.
-Do not use the power cord in or near a power outlet that
contains an electric air freshener to prevent damage to the
power cord.
-Do not use product outdoors or operate where aerosol
(spray) products are being used or where oxygen is being
administered.
7
English

-Always check shaving heads (caps and cutters) before using
the product. Do not use the product if cutters or caps are
damaged, as injury may occur.
-Always attach power cord to product first, then to power
outlet.
-Plug power cord directly into power outlet. Do not use an
extension cord.
-Unplug power cord before plugging in or unplugging the
product.
-Only use the power cord and other accessories supplied with
the product.
-Do not attempt to open the product to remove or replace the
built-in rechargeable battery.
-The batteries used in this product may present a fire or
chemical burn hazard if mistreated. Do not disassemble, heat
above 100°C (212°F) or incinerate.
IMPORTANT: The power plug contains a transformer. Do not
cut off the power plug to replace it with another plug as this will
cause a hazardous condition.
SAVE THESE
INSTRUCTIONS
General description (Fig.1)
1 Comb for beard styler attachment
2 Click-on beard styler attachment
3 Click-on shaving unit
4 On/off button
5 Cleaning reminder
6 Travel lock symbol
7 Battery charge indicator
8 Replacement reminder
8English

9 Notification symbol
10 Socket for small plug
11 Supply unit
12 Small plug
13 Travel case
Introduction
Congratulations on your purchase and
welcome to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.philips.com/register.
The display
Note: Before you use the shaver for the first
time, remove the protective foil from the
display.
Charging
Quick charge: When you connect the shaver to
the wall socket, the lights of the battery charge
indicator light up one after another repeatedly.
When the shaver contains enough energy for
one shave, the bottom light of the battery
charge indicator starts to flash slowly.
While the shaver continues to charge, first the
bottom light of the battery charge indicator
flashes and then lights up continuously. Then
the second light flashes and lights up
9
English

continuously, and so on until the shaver is fully
charged.
Battery fully charged
When the battery is fully charged, all lights of
the battery charge indicator light up white
continuously.
Note: This product can only be used without a
cord. When you press the on/off button during
or after charging, you hear a sound to indicate
that the shaver is still connected to the wall
socket.
Note: When the battery is full, the display turns
off automatically after 30 minutes.
Battery low
When the battery is almost empty, the bottom
light of the battery charge indicator flashes
orange and you hear a sound. At this point
there is enough energy left for one shave.
Remaining battery charge
The remaining battery charge is shown by the
lights of the battery charge indicator that light
up continuously.
10 English

Cleaning reminder
Clean the shaver after every use for optimal
performance. When you turn off the product,
the cleaning reminder flashes to remind you to
clean the shaver.
Travel lock
When you are going to travel, you can lock the
shaver to prevent it from accidentally turning
on.
Activating the travel lock
3 sec.
1Press the on/off button for 3 seconds to
use the travel lock mode.
When the travel lock is activated, the shaver
produces a sound and the travel lock
symbol flashes.
If you try to turn on the shaver while the
travel lock is active, the travel lock symbol
flashes.
Deactivating the travel lock
1Press the on/off button for 3 seconds.
While you deactivate the travel lock, the
travel lock symbol lights up briefly and the
shaver produces a short sound.The shaver
turns on and is now ready for use again.
11
English

Note: You can also deactivate the travel lock
by connecting the product to the wall socket.
Replacement reminder
For maximum shaving performance, we advise
you to replace the shaving heads every 12
months.
The shaver is equipped with a replacement
reminder, which reminds you to replace the
shaving heads. The shaving unit symbol lights
up white continuously, the arrows flash white,
and the shaver beeps to indicate that you
have to replace the shaving heads.
Note: After replacing the shaving heads, you
can reset the replacement reminder by
pressing the on/off button for 7 seconds. If you
do not reset the replacement reminder, the
shaver resets automatically after 9 shaves.
Notification symbol
Overheating
If the product overheats during charging, the
notification symbol flashes red. When this
happens, the shaver stops charging
automatically. Charging continues once the
temperature of the shaver has decreased to
the normal level after approx. 10 minutes.
12 English

Blocked shaving heads
If the shaving heads are blocked, the
notification symbol continuously lights up red.
The replacement reminder and the cleaning
reminder alternately flash white and the
shaver beeps. In this case, the motor cannot
run because the shaving heads are dirty or
damaged. If the shaving heads are dirty, you
have to clean them. If the shaving heads are
damaged, you have to replace them.
Charging
-Charging or using the product at
temperatures below 40°F (4.5°C) or higher
than 95°F (35°C) adversely affects the
lifespan of the battery.
-Do not charge the shaver in a pouch or
travel case.
-The power plug transforms 100-240V AC to
less than 24V DC.
Charge the shaver before you use it for the first
time and when the display indicates that the
battery is almost empty. The battery charge is
indicated by the lights of the battery charge
indicator on the display.
Charging takes approx. 1 hour. A fully charged
shaver has a shaving timeof up to 50 minutes.
Note: You cannot use the shaver while it is
charging.
1Make sure the product is turned off.
13
English

1
2
2Put the small plug in the shaver and
connect the power plug to any 100V to
240V AC outlet. Use only the power cord
provided.
When you connect the shaver to the wall
socket, you hear a sound.
3After charging, remove the power plug from
the wall outlet and pull the small plug out of
the product.
Using the product
Always check the product and all
accessories before using. Do not use the
product or any accessory if it is damaged, as
this may cause injury. Always replace a
damaged part with one of the original type.
This symbol indicates that the shaver can be
used in the bath or shower.
-Use this shaver for its intended household
use as described in this manual.
-For hygienic reasons, the shaver should
only be used by one person.
-Trimming is easier when the skin and hair
are dry.
This product can only be used without a
cord.
This shaver is suitable for use in the bath or
shower. For safety reasons, it is therefore
not possible to use the shaver while it is
connected to the power outlet for charging.
14 English

21-Day adaptation process
-21 Day Trial and Conversion Process. It is a
fact that your skin and beard need time to
adjust to a new grooming system.
-Use your new shaver exclusively for 3 weeks
to fully enjoy the closeness of a Philips
Norelco shave.
-At first you may not get as close a shave as
you expect, or your face may even become
slightly irritated. This is normal since your
beard and skin will need time to adjust.
Invest 3 weeks and you'll soon experience
the full joy of your new shaver.
-Stick with it! If you alternate shaving
methods during the adjustment period, it
may make it more difficult to adapt to the
Philips Norelco shaving system.
-If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
Turning the shaver on and off
-To turn on the shaver, press the on/off
button once.
The display lights up for a few seconds.
-To turn off the shaver, press the on/off
button once.
The display lights up for a few seconds and
shows the remaining battery charge.
15
English

Shaving
-For the best results on skin comfort, pre-
trim your beard if you have not shaved for 3
days or longer.
Dry shaving
1Turn on the shaver.
The display lights up for a few seconds.
2Move the shaver in circular movements over
your skin to catch hair growing in all
directions.
3Stretch your skin with your free hand so
blades can lift and cut hair. Gently press
shaver to skin so the floating heads can
follow the contours of your face.
Note: Do not press too hard as too much
pressure can pinch the skin.
4After shaving, turn off the product.
5Clean the shaver.
Wet shaving
For a more refreshing shave, you can also use
this shaver on a wet face with shaving foam or
gel.
To shave with shaving foam or shaving gel,
follow the steps below:
1Apply some water to your skin.
16 English

2Apply shaving foam or shaving gel to your
skin.
3Turn on the shaver.
4Rinse the shaving unit under the tap to
ensure that the shaving unit glides smoothly
over your skin.
5Move the shaving heads over your skin in
circular movements to catch all hairs
growing in different directions. Make sure
each shaving head is fully in contact with
the skin. Exert gentle pressure for a close,
comfortable shave.
Note: Rinse the shaving unit regularly to
ensure that it continues to glide smoothly
over your skin.
6Turn off and clean the shaver after each
use.
7Dry your face.
Note: Rinse all foam or shaving gel off the
shaver after each use.
Using the click-on attachments
Removing or attaching click-on attachments
1Make sure the shaver is turned off.
17
English

2Pull the attachment straight off the shaver.
Note: Do not twist the attachment while you
pull it off the shaver.
3Insert the lug of the attachment into the slot
in the top of the shaver. Then press down
the attachment to attach it to the shaver
(‘click’).
Using the beard styler attachment with
comb
You can use the beard styler attachment with
the comb attached to style your beard at one
fixed setting or at different length settings. You
can also use it to pre-trim any long hairs
before shaving for a more comfortable shave.
The length settings on the beard styler
attachment correspond to the remaining hair
length after cutting and range from 1 to 5mm
(3/64 - 3/16in).
1Attach the attachment to the shaver ('click').
2Slide the comb straight into the guiding
grooves on both sides of the beard styler
attachment (‘click’).
1
2
3Press the length selector and then push it
to the left or right to select the desired hair
length setting.
18 English

4Turn on the shaver.
5Move the shaver upwards while you exert
gentle pressure. Make sure the front of the
comb is in full contact with the skin.
6Clean the attachment after use (see
'Cleaning and maintenance').
Using the beard styler attachment without
comb
You can use the beard styler attachment
without the comb to contour your beard,
moustache, sideburns or neckline at a length
of 0.5mm (1/32in).
Note: The beard styler is only intended for
trimming facial hair. Do not use it on areas
below the neck.
1Pull the comb off the beard styler
attachment.
Note: Grab the comb in the center to pull it
off the beard styler attachment. Do not pull
at the sides of the comb.
2Turn on the shaver.
3Hold the beard styler attachment
perpendicular to the skin and move the
shaver downwards while you exert gentle
pressure.
4Clean the attachment after use (see
'Cleaning and maintenance').
19
English

Cleaning and maintenance
Note: The accessories supplied may vary for
different products. The box shows the
accessories that have been supplied with your
product.
Regular cleaning guarantees better
shaving results.
Never clean, remove or replace the shaving
unit while the shaver is turned on.
Do not touch shaving heads with hard
objects as this may dent or damage the
precision-made slotted shaving head.
Do not use abrasives, scourers or
aggressive liquids such as gasoline or
acetone to clean the shaver.
Cleaning the shaver
Clean the shaver after every use for optimal
performance.
Always check if the water is too hot, to prevent
burning your hands.
While rinsing shaving heads, water may drip
out of the base of shaver. This is a normal
occurrence. Internal electric parts are in a
waterproof compartment so the shaver will be
protected against water damage.
1Turn on the shaver.
20 English