Philips S7780 Manual

Question?
有疑问?
Contact Philips
请联系飞利浦
S7780
S7720
S7530

1

S7780, S7720, S7530
ENGLISH 6
简体中文 32

6
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benet from the support that Philips
offers, register your product at www.philips.com/
welcome.
Please read this user manual, as it contains information
about the features of this shaver as well as some tips
to make shaving easier and more enjoyable.
General description (Fig. 1)
1 Protection cap for cleansing brush attachment
2 Click-on cleansing brush attachment
3 Comb for beard styler attachment
(specic types only)
4 Click-on beard styler attachment
(specic types only)
5 Click-on trimmer attachment (specic types only)
6 Click-on shaving unit
7 Handle
8 Socket for small plug
9 Battery charge indicator
10 ’Unplug for use’ symbol
11 Travel lock symbol
12 Replacement reminder
13 Cleaning reminder
14 Cleaning cartridge for SmartClean system
15 SmartClean system (specic types only)
16 Cap of SmartClean system
17 On/off button
18 Charge symbol
19 Ready symbol
20 Replacement symbol
21 Cleaning symbol
22 Adapter
23 Small plug
24 Pouch
ENGLISH

Important
Read this important information carefully before you
use the shaver and the SmartClean system (specic
types only). Save this leaet for future reference.
Danger
- Keep the adapter dry.
Warning
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug,
as this causes a hazardous situation.
- This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
- Children should be supervised to ensure that they
do not play with the appliance.
- Always unplug the shaver before you clean it
under the tap.
Caution
- Never immerse the SmartClean system in water
nor rinse it under the tap.
- Never use water hotter than 80°C to rinse
the shaver.
- Do not use the shaver, SmartClean system,
adapter or any other part if it is damaged, as
this may cause injury. Always replace a damaged
adapter or part with one of the original type.
- Only use the SmartClean system with the original
SmartClean cleaning cartridge.
- Always place the SmartClean system on a stable,
level and horizontal surface to prevent leakage.
ENGLISH 7

- When the SmartClean system is ready for use,
do not move it to prevent leakage of cleaning uid.
- Always make sure that the cartridge compartment
is closed before you use the SmartClean system
to clean or charge the shaver.
- The SmartClean system thoroughly cleans but
does not disinfect your shaver, therefore do not
share the shaver with others.
- Never use compressed air, scouring pads, abrasive
cleaning agents or aggressive liquids such as petrol
or acetone to clean the appliance.
- Water may leak from the socket at the bottom
of the shaver when you rinse it.This is normal
and not dangerous because all electronics are
enclosed in a sealed power unit inside the shaver.
Compliance with standards
- This shaver is waterproof and complies with
the internationally approved safety regulations.
It is suitable for use in the bath or shower and
for cleaning under the tap. For safety reasons,
the shaver can therefore only be used cordlessly.
- The shaver and the SmartClean system comply
with all applicable standards and regulations
regarding exposure to electromagnetic elds.
General
- The adapter is equipped with an automatic
voltage selector and is suitable for mains voltages
ranging from 100 to 240 volts.
- The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.
ENGLISH8

The display
Charging
Note:This appliance can only be used cordlessly.
- Charging takes approx. 1 hour.
- Quick charge:When the appliance is connected
to the mains, the lights of the battery charge
indicator light up one after the other continuously.
When the shaver contains enough energy for
one shave, the bottom light of the battery charge
indicator starts to ash slowly.
- If you leave the appliance connected to the
mains, the charging process continues.To indicate
that the appliance is charging, rst the bottom
light ashes white and then lights up white
continuously. Then the second light ashes and
then lights up continuously, and so on until the
shaver is fully charged.
Battery fully charged
Note:This appliance can only be used cordlessly.
Note:When the battery is full, the display switches
off automatically after 30 minutes.When you press
the on/off button during charging, the ‘unplug for use’
symbol ashes white to remind you that you have to
disconnect the appliance from the mains.
- When the battery is fully charged, all lights of
the battery charge indicator light up white
continuously.
ENGLISH 9

Battery low
- When the battery is almost empty, the bottom
light ashes orange.
Remaining battery capacity
- The remaining battery capacity is indicated by
the lights of the battery charge indicator that light
up continuously.
Cleaning reminder
For optimal shaving performance, we advise you to
clean the shaver after every use.
- When you switch off the shaver, the cleaning
reminder ashes to remind you to clean the
shaver.
Travel lock
You can lock the shaver when you are going to
travel.The travel lock prevents the shaver from being
switched on by accident.
Activating the travel lock
1 Press the on/off button for 3 seconds to enter
the travel lock mode.
,While you activate the travel lock, the travel lock
symbol lights up white continuously.When the
travel lock is activated, the travel lock symbol
ashes.
ENGLISH10

Deactivating the travel lock
1 Press the on/off button for 3 seconds.
,The travel lock symbol ashes and then lights up
continuously.
The shaver is now ready for use again.
Replacing shaving heads
For maximum shaving performance, we advise you
to replace the shaving heads every two years.
- The appliance is equipped with a replacement
reminder which reminds you to replace the
shaving heads.The replacement reminder lights up
white continuously.
Note: After replacing the shaving heads, you need to
reset the shaver by pressing the on/off button for
7 seconds.
’Unplug for use’ reminder
- The appliance is equipped with an ‘unplug for use’
reminder. The ‘unplug for use’ symbol ashes white
to remind you that you have to disconnect the
appliance from the mains.
ENGLISH 11

Charging
Charging takes approx. 1 hour.
A fully charged shaver has a shaving time of up to
50 minutes.
Note:This appliance can only be used cordlessly.
Charge the shaver before you use it for the rst
time and when the display indicates that the battery
is almost empty .
Charging with the adapter
1 Make sure that the appliance is switched off.
2 Insert the small plug into the appliance (1)
and put the adapter in the wall socket (2).
Charging in the SmartClean system
(specic types only)
1 Put the small plug in the SmartClean system.
2 Put the adapter in the wall socket.
3 Press the top cap to be able to place the
shaver in the holder (‘click’).
4 Hold the shaver upside down above the holder.
Make sure the front of the shaver points
towards the SmartClean system.
ENGLISH12

5 Place the shaver in the holder (1),
tilt the shaver backwards (2) and press down
the top cap to connect the shaver (‘click’).
Note: The battery symbol ashes slowly to indicate
the appliance is charging.
Using the shaver
Shaving
Skin adaptation period
Your rst shaves may not bring you the result you
expect and your skin may even become slightly
irritated.This is normal.Your skin and beard need
time to adapt to any new shaving system.
We advise you to shave regularly (at least 3 times
a week) with this shaver for a period of 3 weeks to
allow your skin to adapt to the new shaver.
Note:This appliance can only be used cordlessly.
1 Press the on/off button once to switch on
the shaver.
,The display lights up for a few seconds.
2 Move the shaving heads over your skin in
circular movements.
Note: Do not make straight movements.
3 Press the on/off button once to switch off
the shaver.
,The display lights up for a few seconds to show
the remaining battery charge percentage.
ENGLISH 13

Wet shaving
You can also use this shaver on a wet face with
shaving foam or shaving gel.
To shave with shaving foam or shaving gel,
follow the steps below:
1 Apply some water to your skin.
2 Apply shaving foam or shaving gel to your skin.
3 Rinse the shaving unit under the tap to ensure
that the shaving unit glides smoothly over
your skin.
4 Press the on/off button once to switch on
the shaver.
5 Move the shaving heads over your skin in
circular movements.
Note: Rinse the shaver under the tap regularly to ensure
that it continues to glide smoothly over your skin.
6 Dry your face and thoroughly clean the shaver
after use (see chapter ‘Cleaning and maintenance’).
Note: Make sure you rinse all foam or shaving gel off
the shaver.
ENGLISH14

Using the click-on attachments
Using the beard styler attachment
(specic types only)
1 Make sure that the appliance is switched off.
2 Pull the shaving unit straight off the appliance.
Note: Do not twist the shaving unit while you pull it off
the appliance.
3 Insert the lug of the beard styler attachment
into the slot in the top of the appliance.
Then press down the beard styler attachment
to attach it to the appliance (‘click’).
Using the beard styler attachment with comb
You can use the beard styler attachment with the
comb attached to style your beard at one xed
setting, but also at different length settings.
The hair length settings on the beard styler
attachment correspond to the remaining hair
length after cutting and range from 1 to 5mm.
1 Slide the comb straight into the guiding
grooves on both sides of the beard styler
attachment (‘click’).
2 Press the length selector and then push it
to the left or right to select the desired hair
length setting.
3 Press the on/off button once to switch on
the appliance.
4 You can now start styling your beard.
ENGLISH 15

Using the beard styler attachment
without comb
You can use the beard styler attachment without
the comb to contour your beard, moustache,
sideburns or neckline.
1 Pull the comb off the beard styler attachment.
Note: Grab the comb in the centre to pull it off the
beard styler attachment. Do not pull at the sides of
the comb.
2 Press the on/off button once to switch on
the appliance.
3 You can now start contouring your beard,
moustache, sideburns or neckline.
Using the trimmer attachment
(specic types only)
You can use the trimmer attachment to groom
your sideburns and moustache.
1 Make sure that the appliance is switched off.
2 Pull the shaving unit straight off the appliance.
Note: Do not twist the shaving unit while you pull it off
the appliance.
3 Insert the lug of the trimmer attachment into
the slot in the top of the appliance.Then press
down the trimmer attachment to attach it to
the appliance (‘click’).
4 Press the on/off button once to switch on
the appliance.
5 You can now start trimming.
ENGLISH16

Using the cleansing brush attachment
Use the rotating cleansing brush attachment with
your daily cleansing cream.The cleansing brush
attachment removes oil and dirt, contributing to
a healthy and oil-free skin.
1 Pull the shaving unit straight off the appliance.
Do not twist the shaving unit while you pull it off
the appliance.
2 Insert the lug of the cleansing brush attachment
into the slot in the top of the appliance.
Then press down the cleansing brush
attachment to attach it to the appliance (‘click’).
3 Moisten the cleansing brush attachment and
your face with warm water and cleansing cream.
Tip: Use the cleansing brush attachment before shaving
for easier shaving and a more hygienic shaving result.
4 Press the on/off button to switch on
the appliance.
5 Start cleaning the T-zone with the cleansing
brush attachment.
Note: Make circular motions, but not more than
3 times in one spot.
6 Start cleansing the rest of your face.
Tip:Treat your face with the cleansing brush
attachment for about one minute.
Caution: Do not clean the sensitive area around
your eyes.
ENGLISH 17

Cleaning and maintenance
Cleaning the shaver in the SmartClean
system (specic types only)
Do not tilt the SmartClean to prevent leakage.
Note: Hold the SmartClean while you prepare it for use.
Preparing the SmartClean system for use
1 Put the small plug in the back of the
SmartClean system.
2 Put the adapter in the wall socket.
3 Press the button on the side of the SmartClean
system (1) and lift the top part of the
SmartClean system (2).
4 Pull the seal off the cleaning cartridge.
5 Place the cleaning cartridge in the SmartClean
system.
6 Push the top part of the SmartClean system
back down (‘click’).
ENGLISH18

Using the SmartClean system
Always make sure to shake excess water off
the shaver before you place it in the SmartClean.
1 Press the top cap to be able to place the
shaver in the holder (‘click’).
2 Hold the shaver upside down above the holder.
Make sure the front of the shaver points
towards the SmartClean system.
3 Place the shaver in the holder (1), tilt the
shaver backwards (2) and press down the top
cap to connect the shaver (‘click’).
,The battery symbol starts to ash,
which indicates that the shaver is charging.
4 Press the on/off button on the SmartClean
system to start the cleaning program.
,The rinsing symbol starts to ash slowly.
Note:The cleaning program takes approx. 10 minutes.
ENGLISH 19

,When the cleaning program has been completed,
the ready symbol lights up continuously.
,The battery symbol lights up continuously to
indicate that the shaver is fully charged.This
takes approx. 1 hour.
Note: If you press the on/off button of the SmartClean
system during the cleaning program, the program
aborts. In this case, the cleaning symbol stops ashing.
Note: If you remove the adapter from the wall socket
during the cleaning program, the program aborts.
Note: 30 minutes after the cleaning program and
charging have been completed, the SmartClean
switches off automatically.
Replacing the cartridge of the SmartClean
System
- Replace the cleaning cartridge when the
replacement reminder ashes orange or when
you are no longer satised with the result.
1 Press the button on the side of the SmartClean
system (1) and lift the top part of the
SmartClean system (2).
2 Take the empty cleaning cartridge from the
SmartClean system and pour any remaining
cleaning uid out of the Cleaning cartridge.
You can simply pour the cleaning uid down the sink.
3 Throw away the empty cleaning cartridge.
4 Unpack the new cleaning cartridge and pull
the seal off the cartridge.
5 Place the new cleaning cartridge in the
SmartClean system.
ENGLISH20