Philips S7880 User manual

S7880

1
2
3
4
5
6
7
8
10
9
11
13
12
14

empty page before TOC

English 6
简体中文 27

English
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that
Philips offers, register your product at
www.philips.com/welcome.
General description
1 Protection cap for cleansing brush attachment
2 Click-on cleansing brush attachment
3 Click-on precision trimmer attachment
4 Click-on shaving unit
5 Handle
6 Socket for small plug
7 Battery charge indicator with 3 lights
8 Unplug for use symbol
9 Travel lock symbol
10 Replacement reminder
11 Cleaning reminder
12 Small plug
13 Supply unit
14 Pouch
Important safety information
Read this important information carefully before
you use the appliance and save it for future
reference.
Danger
- Keep the supply unit dry.
- This symbol means: Forbidden to clean under a
running tap.
6English

Warning
- To charge the battery, only use the detachable
supply unit (HQ8505) provided with the
appliance.
- The supply unit contains a transformer. Do not
cut off the supply unit to replace it with another
plug, as this causes a hazardous situation.
- This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning and
user maintenance shall not be made by
children without supervision.
- Always unplug the appliance before you clean it
under the tap.
- Always check the appliance before you use it.
Do not use the appliance if it is damaged, as
this may cause injury. Always replace a
damaged part with one of the original type.
- This appliance contains batteries that are non-
replaceable.
- Do not open the appliance to replace the
rechargeable battery.
Caution
- Never use water hotter than 60°C to rinse the
appliance.
- Only use this appliance for its intended purpose
as shown in the user manual.
- For hygienic reasons, the appliance should only
be used by one person.
7
English

- Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the
appliance.
- Water may drip from the socket at the bottom
of the appliance when you rinse it. This is
normal and not dangerous because all
electronics are enclosed in a sealed power unit
inside the appliance.
- Do not use the supply unit in or near wall
sockets that contain an electric air freshener to
prevent irreparable damage to the supply unit.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.
General
- This symbol means: Suitable to be used in the
shower. It is allowed to use this appliance close
to a bathtub, shower or other containers filled
with water.
- This appliance is waterproof. It is suitable for
use in the bath or shower and for cleaning
under the tap. For safety reasons, the appliance
can therefore only be used without cord.
- The supply unit is suitable for mains voltages
ranging from 100 to 240 volts.
- The supply unit transforms 100-240 volts to a
safe low voltage of less than 24 volts.
The display
Battery charge indicator
Note: If you press the on/off button during
charging, the 'unplug for use' symbol flashes white
to remind you that you have to disconnect the
appliance from the wall socket.
8English

Quick charge: When the battery is empty and you
connect the appliance to the wall socket, the lights
of the battery charge indicator light up one after
the other repeatedly. When the appliance contains
enough energy for one shave, the bottom light of
the battery charge indicator starts flashing slowly.
While the appliance continues to charge, first the
bottom light of the battery charge indicator flashes
and then lights up continuously. Then the second
light flashes and then lights up continuously, and
so on until the appliance is fully charged.
Battery fully charged
Note: When the battery is full, the display switches
off automatically after 30 minutes.
Note: This appliance can only be used without
cord.
When the battery is fully charged, all lights of the
the battery charge indicator light up white
continuously.
When you press the on/off button while the shaver
is still connected to the wall socket, the 'unplug for
use' symbol lights up to remind you to disconnect
the shaver from the wall socket before you can
switch it on.
Note: When the battery is full, the display switches
off automatically after 30 minutes.
Battery low
When the battery is almost empty, the bottom light
of the battery charge indicator flashes orange.
9
English

Remaining battery charge
The remaining battery charge is shown by the
lights of the battery charge indicator that light up
continuously.
’Unplug for use’ reminder
The ‘unplug for use’ symbol flashes to remind you
that you have to disconnect the appliance from
the wall socket before you can switch it on.
Cleaning reminder
Clean the shaver after every use for optimal
performance (see 'Cleaning and maintenance').
When you switch off the appliance, the cleaning
reminder flashes to remind you to clean the
appliance.
Travel lock
You can lock the appliance when you are going to
travel. The travel lock prevents the appliance from
being switched on by accident (see 'Activating the
travel lock').
Activating the travel lock
3 sec.
1Press the on/off button for 3 seconds to use
the travel lock mode.
10 English

While you activate the travel lock, the travel lock
symbol lights up continuously. When the travel
lock is activated, the travel lock symbol flashes.
Deactivating the travel lock
1Press the on/off button for 3 seconds.
While you deactivate the travel lock, the travel
lock symbol lights up briefly and the shaver
produces a short sound. The appliance switches
on and is now ready for use again.
Replacement reminder
For maximum shaving performance, we advise you
to replace the shaving heads every two years. The
appliance is equipped with a replacement
reminder which reminds you to replace the
shaving heads. The shaving unit symbol lights up
and the arrows flash to indicate that you have to
replace the shaving heads.
Note: After replacing the shaving heads, you can
reset the replacement reminder by pressing the
on/off button for 7 seconds. If you do not reset the
replacement reminder, the shaver resets
automatically after 9 shaves.
Charging
Charge the shaver before you use it for the first
time and when the display indicates that the
battery is almost empty.
Charging takes approx. 1 hour. A fully charged
shaver has a shaving timeof up to 50 minutes.
Note: You cannot use the appliance while it is
charging.
11
English

Charging with the supply unit
1Make sure the appliance is switched off.
1
2
2Put the small plug in the appliance and put the
supply unit in the wall socket.
3After charging, remove the supply unit from the
wall socket and pull the small plug out of the
appliance.
Using the appliance
Note: This appliance can only be used without
cord.
Switching the appliance on and off
1To switch on the appliance, press the on/off
button once.
2To switch off the appliance, press the on/off
button once.
Battery charge indicator with 3 lights: The display
lights up for a few seconds to show the remaining
battery status.
Shaving
Skin adaptation period
Your first shaves may not bring you the result you
expect and your skin may even become slightly
irritated. This is normal. Your skin and beard need
time to adapt to any new shaving system. To allow
your skin to adapt to this new appliance, we advise
you to shave regularly (at least 3 times a week) and
exclusively with this appliance for a period of 3
weeks.
Dry shaving
1Switch on the appliance.
12 English

2Move the shaving heads over your skin in
circular movements to catch all hairs growing in
different directions. Make sure each shaving
head is fully in contact with the skin. Exert
gentle pressure for a close, comfortable shave.
Note: Do not press too hard, as this can cause
skin irritation.
3Clean the appliance after use (see 'Cleaning
and maintenance').
Wet shaving
For a more comfortable shave, you can also use
this appliance on a wet face with shaving foam or
shaving gel.
To shave with shaving foam or shaving gel, follow
the steps below:
1Apply some water to your skin.
2Apply shaving foam or shaving gel to your skin.
3Rinse the shaving unit under the tap to ensure
that the shaving unit glides smoothly over your
skin.
4Switch on the appliance.
13
English

5Move the shaving heads over your skin in
circular movements to catch all hairs growing in
different directions. Make sure each shaving
head is fully in contact with the skin. Exert
gentle pressure for a close, comfortable shave.
Note: Do not press too hard, this can cause skin
irritation.
Note: Rinse the shaving unit regularly to ensure
that it continues to glide smoothly over your
skin.
6Dry your face.
7Clean the appliance after use (see 'Cleaning
and maintenance').
Note: Make sure you rinse all foam or shaving gel
off the appliance.
Using the click-on attachments
Note: The accessories supplied may vary for
different products. The box shows the accessories
that have been supplied with your product.
Removing or attaching the click-on
attachments
1Make sure the appliance is switched off.
2Pull the attachment straight off the appliance.
Note: Do not twist the attachment while you
pull it off the appliance.
3Insert the lug of the attachment into the slot in
the top of the appliance. Then press down the
attachment to attach it to the appliance (‘click’).
Using the precision trimmer attachment
You can use the precision trimmer attachment to
touch up your beard, sideburns and moustache.
14 English

1Attach the precision trimmer attachment to the
appliance ('click').
2Switch on the appliance.
3Hold the trimmer perpendicular to the skin and
move the appliance downwards while you exert
gentle pressure.
4Clean the attachment after use.
Using the cleansing brush attachment
Note: For better shaving results, use the click-on
cleansing brush attachment before shaving.
Use the rotating cleansing brush with your daily
cleansing cream. The cleansing brush removes oil
and dirt, contributing to a healthy and oil-free skin.
We advise you to use it no more than twice a day.
Do not use the appliance on damaged or irritated
skin or on wounds.
1Place the attachment on the attachment
holder.
2Attach the attachment to the appliance ('click').
3Moisten the attachment with water.
Note: Do not use the appliance with a dry
cleansing brush attachment, as this can irritate
the skin.
15
English

4Moisten your face with water and apply a
cleanser to your face.
5Place the attachment on your cheek.
6Switch on the appliance.
20 sec.
7Gently move the brush across your skin from
the nose towards the ear. Do not push the
brush too hard onto the skin to make sure that
the treatment remains comfortable.
Note: Do not cleanse the sensitive area around
your eyes.
20 sec.
8After approx. 20 seconds, move the appliance
to your other cheek and start cleansing this part
of your face.
20 sec.
9After approx. 20 seconds, move the appliance
to your forehead and start cleansing this part of
your face. Gently move the brush head from left
to right.
Note: We advise you to not overdo the
cleansing and to not cleanse any zone longer
than 20 seconds.
10 Switch off the appliance and clean the
attachment after use.
11 After the treatment, rinse and dry your face.
Your face is now ready for the next step of your
daily skincare routine.
16 English

Cleaning and maintenance
Cleaning the shaver under the tap
Clean the shaver after every use for optimal
performance (see 'Cleaning and maintenance').
Be careful with hot water. Always check if the
water is not too hot, to prevent burning your
hands.
Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.
1Switch on the appliance.
2Rinse the shaving unit under a warm tap.
3Switch off the appliance. Pull the shaving head
holder off the bottom part of the shaving unit.
4Rinse the hair chamber under the tap.
5Rinse the shaving head holder under a warm
tap.
6Carefully shake off excess water and let the
shaving head holder air-dry completely.
17
English

7Attach the shaving head holder to the bottom
part of the shaving unit (‘click’).
Thorough cleaning
We advise you to clean the shaving heads
thoroughly once a month or when the appliance
does not shave as well as it used to.
1Switch off the appliance.
2Pull the shaving head holder off the bottom
part of the shaving unit.
3Rinse the hair chamber and shaving head
holder under the tap.
4Turn the retaining ring anticlockwise and lift it
off the shaving head.
1
2
Repeat this process for the other retaining rings.
Place them aside in a safe place.
18 English

5Remove the shaving heads from the shaving
head holder. Each shaving head consists of a
cutter and guard.
Note: Do not clean more than one cutter and
guard at a time, since they are all matching sets.
If you accidentally put a cutter in the wrong
shaving guard, it may take several weeks before
optimal shaving performance is restored.
6Clean the cutter and guard under the tap.
7Shake off excess water.
8Put the cutter back into the guard.
9Place the shaving heads in the shaving head
holder.
Note: Make sure the notches on both sides of
the shaving heads fit exactly onto the
projections in the shaving head holder.
10 Place the retaining ring on the shaving head
and turn it clockwise to reattach the retaining
ring.
Place the arrows on the ring in line with the
projections in the shaving head holder. Turn the
ring clockwise until it clicks to indicate that the
ring is fixed.
Hold the shaving head holder in your hand
when you reinsert the shaving heads and
reattach the retaining rings. Do not place the
shaving head holder on a surface when you do
this, as this may cause damage.
11 Attach the shaving head holder to the bottom
part of the shaving unit (‘click’).
19
English

Cleaning the click-on attachments
Never dry trimmer attachment with a towel or
tissue, as this may damage the trimming teeth.
Cleaning the precision trimmer attachment
Clean the trimmer attachment after each use.
1Switch on the appliance with the precision
trimmer attachment attached.
2Rinse the attachment under a warm tap.
3After cleaning, switch off the appliance.
4Carefully shake off excess water and let the
attachment air-dry completely.
For optimal performance, lubricate the teeth of the
attachment with a drop of sewing machine oil
every six months.
Cleaning the cleansing brush attachment
Clean the cleansing brush attachment after each
use.
1Switch off the appliance.
2Detach the brush head from the attachment
holder.
3Clean the parts thoroughly with warm water
and soap.
4Dry the cleansing brush attachment with a
towel.
Storage
Store the appliance in the pouch (if supplied).
Note: We advise you to let the appliance dry
before you store it in the pouch.
20 English