Philips S91 series User manual
S91xx/S90xx
1
4
Introduction
Congratulations on your purchase and welcome to Philips!
product at www.philips.com/welcome.
this shaver as well as some tips to make shaving easier and more enjoyable.
General description (Fig. 1)
1 Comb for beard styler attachment
2 Click-on beard styler attachment
3 Click-on trimmer attachment
4 Click-on shaving unit
5 On/off button
6 Socket for small plug
7 Exclamation mark
8 Replacement reminder
9 Battery charge indicator
10 Travel lock symbol
11 Cleaning reminder
12 Replacement symbol
13 SmartClean system
14 Cap of SmartClean system
15 On/off button
16 Cleaning symbol
17 Drying symbol
18 Ready symbol
19 Charge symbol
20 Cleaning cartridge for SmartClean system
21 Adapter
22 Small plug
23 Retaining ring holder
24 Pouch
Note:The accessories supplied may vary for different products.The box shows
the accessories that have been supplied with your appliance.
Important
Read this user manual carefully before you use the shaver and
the SmartClean system. Save this user manual for future reference.
Danger
- Keep the adapter dry.
Warning
- The adapter contains a transformer. Do not cut off the adapter to
- The shaver and the SmartClean system are not intended for use
have been given supervision or instruction concerning use of these
appliances by a person responsible for their safety.
ENGLISH
- Children should be supervised to ensure that they do not play with
the shaver and the SmartClean system.
- Always unplug the shaver before you clean it under the tap.
Caution
- Never immerse the SmartClean system in water nor rinse it under
the tap.
- Never use water hotter than 80°C to rinse the shaver.
-
adapter or part with one of the original type.
- Only use the SmartClean system with the original cleaning cartridge.
-
surface to prevent leakage.
- Always make sure that the cartridge compartment is closed before you
use the SmartClean system to clean or charge the shaver.
-
- The SmartClean system thoroughly cleans but does not disinfect your
-
aggressive liquids such as petrol or acetone to clean the appliance.
- Water may leak from the socket at the bottom of the shaver when you
rinse it.This is normal and not dangerous because all electronics are
enclosed in a sealed power unit inside the shaver.
Compliance with standards
- This shaver is waterproof and complies with the internationally
approved safety regulations. It is suitable for use in the bath or shower
therefore only be used cordlessly.
- The shaver and the SmartClean system comply with all applicable
General
- The adapter is equipped with an automatic voltage selector and is
suitable for mains voltages ranging from 100 to 240 volts.
- The adapter transforms 100-240 volts to a safe low voltage of less
than 24 volts.
- Maximum noise level: Lc = 69dB(A)
from the display.
- S91XX/SH90XX
ENGLISH 5
Charging
- Charging takes approx. 1 hour.
Note:This appliance can only be used cordlessly.
-
it produces a sound.Then the lights of the battery charge indicator light
up one after the other continuously.When the shaver contains enough
-
shaver is fully charged.
Note:This appliance can only be used cordlessly.
you hear a sound to indicate that the shaver is still connected to the mains.
-
indicator light up white continuously.
-
you hear a sound.
- The remaining battery capacity is indicated by the lights of the battery
charge indicator that light up continuously.
ENGLISH6
Cleaning reminder
every use.
-
remind you to clean the shaver.
You can lock the shaver when you are going to travel.The travel lock
prevents the shaver from being switched on by accident.
1 Press the on/off button for 3 seconds to enter the travel lock mode.
,While you activate the travel lock, the travel lock symbol lights up
white continuously.When the travel lock is activated, the shaver
1 Press the on/off button for 3 seconds.
,
The shaver is now ready for use again.
Note:You can also deactivate the travel lock by connecting the appliance to
the mains.
ENGLISH 7
heads every two years.
- The appliance is equipped with a replacement reminder which reminds
you to replace the shaving heads.The replacement reminder lights up
indicate you have to replace the shaving heads.
pressing the on/off button for 7 seconds.
-
continuously.The replacement reminder and the cleaning reminder
cannot run because the shaving heads are soiled or damaged.
-
them.
-
orange.
-
continues once the appliance is back to the normal temperature.
Charging
Charging takes approx. 1 hour.
A fully charged shaver has a shaving time of up to 50 minutes.
Note:You cannot use the appliance while charging.
indicates that the battery is almost empty .
Charging with the adapter
1 Make sure the appliance is switched off.
2 Insert the small plug into the appliance (1) and put the adapter in the
wall socket (2).
ENGLISH8
1 Put the small plug in the SmartClean system.
2 Put the adapter in the wall socket.
3 Press the top cap to be able to place the shaver in the holder
(‘click’).
4 Hold the shaver upside down above the holder. Make sure the front
of the shaver points towards the SmartClean system.
5 Place the shaver in the holder (1), tilt the shaver backwards (2) and
press down the top cap to connect the shaver (‘click’) (3).
may even become slightly irritated.This is normal.Your skin and beard need
time to adapt to any new shaving system.
We advise you to shave regularly (at least 3 times a week) with this shaver
for a period of 3 weeks to allow your skin to adapt to the new shaver.
not shaved for 3 days or longer.
Note:This appliance can only be used cordlessly.
1 Press the on/off button once to switch on the shaver.
,The display lights up for a few seconds.
ENGLISH 9
2 Move the shaving heads over your skin in circular movements.
- Do not make straight movements.
3 Press the on/off button once to switch off the shaver.
,The display lights up for a few seconds and then shows the remaining
battery charge.
You can also use this shaver on a wet face with shaving foam or shaving gel.
1 Apply some water to your skin.
2 Apply shaving foam or shaving gel to your skin.
3 Rinse the shaving unit under the tap to ensure that the shaving unit
glides smoothly over your skin.
4 Press the on/off button once to switch on the shaver.
5 Move the shaving heads over your skin in circular movements.
Note: Rinse the shaver under the tap regularly to ensure that it continues to
glide smoothly over your skin.
6 Dry your face and thoroughly clean the shaver after use (see chapter
‘Cleaning and maintenance’).
Note: Make sure you rinse all foam or shaving gel off the shaver.
ENGLISH10
Note:The accessories supplied may vary for different products.The box shows
the accessories that have been supplied with your appliance.
You can use the trimmer attachment to groom your sideburns and
moustache.
1 Pull the shaving unit straight off the appliance.
Note: Do not twist the shaving unit while you pull it off the appliance.
2 Insert the lug of the trimmer attachment into the slot in the top of
the shaver.Then press down the trimmer attachment to attach it to
the appliance (‘click’).
3 Press the on/off button once to switch on the appliance.
,The display lights up for a few seconds.
4 You can now start trimming.
5 Press the on/off button once to switch off the appliance.
,The display lights up for a few seconds to show the remaining
battery charge.
6 Pull the trimmer attachment straight off the appliance.
Note: Do not twist the trimmer attachment while you pull it off the appliance.
7 Insert the lug of the shaving unit into the slot in the top of the
appliance.Then press down the shaving unit to attach it to the
appliance (‘click’).
1 Make sure the appliance is switched off.
2 Pull the shaving unit straight off the appliance.
Note: Do not twist the shaving unit while you pull it off the appliance.
ENGLISH 11
3 Insert the lug of the beard styler attachment into the slot in the top
of the appliance.Then press down the beard styler attachment to
attach it to the appliance (‘click’).
You can use the beard styler attachment with the comb attached to style
length settings on the beard styler attachment correspond to the remaining
hair length after cutting and range from 1 to 5mm.
1 Slide the comb straight into the guiding grooves on both sides of the
beard styler attachment (‘click’).
2 Press the length selector and then push it to the left or right to
select the desired hair length setting.
3 Press the on/off button once to switch on the appliance.
4 You can now start styling your beard.
You can use the beard styler attachment without the comb to contour
1 Pull the comb off the beard styler attachment.
Note: Grab the comb in the centre to pull it off the beard styler attachment.
Do not pull at the sides of the comb.
2 Press the on/off button once to switch on the appliance.
ENGLISH12
3 You can now start contouring your beard, moustache, sideburns or
neckline.
Cleaning and maintenance
Note:The accessories supplied may vary for different products.The box shows
the accessories that have been supplied with your appliance.
The SmartClean system comes in two types.The features available on your
SmartClean system may differ per type:
- SmartClean system Basic has one phase: the rinsing phase.
- SmartClean system Plus has two phases: the rinsing phase and the
drying phase.
Do not tilt the SmartClean to prevent leakage.
Note: Hold the SmartClean while you prepare it for use.
1 Put the small plug in the back of the SmartClean system.
2 Put the adapter in the wall socket.
3 Press the button on the side of the SmartClean system (1) and lift
the top part of the SmartClean system (2).
ENGLISH 13
4 Pull the seal off the cleaning cartridge.
5 Place the cleaning cartridge in the SmartClean system.
6 Push the top part of the SmartClean system back down (‘click’).
Always make sure to shake excess water off the shaver before you place
it in the SmartClean.
1 Press the top cap to be able to place the shaver in the holder
(‘click’).
ENGLISH14
2 Hold the shaver upside down above the holder. Make sure the front
of the shaver points towards the SmartClean system.
3 Place the shaver in the holder (1), tilt the shaver backwards (2)
and press down the top cap to connect the shaver (‘click’) (3).
,
is charging.
4 Press the on/off button on the SmartClean system to start the
cleaning program.
,
Note:The rinsing phase takes approx. 10 minutes.
,SmartClean systems Plus only:
Note:The drying phase takes approx. 4 hours.
,When the cleaning program has been completed, the ready symbol
lights up continuously.
,The battery symbol lights up continuously to indicate that the shaver
is fully charged.
Note: Charging takes approx. 1 hour.
Note: If you press the on/off button of the SmartClean system during the cleaning
Note: If you remove the adapter from the wall socket during the cleaning
Note: 30 minutes after the cleaning program and charging have been
ENGLISH 15
-
1 Press the button on the side of the SmartClean system (1) and lift
the top part of the SmartClean system (2).
2 Take the empty cleaning cartridge from the SmartClean system and
3 Throw away the empty cleaning cartridge.
4 Unpack the new cleaning cartridge and pull the seal off the cartridge.
5 Place the new cleaning cartridge in the SmartClean system.
6 Push the top part of the SmartClean system back down (‘click’).
Clean the shaver after every shave for optimal shaving performance.
Be careful with hot water.Always check if the water is not too hot,
to prevent your hands from getting burnt.
Never dry the shaving unit with a towel or tissue, as this may damage the
shaving heads.
ENGLISH16
1 Rinse the shaving unit under a warm tap for some time.
2 Pull the shaving head holder off the bottom part of the shaving unit.
3 Rinse the shaving head holder under a warm tap.
4 Carefully shake off excess water and let the shaving head holder dry.
5 Reattach the shaving head holder to the bottom part of the shaving
unit (‘click’).
Make sure the appliance is switched off.
1 Pull the shaving head holder off the bottom part of the shaving unit.
2 Place the retaining ring holder on the retaining ring (1), turn it
anticlockwise (2) and lift it off the shaving head (3).
Remove the retaining ring from the retaining ring holder and repeat this
process for the other retaining rings.
ENGLISH 17
3 Remove the shaving heads from the shaving head holder. Each shaving
head consists of a cutter and guard.
it may take several weeks before optimal shaving performance is restored.
4 Clean the cutter and guard under the tap.
5 After cleaning, place the cutter back into the guard.
6 Put the shaving heads back into the shaving head holder.
7 Place the retaining ring holder on the retaining ring (1), place it
on the shaving head (2) and turn it clockwise (3) to reattach the
retaining ring.
Repeat this process for the other retaining rings.
ENGLISH18
Note: Hold the shaving head holder in your hand when you reinsert the
shaving heads and reattach the retaining rings. Do not place the shaving head
8 Reattach the shaving head holder to the bottom part of the
shaving unit.
Cleaning the trimmer attachment
Clean the trimmer attachment every time you have used it.
1 Switch on the appliance with the trimmer attachment attached.
2 Rinse the trimmer attachment under a hot tap for some time.
3 Carefully shake off excess water and let the trimmer attachment dry.
4 After cleaning, switch off the appliance.
of sewing machine oil every six months.
Clean the beard styler attachment every time you have used it.
1 Pull the comb off the beard styler attachment.
2 Rinse the beard styler attachment and the comb separately under a
hot tap for some time.
3 Carefully shake off excess water and let the beard styler
attachment and comb dry.
4 Lubricate the teeth with a drop of sewing machine oil every
six months.
Storage
1 Store the shaver in the pouch supplied.
Note:We advise you to let the shaver dry before you store it in the pouch.
ENGLISH 19
Replacement
heads every two years.
Replacement reminder
The shaving unit symbol lights up to indicate that the shaving heads need to
be replaced. Replace damaged shaving heads right away.
Only replace the shaving heads with original SH90 Philips shaving heads.
1
white and you hear a beep when you switch off the shaver .
2 Pull the shaving head holder off the bottom part of the shaving unit.
3 Place the retaining ring holder on the retaining ring (1), turn it
anticlockwise (2) and lift it off the shaving head (3).
Remove the retaining ring from the retaining ring holder and repeat this
process for the other retaining rings.
4 Remove the shavings heads from the shaving head holder and throw
them away.
5 Place new shaving heads in the holder.
ENGLISH20
Other manuals for S91 series
6
This manual suits for next models
2
Table of contents
Other Philips Electric Shaver manuals
Philips
Philips Norelco 6900LC User manual
Philips
Philips S3561 User manual
Philips
Philips HQ8253 User manual
Philips
Philips AquaTouch AT750 User manual
Philips
Philips HQT764 User manual
Philips
Philips HQ7360 User manual
Philips
Philips HQ6990/16 User manual
Philips
Philips S5000 series User manual
Philips
Philips HP6383 User manual
Philips
Philips S100 Series User manual
Philips
Philips QG3340 User manual
Philips
Philips Norelco Beardtrimmer 3000 Instruction Manual
Philips
Philips NORELCO BT5210 User manual
Philips
Philips RQ111/52 User manual
Philips
Philips QT4013/15 User manual
Philips
Philips T765/60 User manual
Philips
Philips MicroAction 4402LC User manual
Philips
Philips HQ9190 User manual
Philips
Philips 3000 series Operating instructions
Philips
Philips HP6335 User manual
