Philips GC9080/06 User manual

GC9080

2

3

4

ENGLISH 6
DEUTSCH 13
FRANÇAIS 20
NEDERLANDS 27
ESPAÑOL 34
ITALIANO 41
PORTUGUÊS 48
 55
GC9080

General description
AIroning board cover
BSocket for steam tank
CCord storage compartment
DSteam tank tray
ESteam tank locator
FCord winding facility
GControl panel
HFan switch (Úfor suction mode, Òfor blowing mode)
IOn/off switch (power supply to heatable ironing surface, socket for
steam tank and fan)
JMains cord
KSafety catch
LCover fastener
MHeight adjustment levers
NAdjustable feet
OWheels
Important
Read these instructions for use carefully before using the appliance and
save them for future reference.
◗Check if the voltage indicated on the type rating label corresponds
to the local mains voltage before you connect the ironing board.
The ironing board is to be connected to an earthed 16A wall
socket only.
◗Do not use the ironing board if the mains cord is damaged.
◗If the mains cord is damaged, it must be replaced by Philips, a
service centre authorised by Philips or similarly qualified persons
in order to avoid a hazard.
◗Never leave the ironing board unattended when it is connected to
the mains.
◗Keep the appliance out of the reach of children. Infirm persons
should not be allowed to use the ironing board without
supervision.
◗Do not move the ironing board when it is switched on.
◗Do not put very wet fabrics on the ironing board.
◗Never allow the hot soleplate to come in contact with the cord of
the ironing board or the cord and supply hose of the iron.
◗Always unplug the ironing board after use.
◗This appliance is intended for indoor household use only.
◗The maximum rating for the steam tank socket is 10A.
◗Do not remove or replace the ironing board cover during or
immediatetely after ironing, as the plates underneath the cover
become hot and may cause burns if touched.
ENGLISH6

Preparing for use
Setting up the ironing board
C1Check if the safety catch is securely fastened before you move
the ironing board.
Do not release the safety catch when the ironing board is in vertical
storage position.
C2The ironing board has been provided with wheels for easy
transport.
C3Put the ironing board into horizontal position with the wheels
and the adjustable feet on the floor.
C4Press and hold the safety catch with one hand and put one foot
on the front leg of the ironing board and then carefully lift the
board to the required height.
Adjusting the height of the ironing board
1To raise the ironing board, grab both sides of the board and lift
it to the required height.
C2To put the board in a lower position, press the height
adjustment levers on both sides of the ironing board and lower
the board. Release the levers when the desired height has been
reached.
You will hear a click when the ironing board locks into position.
BThere are 6 height adjustment positions.
ENGLISH 7
PHILIPS

C3If the floor is not level, turn the adjustable feet until the ironing
board is stable and firmly placed on the floor.
Using the appliance
To prevent condensation inside the ironing board, it is recommended
that you use the blowing mode periodically during steam ironing.
BTip: Also see the instruction video.
C1Pull the mains cord out of the cord storage compartment.
2Put the plug in an earthed wall socket.
C3Fold out the steam tank tray.
C4Switch the ironing board on by pushing the on/off switch to
position I.
When the ironing board is switched on, it will automatically start to
heat up.
C5Set the fan switch to suction or blowing mode.
The proper fan mode depends on the type of fabric:
◗Suction mode Ú: wool, cotton, linen.
To fix garments on the ironing board for firm pressing and better
ironing results or to make pleats in thick fabrics.
◗Blowing mode Ò: silk, synthetic fabrics (e.g. acrylic, viscose,
polyamide, polyester, etc.).
For gentle pressing of fabrics to prevent shiny patches and to avoid
unwanted creases.
ENGLISH8
OI
OI

The ironing board is now ready for use!
C◗The ironing board also allows you to iron while sitting down.
Placing the steam tank on the steam tank tray
It is recommend to use the ironing board in combination with a Philips
Intellicare (GC8080/8030) or Provapor (GC60xx) ironing system.
1Pull the steam tank locator outwards.
C2Place the steam tank firmly on the tray.
The steam tank can be placed in right-hand as well as left-hand
orientation.
3To secure the steam tank, push the steam tank locator inwards.
The steam tank is now fixed so that it cannot move sideways. However,
it can be still be lifted off the tray for storage.
C4Put the plug of the steam tank in the socket on the control
panel.
C◗Wind excess mains cord of the steam tank round the cord
winding facility of the tray.
Cleaning and maintenance
To prevent condensation inside the ironing board, it is recommended
that you use the blowing mode periodically during steam ironing.
1Remove the plug from wall socket.
C2To clean the ironing board cover, loosen the cover fastener and
remove the cover.
The cover can be machine-washed on a gentle setting and dried on the
washing line.
ENGLISH 9

Storage
Remove the steam tank from the steam tank tray before you store the
ironing board.
Be careful with the hot iron when you remove it from the ironing
board!
C1Fold the steam tank tray into storage position.
C2Unplug the ironing board and put the mains cord in the cord
storage compartment.
C3Press the height adjustment levers on both sides of the ironing
board.
C4Keep the height adjustment levers pressed and lower the
ironing board until you hear a click.
C5Lift the rear leg of the ironing board and wheel it to its storage
place.
ENGLISH10