Philips IntelliVue Arm User manual

Philips IntelliVue Arm

P502673 Rev B

IntelliVue Arm Components List
2
Wall Track Options
Select a wall track.
Choose a size that is compatible with your
application.
Wall tracks are available in different lengths.
Each has 3/8" diameter mounting holes
positioned 6" center to center apart.
8326-13-XXX - 13" Wall Track
8326-19-XXX - 19" Wall Track
8326-31-XXX - 31" Wall Track
NOTE: Customlengthtrackscanbe
manufactureduponrequest.
13 "
19 "
31"
8328-XXX Track Mount
The track mount slides into the wall track.
There is a set screw in the front of the
mount which can be used as a locking
mechanism and also controls the
articulation of the mount.

IntelliVue Arm Components List
3
8240-XXX Aluminum Collar
The aluminum collar slides up the bottom
of the adapter assembly pole and locks
into place, preventing the pole from being
removed.
Setup includes 5/32" Allen wrench
(P700147).
Monitor Arm
6958-1000-XXX
This arm is used for IntelliVue only.
6958-1500-XXX
The minimum weight that can be placed
on the arm is 32 lbs with a maximum
weight capability of 53 lbs.
Setup includes 1/4" Allen wrench
(P701127) and 3/32" Allen wrench
(P700146).
2"
10 "
Adapter Assembly Options
Select an adapter assembly size that is
compatible with your application.
The Adapter Assembly Pole is available in
two different lengths.
61302-10-XXX - 10" Pole
(Used for the IntelliVue adapter plug)
61302-2-XXX - 2" Pole
(Use when adapter plug is not required)
NOTE:Eachadaptersizeincludes(4)1/4-20x
1/2"PhilipsFlatHeadScrews.

IntelliVue Arm Assembly Instructions
4

IntelliVue Arm Assembly Instructions
5


The four anchorage methods illustrated
in the next few pages represent load tests
made to comply with California OSHPD
requirements for the anchorage and
installation of instrument support system.
OSHPD requires that such support
systems resist a lateral force of 2 times
the weight of the instrument and a vertical
force of 2.2 times that weight applied
simultaneously.
For 5/8" Gypsum Board walls to comply
with CA seismic requirements for wall
mounted instrumentation. CA OSHPD
Anchorage pre-approval number TBA.
Anchorage or support of metal stud wall
must be verified by the project engineer
and approved by OSHPD prior to the
installation of any mounting system.




IntelliVue Arm Assembly Instructions
6


The four anchorage methods illustrated
in the next few pages represent load tests
made to comply with California OSHPD
requirements for the anchorage and
installation of instrument support system.
OSHPD requires that such support
systems resist a lateral force of 2 times
the weight of the instrument and a vertical
force of 2.2 times that weight applied
simultaneously.
For 5/8" Gypsum Board walls to comply
with CA seismic requirements for wall
mounted instrumentation. CA OSHPD
Anchorage pre-approval number TBA.
Anchorage or support of metal stud wall
must be verified by the project engineer
and approved by OSHPD prior to the
installation of any mounting system.




IntelliVue Arm Assembly Instructions
7


The four anchorage methods illustrated
in the next few pages represent load tests
made to comply with California OSHPD
requirements for the anchorage and
installation of instrument support system.
OSHPD requires that such support
systems resist a lateral force of 2 times
the weight of the instrument and a vertical
force of 2.2 times that weight applied
simultaneously.
For 5/8" Gypsum Board walls to comply
with CA seismic requirements for wall
mounted instrumentation. CA OSHPD
Anchorage pre-approval number TBA.
Anchorage or support of metal stud wall
must be verified by the project engineer
and approved by OSHPD prior to the
installation of any mounting system.




IntelliVue Arm Assembly Instructions
8


The four anchorage methods illustrated
in the next few pages represent load tests
made to comply with California OSHPD
requirements for the anchorage and
installation of instrument support system.
OSHPD requires that such support
systems resist a lateral force of 2 times
the weight of the instrument and a vertical
force of 2.2 times that weight applied
simultaneously.
For 5/8" Gypsum Board walls to comply
with CA seismic requirements for wall
mounted instrumentation. CA OSHPD
Anchorage pre-approval number TBA.
Anchorage or support of metal stud wall
must be verified by the project engineer
and approved by OSHPD prior to the
installation of any mounting system.




IntelliVue Arm Assembly Instructions
9


All tracks have 3/8" diameter mounting
holes positioned 6" center to center apart.
Determine where you will be placing the
track and drill appropriate holes.
Position the mount track (8326-#-XXX)
on the wall.
Insert mounting screws (P701274)
through the pre-drilled holes on the track.
Use 3/16" Allen wrench (P701311) and
tighten the screws in the wall.
The length of the track you’ve selected
will depend on how many mounting holes
there are and how many mounting screws
(P701274) you will need. For this example
a 19" track has been selected.
NOTE:Donotfastendirectlyintosheetrock,
plasterordrywall.Consultthefacilitiespersonnel,
installeroryourlocalhardwarestoreifyouhave
anyquestionsonwhatfastenerisappropriatefor
yourwallsurface.
Wall Track
Part No. 8326-#-XXX
1/4-20 x 1-3/4"
Socket Cap Screw
Part No. P701274

IntelliVue Arm Assembly Instructions
10


Align the mount (8328-XXX) in the
grooves at the top of the wall track. Slide
it down to the desired height and tighten
the set screws to lock into place using
the 3/32" Allen wrench (P700146).
Track Mount
Part No. 8328-XXX

IntelliVue Arm Assembly Instructions
11


Insert the monitor arm (6958-#-XXX) into
the track mount (8238-XXX).
Track Mount
Part No. 8328-XXX
Monitor Arm
Part No. 6958-#-XXX

IntelliVue Arm Assembly Instructions
12


Insert the adapter (61302-#-XXX) in the
end of the forearm.
Align the IntelliVue connector plug
(included with the IntelliVue) over the
adapter (61302-#-XXX) and tighten using
the (4) 1/4-20 x 1/2" Philips Flat Head
Screws (P700987).
Slide the collar (8240-XXX) up the pole
and tighten the set screw to secure. Slide
the washer (P700566) and retaining ring
(P700567) onto the pole. Secure the
retaining ring with retaining ring pliers.
Retaining ring pliers can be purchased at
your local hardware store.
NOTE:AttachtheIntelliVueconnectorplugtothe
adapterandtightenusingscrews.
1/4-20 x 1/2"
Philips Flat Head Screw
Part No. P700987
Monitor Arm
Part No. 6958-#-XXX
Pole
Part No. 61302-#-XXX
Aluminum Collar
Part No. 8240-XXX
Washer
Part No. P700566
Retaining Ring
Part No. P700567

IntelliVue Arm Assembly Instructions
13


Included you will receive (2) pieces of 11"
cable management (P401136).
Remove the backing and attach the first
piece to the underside of the forearm.
This will keep your cords organized. Be
sure to leave enough slack for cables to
loop around the elbow of the arm.
Remove the backing on the second piece
and attach it to the underside of the lower
channel.
Cable Managers
Part No. P401136

IntelliVue Arm Assembly Instructions
14


Included you will receive (2) wall track
end caps (P104596), (1) wall track cable
cap (P104985) and (1) wall mount cable
cap (P104599).
Cut the track mount cable cap to desired
length. The wall track cable cap snaps
into the wall track.
The track end caps simply plug into the
top and bottom of the track.
Wall Track End Cap
Part No. P104596
Wall Mount Cable Cap
Part No. P104599
Wall Track Cable Cap
Part No. P104985

IntelliVue Arm Operating Manual
15

It is recommended that all the hardware
associated with the mounting system
be periodically checked and tightened.

The arm can be cleaned with any non-
abrasive solution as approved by the
facility in which the product will be used.
Stronger Weaker
Stronger Weaker

Use the 3/32" Allen wrench (P700146) to
adjust (3) articulation points.

Hold the arm in a horizontal position.
Use the 1/4" Allen wrench (P700146)
to strengthen or weaken.

Note:
