ClipperCreek CS EVSE Pedestal User manual
Innovative Infrastructure for
Electric and Hybrid Vehicles
CS EVSE PEDESTAL
INSTALLATION GUIDE
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
PLEASE NOTE:
This installation guide includes the latest information at the time of printing. ClipperCreek, Inc. reserves the right to
Before Beginning:
Note to the Installer:
Note to the User:
Keep these instructions for further reference.
Download or view the most recent version of this Installation Guide at:
WARNING: This product can expose you
to chemicals, including Carbon Black, which
is known to the State of California to cause
cancer. For more information go to:
www.P65Warnings.ca.gov
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS 5
INSTALLATION REQUIREMENTS 5
TOOLS REQUIRED FOR ASSEMBLING THE CS PEDESTAL KIT 6
TOOLS REQUIRED FOR WIRING THE CS EVSE
PEDESTAL DIMENSIONS 7
PACKING LISTS 8
INITIAL PEDESTAL INSTALLATION 9
FINAL PEDESTAL INSTALLATION
CUSTOMER SUPPORT
WARRANTY INFORMATION
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
FIGURES
........................................................
........................................................
.................................................
...............................................................
...........................................
........................................................
......................................................
...............................................
................................................
...............................................
.................................................
........................................
.........................................................
...................................................
................................
..................................................
..................................
..............................
...
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
IMPORTANT SAFETY INSTRUCTIONS
electrical codes and ordinances.
electrical codes and ordinances.
DO NOT attempt to perform a
INSTALLATION REQUIREMENTS
1
Refer to the EVSE documentation to determine the appropriate circuit breaker current capacity.
2All conductors must be appropriately sized for the EVSE current capacity, in accordance with local and NEC electrical codes.
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
TOOLS REQUIRED FOR ASSEMBLING THE CS PEDESTAL
The following tools are required for the installation and assembly of the pedestal components:
(Alternatively, a ratcheting driver
TOOLS REQUIRED FOR WIRING THE CS EVSE
circuit of up to
greater than
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
PEDESTAL DIMENSIONS
Figure 2: Pedestal Base Dimensions
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
OPTIONAL ORDERABLE ITEMS
(Optional Extension Compatible)
Part Number QTY Description
PACKING LISTS
Part Number QTY Description
Part Number QTY Description
Part Number QTY Description
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
The location, dimensions, and composition of the
dimensions are minimum recommended values.
side.
corresponds to the corner cutouts in the
corresponds to the inner cutouts of the
Maximum Anchor Bolt Height:
Use the Pedestal Base Pattern Template:
pedestal kit. A template is provided as
Figure 5: Bolt Pattern Template
INITIAL PEDESTAL INSTALLATION
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
through the underground conduit, the pedestal post
• Feed all service conductors up through the
inside of the pedestal post. e conductors
must be of sucient length to pass beyond
the top of the pedestal so that nal connections
can be worked with comfortably at a later step.
• Align the pedestal post base notches with the
four anchor bolts and ease it into place.
•
Nuts and washers may be used under the
pedestal base to adjust the vertical alignment of
the pedestal should the concrete pad not be level.
• Secure the pedestal post base to the concrete
anchor bolts using appropriately sized nuts and
washers.
• e anchor bolts, nuts and washers used for
the installation of the pedestal base are
not included in the pedestal kit and must be
purchased separately.
Figure 6: Pedestal Post Mounting by Pattern
INITIAL PEDESTAL INSTALLATION (continued)
• The two covers are of an identical overlapping
design.
inside of the opposite cover.
• Align the four screw holes of each cover piece
with the corresponding screw holes on
the opposite cover.
Figure 7: The Pedestal Base Covers
Wire Access Hole
Wire Access
Hole
Your
may vary
slightly
from what is
depicted in
A pedestal cap is provided to cover the opening to
protect the conductors and inner pedestal from the
post for protection during shipping. Remove the Cap
from the top of the pedestal
Figure 8: Pedestal Post Cap Removal
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
The service conductors are routed through the side
installation, these instructions must be repeated for
Figure 9 to
pedestal kit.
Access will be
from the top of the pedestal on the left side.
(a) from the end of the
conduit.
• Route the three conductors through the
washer is on the outside
washer is on the outside
•
locknut (a) onto the conduit threads.
•
IMPORTANT: Remove the locknut (f) at the
end of the conduit assembly; this will be
needed in a later step. See locknut (f) in
Figure 9. Face the open end of the 90 degree
conduit tting forward for later insertion into
the back of the EVSE.
INITIAL PEDESTAL INSTALLATION (continued)
a.
c.
d.
e. f.
b.
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
INITIAL PEDESTAL INSTALLATION (continued)
to
completed at this time. Access will be limited
from the top of the pedestal on the left side.
conduit.
• Route the three conductors through the
washer is on the outside
the washer is on the outside
to make it easier to pull the conduit through
• IMPORTANT: Remove the locknut (f) at
the end of the conduit assembly; this will
a.
b.
c.
e.
d.
f.
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
INITIAL PEDESTAL INSTALLATION (continued)
A pedestal cap is provided to cover the opening to
protect the conductors and inner pedestal from the
elements. Install the appropriate pedestal cap for a
standard post cap provided in the pedestal kit.
• Align the screw hole on each side of the post
cap with the corresponding threaded insert on
the side of the pedestal.
washer should face the head of the screw
while the neoprene should face the tip of the
screw.
replacement post cap provided in the
the pedestal.
• Align the screw hole on each side of the post
cap with the corresponding threaded insert on
the side of the pedestal.
the washer should face the head of the screw
while the neoprene should face the tip of the
screw.
The replacement post cap
back side to accomodate
a second EVSE mounting
The standard post cap has
back side
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
Install the Single CS EVSE Back Bracket
pedestal kit to make the installation more rigid and to
Note that this bracket is not used for dual
EVSE installations.
has a metal notch in the middle to
accommodate a screw hole.
•
Align the two screw holes along the centerline
•
washer should face the head of the screw while
the neoprene should face the tip of the screw.
Note that the neoprene washer must be used
to maintain a watertight seal.
front side of the pedestal post with the notch
toward the left side to allow clearance
for the conduit as shown in
• Align the two screw holes along the centerline
of the mounting plate with the corresponding
threaded inserts on the front of the pedestal
post.
of the mounting plate.
mounting plate. This second mounting plate is
the surface of the mounting plate.
INITIAL PEDESTAL INSTALLATION (continued)
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
MOUNTING THE EVSE(s)
EVSE Knockout Removal
conduit entrance. Refer to
Mounting a Single EVSE to the Pedestal
.
This operation should be performed by two
installers, one to hold the EVSE in place
while the other secures the pedestal hardware
washer should face the head of the screw
while the neoprene should face the tip of the
screw.
holes in the mounting plate and the
Use Rear Wall
Knockout
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
•
Thread the remaining conduit locknut onto the
Applysiliconesealanttolltheconduitwhere
itenterstheenclosure.Useasucientquantity
of silicone to ensure that no water or debris may
enter the enclosure through the conduit.
Mounting Two EVSE with Side Brackets
MOUNTING THE EVSE(s) and FINAL PEDESTAL INSTALLATION
Mounting Two EVSE to the Pedestal
This operation should be performed by two
installers, one to hold the EVSE in place
while the other secures the pedestal hardware
•
washer should face the head of the screw while
the neoprene should face the tip of the screw.
screw holdes in the front mounting plate.
•
Align the two threaded inserts of each side
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
Service
Ground Terminal Block.
• Tighten the Service Ground Terminal screw
screwdriver.
latch. Replace the two door screws on the left
Do not overtighten.
operational and maintenance information.
Figure 20.
further operational and maintenance
information.
FINAL PEDESTAL INSTALLATION
•
unit on the lower right hand corner of the
(If using a powered screwdriver, set it to a
•
nstall the CS Series Connector Holster(s)
INSTALLATION OF THE CS EVSE IS NOW COMPLETE. PLEASE REFER TO THE CS USER MANUAL
FOR TROUBLE-SHOOTING AND ADDITIONAL INFORMATION.
Figure 20: Loosely Wrap Cable Counter Clockwise
around the the Cradle
Cradle
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
CUSTOMER SUPPORT
PLEASE HAVE THE
Distributor Service
Number Here
CS EVSE PEDESTAL INSTALLATION GUIDE
ClipperCreek,Inc.
WARRANTY INFORMATION
LIMITED WARRANTY
ELECTRIC VEHICLE SUPPLY EQUIPMENT and ACCESSORIES
ClipperCreek, Inc.
To obtain warranty service:
11850 Kemper Rd., Suite E
Auburn, CA 95603
www.ClipperCreek.com
(877) 694-4194
Table of contents
Popular Rack & Stand manuals by other brands
Falcon
Falcon LA Series installation instructions
PCB Piezotronics
PCB Piezotronics 080B177 Installation and operating manual
Elite Industries
Elite Industries EL-904 Assembly instructions
PEERLESS
PEERLESS Smartmount ST670 Installation and assembly
Altelix
Altelix BMP-EER1 installation guide
TRINITY Pro
TRINITY Pro TBTZ-0949 owner's manual
Vantage Hearth
Vantage Hearth VHA-1156 quick start guide
Manhattan
Manhattan 460941 install guide
Next Level Racing
Next Level Racing GT Lite instruction manual
iOptron
iOptron SmartStar MiniTower Pro instruction manual
Interlogix
Interlogix TVP-CBB installation instructions
Konig & Meyer
Konig & Meyer 80370 Series quick start guide