Philips MX5800SA User manual

CLASS 1
LASER PRODUCT
Service Manual
Service
Service
Service
Service
Service
MX5800SA/21R/21S/22S/78
TABLE OF CONTENTS
Page
Location of pc boards & Version variations ................1-2
Technical Specifications .............................................1-3
Measurement setup ....................................................1-4
Service Aids, Safety Instruction, etc. .........................1-5
Disassembly Instructions & Service positions ...........2-1
Service Test Programs ...............................................3-1
Region codes setting, software upgrades, etc ...........3-3
Set Block diagram & Wiring diagram ............................ 4
P-Scan board ................................................................. 5
Front Board .................................................................... 6
ECO6 Tuner Board: System Non-Cenelec ............ 7A
System Cenelec .................... 7B
Power Module PWR207 ................................................ 8
AV Board ........................................................................ 9
5DTC Module............................................................... 10
DAC Board ................................................................... 11
Set Mechanical Exploded view & parts list ................. 12
History .......................................................................... 13
©Copyright 2003 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
Published by KC 0333 Service Audio Printed in The Netherlands Subject to modification
GB
3139 785 30231
DVD Receiver
Version 1.1
MX5900SA/37
For repair information on the SD5.00SA DVD Module, refer to Service
Manual "DVD Module SD-5.00SA_CH - 12NC: 3122 785 13830"

1-2
LOCATION OF PC BOARDS
/21R /21S /22S /33S /35S /78 /37
Karaoke x x - x x -
RDS + News - - x - - -
Progressive Scan x x - x x x
Standby - Clock Display xxxx x x
ECO Standby - No Display xxxx x x
Voltage Selector x x - - x -
Digital In / Out xxxx x x
Aux Input xxxx x x
TV Input xxxx x x
Line Output xxxx x x
SCART output - - x - - -
Pr, Pb & Y Outputs x x - x x x
CVBS Output xxxx x x
S-Video Output xxxx x x
Headphone Socket xxxx x x
P-Scan board (Faroudja P-scan) ---- - x
Tuner board - ECO6 System non-Cenelec x x - x x x
Tuner board - ECO6 System Cenelec - - x - - -
75W 6-Ch (Single SW) with 1x Amplifier pcb ---- - -
75W 7-Ch (Twin SW) with 1x Amplifier pcb xxxx x x
VERSION VARIATIONS:
Type /Versions: MX5800SA MX5800SA
Features &
Board in used:
MAIN AMPLIFER
75W
MAINS BOARD
5DTC-DVD
LOADER
MECHANISM
ECO6 TUNER
BOARD
SUPPLY
BOARD
DAC
BOARD
A/V BOARD
FRONT PANEL
(just behind the Front Panel)
P-SCAN
BOARD
SACD BOARD
(below the DAC &
P-SCAN boards)

1-3
SPECIFICATIONS
GENERAL:
Mains voltage : 110-127V/220-240V Switchable for /21./78
120V for /37
220-230V for /22S/33S
Mains frequency : 50/60Hz
Power consumption : < 0,5W at ECO Standby
< 20W Standby (clock on, demo off)
Clock accuracy : < 4 seconds per day
Dimension centre unit : 435 x 100 x 360mm
TUNER:
FM
Tuning range : 87.5-108MHz
Grid : 50kHz for /21../22S/33S
100kHz for /21../37
IF frequency : 10.7MHz ±25kHz
Aerial input : 75Ωcoaxial
Sensitivity at 26dB S/N : < 7µV
Selectivity at 600kHz bandwidth : > 25dB
Image rejection : > 25dB
Distortion at RF=1mV, dev. 75kHz : < 3%
-3dB Limiting point : < 8µV
Crosstalk at RF=1mV, dev. 40kHz : > 18dB
MW
Tuning range : 531-1602kHz for /21../22S
530-1700kHz for /21../37
Grid : 9kHz for /21../22S
10kHz for /21../37
IF frequency : 450kHz ±1kHz
Aerial input : Frame aerial
Sensitivity at 26dB S/N : < 4.0mV/M
Selectivity at 18kHz bandwidth : > 18dB
IF rejection : > 45dB
Image rejection : > 28dB
Distortion at RF=50mV, m=80% : < 5%
AMPLIFIER:
Stereo mode (DIN) : 2 x75W RMS / 2 x 60W FTC 1)
2 x 75W RMS 2)
Surround mode 3) : 75W RMS/channel
Frequency response ±3dB : 20Hz-20kHz
Hum (minimum volume) : 200nW
Residue noise (min, volume) : 40nW
Digital Sound Control : Stereo, 3D Sound, Multi modes 4)
Bass & Treble : -3 to +3 4)
Input sensitivity
TV-in : 350mV ±3dB
Aux-in : 880mV ±2dB
Output sensitivity
Line out : 600mV ±2dB at 47kΩ
Headphone (vol. max.) : 660mV ±2dB at 32Ω
COMPACT DISC/VCD/DVD:
Video Decoding : MPEG-2 / MPEG-1
Video DAC : 10 Bits
Signal System : PAL / NTSC
Video Format : 4:3 / 16:9
MP3-CD bit rate 5) : 32-256 kbs,variable bitrates
MP3-CD sampling frequencies 5) : 16kHz, 32kHz, 44.1kHz
CBVS out 6)
CVBS level : 1.0 ±0.1Vp-p
Luminance S/N ratio : > 45dB (unweighted)
YUV out 6)
Amplitude : 714mV ±7mV
S/N ratio : > 50dB (unweighted)
S-Video out 6)
Y level : 1.0 ±0.1Vp-p
Y S/N ratio : > 48dB (unweighted)
C level (burst) : 286mVp-p +1/-4 dB
Digital Out : Coaxial acc IEC61937 / IEC60958
Digital In : Coaxial acc IEC60958
1) with 4Ω, 120Hz - 12,5kHz & 10% THD for /37 only
2) with 4Ω, 1kHz & 10% THD for all version other than /37
3) with only channel(s) under meausrement loaded, all other
channels are unloaded.
4) Frequency response in each setting is software controlled.
5) Recording format: ISO9660, UDF format is not supported.
6) Output terminals terminated with 75Ω

LF Generator
e.g. PM5110
Recorder
Use Universal Test Cassette CrO2 SBC419 4822 397 30069
LEVEL METER
e.g. Sennheiser UPM550
with FF-filter
S/N and distortion meter
e.g. Sound Technology ST1700B
L
R
DUT
or Universal Test Cassette Fe SBC420 4822 397 30071
LEVEL METER
e.g. Sennheiser UPM550
with FF-filter
S/N and distortion meter
e.g. Sound Technology ST1700B
L
R
DUT
CD
Use Audio Signal Disc
(replaces test disc 3) SBC429 4822 397 30184
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
DUT
S/N and distortion meter
e.g. Sound Technology ST1700B
Frame aerial
e.g. 7122 707 89001
Tuner AM (MW,LW)
To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday´s cage.
Use a bandpass filter (or at least a high pass filter with 250Hz) to eliminate hum (50Hz, 100Hz).
RF Generator
e.g. PM5326
Ri=50Ω
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
DUT
RF Generator
e.g. PM5326
S/N and distortion meter
e.g. Sound Technology ST1700B
Use a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).
Ri=50Ω
Tuner FM
MEASUREMENT SETUP
1-4

1-5
SERVICE AIDS
Service Tools:
Universal Torx driver holder .................................. 4822 395 91019
Torx bit T10 150mm ............................................. 4822 395 50456
Torx driver set T6 - T20 ......................................... 4822 395 50145
Torx driver T10 extended ...................................... 4822 395 50423
Allen key set (1.5, 2, 2.5, 3, 4, 5, 6, 8mm) ............ 5322 395 10754
Compact Disc:
SBC426/426A Test disc 5 + 5A ............................ 4822 397 30096
SBC442 Audio Burn-in Test disc 1kHz ................. 4822 397 30155
SBC429 Audio Signals disc .................................. 4822 397 30184
SBC444/444A ........................................................ 4822 397 30245
CD-RW Printed Audio Test Disc ........................... 7104 099 96611
Dolby Pro-logic Test Disc ...................................... 4822 395 10216
ESD Equipment:
Anti-static table mat - large 1200x650x1.25mm ... 4822 466 10953
Anti-static table mat - small 600x650x1.25mm ..... 4822 466 10958
Anti-static wristband .............................................. 4822 395 10223
Connector box (1MΩ) ............................................ 4822 320 11307
Extension cable
(to connect wristband to conn. box) .................. 4822 320 11305
Connecting cable
(to connect table mat to conn. box) .................. 4822 320 11306
Earth cable (to connect product to mat or box) .... 4822 320 11308
Complete kit ESD3
(combining all above products) ......................... 4822 320 10671
Wristband tester .................................................... 4822 344 13999
HANDLING CHIP COMPONENTS

1-6
GB
WARNING
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
F
ATTENTION
Tous les IC et beaucoup d’autres
semi-conducteurs sont sensibles aux
décharges statiques (ESD).
Leur longévité pourrait être considérablement
écourtée par le fait qu’aucune précaution n’est
prise à leur manipulation.
Lors de réparations, s’assurer de bien être relié
au même potentiel que la masse de l’appareil et
enfiler le bracelet serti d’une résistance de
sécurité.
Veiller à ce que les composants ainsi que les
outils que l’on utilise soient également à ce
potentiel.
ESD
D
WARNUNG
Alle ICs und viele andere Halbleiter sind
empfindlich gegenüber elektrostatischen
Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kan
die Lebensdauer drastisch reduzieren.
Veranlassen Sie, dass Sie im Reparaturfall über
ein Pulsarmband mit Widerstand verbunden
sind mit dem gleichen Potential wie die Masse
des Gerätes.
Bauteile und Hilfsmittel auch auf dieses gleiche
Potential halten.
NL
WAARSCHUWING
Alle IC’s en vele andere halfgeleiders zijn
gevoelig voor electrostatische ontladingen
(ESD).
Onzorgvuldig behandelen tijdens reparatie kan
de levensduur drastisch doen verminderen.
Zorg ervoor dat u tijdens reparatie via een
polsband met weerstand verbonden bent met
hetzelfde potentiaal als de massa van het
apparaat.
Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
I
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono
sensibili alle scariche statiche (ESD).
La loro longevità potrebbe essere fortemente
ridatta in caso di non osservazione della più
grande cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
collegato allo stesso potenziale che quello della
massa dell’apparecchio tramite un braccialetto
a resistenza.
Assicurarsi che i componenti e anche gli utensili
con quali si lavora siano anche a questo
potenziale.
“Pour votre sécurité, ces documents
doivent être utilisés par des spécia-
listesagréés, seuls habilités à réparer
votre appareil en panne”.
GB
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified,
be used.
NL
Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in
zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen,
identiek aan de gespecificeerde, worden toegepast.
F
Les normes de sécurité exigent que l’appareil soit remis à l’état
d’origine et que soient utiliséés les piéces de rechange identiques
à celles spécifiées.
D
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu
beachten. Der Original zustand des Geräts darf nicht verändert werden;
für Reparaturen sind Original-Ersatzteile zu verwenden.
I
Le norme di sicurezza esigono che l’apparecchio venga rimesso
nelle condizioni originali e che siano utilizzati i pezzi di ricambio
identici a quelli specificati.
"After servicing and before returning set to customer perform a
leakage current measurement test from all exposed metal parts to
earth ground to assure no shock hazard exist. The leakage current
must not exceed 0.5mA."
CLASS 1
LASER PRODUCT
3122 110 03420
GB
Warning !
Invisible laser radiation when open.
Avoid direct exposure to beam.
S
Varning !
Osynlig laserstrålning när apparaten är öppnad och spärren
är urkopplad. Betrakta ej strålen.
SF
Varoitus !
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen!
DK Advarse !
Usynlig laserstråling ved åbning når sikkerhedsafbrydere er
ude af funktion. Undgå udsaettelse for stråling.

2-1 2-1
DISMANTLING INSTRUCTIONS
Dismantling of the Front Panel assembly
1) Loosen the 9 screws to dismantle the Top Cover (pos
252)
- 2 screws on each side
- 5 screws on the Rear Panel (pos 251).
Dismantling the Tuner, Mains and AV boards
2) Loosen 5 screws A and 8 catches C1 to slide the Front
Panel assembly (pos 101, 102, 103, etc) as per figure 1.
Note: To remove the Source / Volume control pc
board (pos 1105B) 2 nuts hidden below the
control knob assembly (pos 133, 134 and 135)
must first be removed.
Hints for re-assembly of Top Cover
Due to appearance design the Top cover (pos 252) is
sandwiched between the Front panel (pos 101) and the 2
side covers (pos 102 & 103), this make it necessary to
remove the 2 side covers before re-assembly of Top cover.
1) To remove the side cover use a small screw driver with
marking 16mm from the tip end.
2) Insert the screw driver into slot (as shown in figure 2) and
push the tip outwards to release the side cover catch.
The side cover can be pull outwards as soon as the top
catch is released.
Figure 2
1) Loosen 3 screws D and 2 catches C2 on the Rear panel
(pos 251) to remove theTuner board assemby (pos 1101)
as pe figure 3.
2) Loosen 1 screws E and 2 catches C3 to unslot the Mains
board (pos 1102-A) out of the Rear panel as per figure 4.
3) Loosen bracket (pos 254) by turning a catch, sliding
towards the outside and lifting it upwards as per figure 5.
4) Loosen 8 screws F (7 screws for non-Scart version) and
2 catches C5 to separate Rear Plate assembly (pos 251)
from the Bottom plate assembly (pos 227) as per figure
3.
5) Uncatch C4 to remove the AV board (pos 1104) from the
Bottom Plate assembly (pos 227) as per figure 5.
Figure 3
C5
D
FF
C5
C2
A
A
A
A
C1 C1
C1
C1
C1
C1
A
C1 C1
Figure 1
Figure 5
C4
12
Turn up the lever,
slide the bracket
as shown and lift
out of the bottom
chassis.
Figure 4
Dismantling the Supply & Power Amplifier boards
1) Loosen 2 screws B mounting the Supply board's (pos
1102-B) heatsink to the Bottom Plate (pos 227) as per
figure 6.
Note: During re-assembly care must be taken to
ensure the Mains Transformer wires to the
Supply board is routed properly below the
board.
2) Loosen 4 screws C to dismantle the Power Amplifier
board (pos 1102-D) from the Bottom Plate as per figure
6.
Figure 6

2-2 2-2
Dismantling the 5DTC Mechanism, SD-5.0SA_CH, DAC and P-Scan (only MX5900SA) boards
1) Loosen 1 screws E and 2 catches C3 to remove the
Mains board as per figure 4.
2) Loosen bracket (pos 254) by turning a catch, sliding
towards the outside and lifting it upwards as per figure 5.
3) Loosen 2 screws J and 2 catches C6 to remove the DAC
board (pos 1103-B) as per figure 7.
4) Loosen 2 screws K and 2 catches C7 to remove the P-
Scan board (pos 1107) as per figure 7 - applicable for
MX5900SA only.
5) Loosen 2 screws H to remove the bracket (pos 260) as
per figure 8.
6) Loosen 3 screws L to remove the SACD (SD-5.0SA_CH)
board (pos 1103-C) as per figure 9.
7) Loosen 3 screws G, lift up the 5DTC Module's (pos 1103-
A) rear and pull the module out towards the rear as per
figure 8.
Service position A (Top cover removed)
Service positions
Service position B (Front Panel loosen)
Figure 7
H
G
Figure 8 Figure 9

Service position C (Supply and Amplifier boards loosen) Service position D (Mains & AV boards loosen)
Service position E (5DTC Mechanism, SD-5.0SA_CH &
DAC boards loosen)
Caution:
1) In some of the service positions the Mains supply is
exposed, therefore service technicians have to exercise
care to prevent electric shock.
2) The copper pattern on the Mains board should be cov-
ered with non-conductive insulation during fault-finding
on other parts of the set.
3) Insulation sheet (eg. thick paper or cardboard) should be
use during fault-finding to prevent short-circuiting of
copper patterns to metallic surroundings.
Service positions
2-3 2-3
Thick paper
Thick paper or insulation sheet
shouldbe usedto preventpc boards
copper tracks from short-circuiting
to bottom plate
Mains Board
with non-
conductive
insulation
attached to the
copper pattern
Note:
The ground connection between AV board stoko pin
1100 and Amplifier board stoko pin 1320 must be con-
nect ed during Service pos C and D in order to have
sound output at the Loudspeakers.

3-1 3-1
Various
other Tests
Activated with ACTION TEST
SEEPROM FORMAT
TEST
Load default data. Display shows "NEW" for 1 second.
Caution!
All presets from the customer will be lost!!
Disconnect
mains cord
LEAVE SERVICE
TEST PROGRAM
T
9to Exit
EEPROM TEST Some test patterns will be sent to the EEPROM.
"PASS" is displayed if the uProcessor read back
the test patterns correctly, otherwise "FAIL" will be
displayed.
SUBW +
(Remote Control)
AUTO STANDBY
TOGGLE
Pressing this button will toggle between the status
"AUTO STANDBY ON" and "AUTO STANDBY OFF".
The status will scroll once across the Display.
SOURCE / VOLUME
Knob
ROTARY
ENCODER TEST
Display shows value for 2 seconds.
Values increases or decreases in steps of 1 until
0 (Min.) or 40 (Max.) is reached.
Figure 2
Figure 1
Y
N
Y
N
N
BII
Button pressed?
BII
Button pressed?
DISPLAY
TEST
Display shows Figure 1
and Standby LED is
Green
Display shows Figure 2
and Standby LED is
RED
Y
9
Button pressed?
Y
N
Y
N
SEATING
Button pressed?
ADC
TEST
Display shows
"ADC Value"
(Ref Table 1)
Y
N
9
Button pressed?
Note:
ADC Test is used for checking the ADC inputs to the microprocessor. The display
shows an ADC value between 0 and 255 for an input signal between 0 and 5V.
N
SEATING
Button pressed?
Y
Display shows next
"ADC Value"
(Refer Table 1)
Has it reach
"ADC5 Value" ?
Table 1
Name
ADC1
ADC2
ADC3
ADC4
ADC5
Input line to
uProcessor IC
Key0
Key1
VU_IN
MUX_DET
Options
Remarks
Return the value assign for each key button.
Return the value assign for each key button.
Varies according to the signal dc level
The set temperature is measured via this NTC
line, if lower than 69 the set goes into Standby.
Return the value assign for the different possible
options
CLOCK-TIMER
Button pressed?
Y
Y
Y
N
N
N
CLOCK-TIMER
Button pressed?
9
Button pressed?
Display shows
32K
Output at (Front Board)
pin 19 of uP = 2048Hz
Display shows
12M
Output at (Front Board)
pin 19 of uP = 2,929.6875Hz
QUARTZ
TEST
TUNING
Button pressed?
Disconnect
Mains cord ?
Y
Y
N
N
Y
Display Tuner Version
"ccc"
Service frequencies are
copied to the RAM (see Table 2)
Tuner works normally except:
PROGRAM button
Service Mode left
TUNER
TEST
TUNING
Button pressed?
N
PRESET
1
2
3
4
5
6
7
8
9
10
11
Europe
"EUR"
87.5MHz
108MHz
531kHz
1602kHz
558kHz
1494kHz
87.5MHz
87.5MHz
87.5MHz
87.5MHz
98MHz
USA
"USA"
87.5MHz
108MHz
530kHz
1700kHz
560kHz
1500kHz
98MHz
87.5MHz
87.5MHz
87.5MHz
87.5MHz
Oversea
"OSE"
87.5MHz
108MHz
530/531kHz*
1700/1602kHz*
560/558kHz*
1500/1494kHz*
98/87.5MHz*
87.5MHz
87.5MHz
87.5MHz
87.5/98MHz*
Note: * Depending on the selected grid frequency (9 or 10kHz).
By holding the "DISC5" and "STANDBY-ON" buttons depressed while switching on the Mains supply, one of the
undermentioned features will be activated:
- the tuning grid frequency is toggled between 9kHz and 10kHz for the Oversea (/21) version.
Table 2
East Europe
"EAS"
87.5MHz
108MHz
531kHz
1602kHz
558kHz
1494kHz
87.5MHz
87.5MHz
87.5MHz
87.5MHz
98MHz
East Eur. Extended-band
"EAS"
65.81MHz
108MHz
74MHz
87.5MHz
531kHz
1602kHz
558kHz
1494kHz
98MHz
70.01MHz
65.81MHz
To start service test program
hold DISC1 & STANDBY-ON
buttons depressed while
plugging in the mains cord*
Display shows the
ROM version
"S-Vyy"
S refers to Service Mode
V refers to Version
yy refers to Software version number of the uProcessor
(counting up from 01 to 99)
SERVICE TEST PROGRAM I
5DTC MX.. Range Service Test Program dd wk0302
MAIN MENU
* Hold till the Display is shown

3-2 3-2
VOL -
Button pressed?
N
DVD DEALER TEST
(without User interaction)
STEP
1
2
3
4
5
6
ACTION
Check the correctness of the
checksum in the flash.
Check the correctness of ECHO
feature
Check the correctness of the I
2
C
bus to the NVRAM
Check writing to the NVRAM
Check writing to the SDRAM
Shows result of all tests
Returns PASS or FAIL
Disconnect mains cord to exit
the Service Test Program.
DISPLAY
CHKSUM
FLASH
S2B
ECHO
IIC
NVRAM
NVRAM
WRITE
SDRAM
WRITE
ALL TEST
’####’
DVD Dealer Test is used to check the flash RAM,
the SDRAM, the DRAM, the NVRAM and the I
2
C
communication.
Y
Table 4
Error code
0601
1101
1102
1103
1104
1201
1202
1203
1204
1301
1302
1303
1304
1601
5401
5402
5403
5403
Nucleus no.
6
11
11
11
11
12
12
12
12
13
13
13
13
16
54
54
54
54
Error description
Calculated checksum of FLASH is not correct
I2C bus busy before start
NVRAM access time-out
No NVRAM acknowledge
NVRAM reply time-out
I2C bus busy
Error sending I2C command to Slave
Slave controller not responding
Slave response is not correct
Parity error receiving data from Basic Engine
Parity error sending data to Basic Engine
No communication with Basic Engine
Communication time-out with Basic Engine
The SDRAM is faulty
I2C bus busy
Error sending I2C command to Scart Switch IC
Scart Switch IC not responding
Scart Switch IC response is not correct
Nucleus Error Codes
Table 3
Faulty Module Codes
Basic Engine Part
OK
OK
Faulty
Faulty
STi + Peripherals
OK
Faulty
OK
Faulty
Error code
00
01
10
11
VOL +
Button pressed?
Y
N
DVD PLAYER TEST
(with User interaction)
STEP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
ACTION
Test picture is available on all video output. Press BII if test is ok,
otherwise press PROGRAM.
Noise is available on all channels. Press BII if test is ok,
otherwise press PROGRAM.
Internally generated pinknoise and color bar is output to all channels
& video output. Press BII if test is ok, otherwise press PROGRAM.
Internally generated pinknoise is output to all channels & test picture
(external signal) is send to video output. Press BII if test is ok,
otherwise press PROGRAM.
Sine sound output is available on all channels. Press 9to stop the
sound output. Press BII if test is ok, otherwise press PROGRAM.
The color set-up function will be tested by use of internally generated
color bar. Press BII if test is ok, otherwise press PROGRAM.
The color set-up function will be tested by use of internally generated
color bar. Press BII if test is ok, otherwise press PROGRAM.
Returns the SW-version of the basic engine.
Tray 1 can be open or close with the BII and PROGRAM buttons
repectively. Insert a CD onto Tray 1 and close before proceding
to next test.
The Sledge can be move in and out with the BII and PROGRAM
buttons respectively.
Dismotor starts to turn. Press BII if the motor turns and PROGRAM
button if the motor does not turn.
The DVD tries to focus. Press BII if focus is successful and
PROGRAM button if focus is not successful.
Radial test is started. Press BII if test is successful and PROGRAM
button if test is not successful.
The laser spot jumps to another position. Press BII to jump to the
next position or press PROGRAM to jump to previous position.
Reads out the info from the error log. Up to 16 errors (8 hex digits)
can be stored in a buffer. Press BII to view next error or press
PROGRAM to view previous error. If there is no error the display
will shows: "LO-00000000"
Shows all error bits (2-digit number). Press BII to select next error
bits or press PROGRAM to select previous error bits.
Runs the dealer test infinitely. The information returned from the
module will be displayed. aa = faulty module codes (see table 3);
bbb = number of loops and cccc = Nucleus error codes (see table 4).
Disconnect mains cord to exit Service Test
DISPLAY
BAR
PICTURE
PINK
NOISE
SCART
LOOP DVD
SCART
LOOP EXT
SINE
SOUND
COLOR
HIGH
COLOR
LOW
ENG
xx.yy.zz.
TRAY
SLEDGE
MOTOR
FOCUS
RADIAL
GROOVES
LO -
wwxxyyzz
ERROR
BITS xx
’aa-bbb’
’cccc’
Go to next
step
by pressing
T
DVD Player Test allows to start several DVD specific tests.
The user has to confirm by pressing
BII or PROGRAM button
before going to the next step.
Environment required to run the test:
- an external video source & television connected
- loudspeakers connected
DIM
Button pressed?
Y
N
DVD VERSION
MATRIX INFO
STEP
1
2
3
4
5
6
REMARKS
Slash version number
Region code setting (Number 1 - 6)
Menu language table:
US/AP - USA / Asia Pacific language
US/EU - USA / Europe language
Audio / Subtitle language table:
1 = USA
2 = Europe
3 = AP
4 = Others
Multichannel decoding available ?
Smart picture available ?
Press 9 to exit
DISPLAY
SLASH ’###’
REGION ’#’
MULANG ’US/AP’
or
MULANG ’US/EU’
ASLANG ’#’
MULTI-CH ’YES’
or
MULTI-CH ’NO’
SMARTPIC ’YES’
or
SMARTPIC ’NO’
Choose step
by pressing
S
T
DVD Version Matrix Info is used to read the version matrix information
that are stored/defined in the DVD module software.
Y
N
Y
N
MUTE
Button pressed?
Are Software
Versions Received?
DVD I
2
C
COMMUNICATION
TEST
Send request for
DVD Software Version
via I2C ports
Display shows
"xx/yyy"
"zz.zz.zz"
Display shows
"FAIL"
Y
N
9
Button pressed?
Y
N
DVD I
2
C Communication Test is used to test the I
2
C communication
port between the DVD module and the microprocessor of the set.
where: xx is the 5DTC software version
yyy is the Backend (DVD) application software
version
zz.zz.zz is the Basic Engine (Servo) software version
9
Button pressed?
N
Y
DISC
Button pressed?
DVD SERVICE
TEST
Y
N9
Button pressed?
Display shows
"DVD SERVICE"
Note:
1. Remote Control must be in DVD source before start of any DVD Service Test.
2. All buttons on this "DVD SERVICE" test refers to the buttons on the Remote control.
3. Awaits for the mechanism to initialized before performing DVD test.
DVD SVC MENU
To start service test program
hold DISC1 & STANDBY-ON
buttons depressed while
plugging in the mains cord*
Display shows the
ROM version
"S-Vyy"
(Main menu)
S refers to Service Mode
V refers to Version
yy refers to Software version number of the uProcessor
(counting up from 01 to 99)
SERVICE TEST PROGRAM II
MAIN MENU
5DTC MX.. Range Service Test Program dd wk0302
* Hold till the Display is shown

3-3
Procedure for check Software version
1) Select Disc with the Remote Control
2) Press <SYSTEM MENU>
3) Use the down key move all the way down (4x) to
bottom of "Setup Menu".
4) Use the right key move to the sub-menu.
5) Use the down key move down (3x) to "Help text" and
down one more time to see the software version.
6) The TV screen will shows:
..... 5.1.10 030807P22204208 7.10.0 7.2
where 5.1.10 = Backend (DVD) software version
030807 = date of Backend software
22204208 = DVD version matrix
7.10.0 = Basic Engine (Servo) software version
7.2 = 5DTC software version
7) Press <OK> three times to exit.
Procedure to upgrade software
1) Power up the set and open tray Disc 1.
2) Place upgrade CD-ROM onto tray and close.
3) The set will display "DOWNLOAD" and the TV screen
will go blank.
4) The TV screen turns on again and Tray Disc 1 will
open.
5) Remove the upgrade CD-ROM and unplug the Mains
supply.
6) The whole process should last less than 10 minutes.
Caution:
This information is confidential and may not be distributed. Only a qualified service person
should reprogram the mono BE board.
After replacement/repair of the Mono BE board, the customer settings and also the region code may be lost.
Reprogramming will put the set back in the state in which it has left the factory, i.e. with the default settings
and the allowed region code.
Reprogramming will be done by way of the Remote Control.
Put the player in stop mode, Disc 1 with no disc loaded.
Do the following steps with the Remote Control:
1) Press <DISC MENU> followed by numerical keys <1> <5> <9>
The set display shows: - 0 - 0 - 0 - 0 -
2) Press now successively the following numerical keys :
for MX5800SA/21R : <3><2><3> <0><4><0> <0><8> AP
for MX5800SA/21S : <4><2><3> <0><4><0> <0><8> Australia, New Zealand
for MX5800SA/22S : <2><2><2> <0><4><2> <0><8> Europe
for MX5800SA/33S : <3><2><3> <0><4><1> <0><8> AP - Korea
for MX5800SA/35S : <6><2><3> <0><4><0> <0><8> China
for MX5800SA/78 : <3><2><3> <0><4><1> <0><8> Latam
for MX5900SA/37 : <1><1><1> <0><4><3> <0><8> US
3) Press <DISC MENU> again. The set display will show: DONE .
Caution: The set needs about 3 seconds to reset to required setting.
4) Disconnect mains to ensure proper reset.
Reprogramming of DVD version matrix

4-1 4-1
SET BLOCK DIAGRAM
1/2XTDA8920
LPS COIL
MAINS TRAFO
SURROUND
1/2XTDA8920
TDA8920
L/R
TDA8920
POWER AMP
DVD Modul
Pow r Amplifi r
Front Display
POWER AMP
Mains and R gulator
ECO 6
TMP88CU74F
ECO Standby
MX3900D_130_wk302-2
Not : All oth rs ar in th AV board.

4-2
MAIN WIRING DIAGRAM
4-2
1
for CO S T ONLY
40P
AD
PCMCIA
DIG_IN_2
AD
1
16
1
DTC
AD
18
GND_V
Prefold AD
4P 340mm (non K’ok)
GND_SUB
FRONT CONTROL
GND_C
400mm
1
GND_L
10P 280mm (MX39/55/56)
180mm
MX55/56/58/59
8P
H
1
10P
1
13
22
DVD_SC
GND_Sc
GND_a
1
280mm
FFC
DVD_SUB
180mm
1
BD
for MX5800SA
1
1
180mm
F
AV
1
13P 220mm (MX58)
40P
1
R_Pr
GND_V
for CO S T ONLY
AD
FLT
FLT
AD
40P
BD
Prefold
Prefold
GND_MIC
DVD Modul
MX58/59
MX39/55/56
8P 340mm (K’ok)
for MX39/55/56/58/59
1
Mute_AV
1
POWER MODULE
BD
HDPH & MIC
GND_a
GND_R
Prefold
Prefold
CVBS
FRONT DISPLAY
16P/18P(K’ok) 180mm (MX39/55/56)
4P
MX39/55/56/59
for MX3900D
K’ok
Prefold
Prefold AD
Prefold AD
for MX5500/5600
DVD_R
340mm
4P 220mm (MX39/55/56)
2P
F
1
AD Prefold
240mm
DVD_Ls
GND_S
DVD_C
POWER SWITCH
MX5800SA
DPL2_L
TUNER
10P
10P
5P
AD
120mm
400mm
17P
MIC_IN
DVD_L
1
AD
AD
180mm
FMN
GND_d
1
GND_V
Y_G_Y
10
13P
DPL2_R
SCART 0
13P
14P 220mm (MX58)
100mm
7P
1
DIG_IN_1
22P 220mm (MX58)
KEY
140mm
for MX55/56/58/59
C_B_Pb
for i6000
for MX39/55/56/58/59 for i6000
GND_V
Y
GND_V
C
14
for MX3900D
16P 220mm (MX59)
GND_S
DIG_OUT
1
MX3900D
DVD_Rs
220mm
GND_V
MX39/55/56
8P 220mm (MX58/59)
MX58/59
1
H
13P 180mm (MX39/55/56)
1
(MX58/59) (MX58/59)
(MX58/59)
(MX58/59)
R f r to pag 4-3 for d tails
R f r to pag 4-4
for d tails

1
2
3
4
L
SUB-WOOF R
SUR L
5
6
10
Amplifi r
1
1
1
1
SUB-WOOF R_R
C NT R
SUR R
SUB-WOOF R_L
1
1
75W 7-CHANNEL
1
2
3
4
10
1
6-CHANNEL
1
1
1
1
1
5
6
7
8
9
1
H 10P 280mm
H 6P
SUB-WOOF R_R
SUB-WOOF R_L
1
1
1
7
8
9
10
11
12
3
4R
SUR L
1
1
1
SPK I
SPK II
SPK II
1
1
1
1
120mm
H 4P 120mm
1
2
BD
180mm
10P
Prefold
BD
180mm
220mm
10P
Prefold
120mm
H 4P
120mm
H 4P
120mm
H 4P
SPK I
H 4P 220mm
H 5P
10P
Prefold
BD
120mm
H 9P
120mm
1
120mm
H 8P
140mm
H 5P
180mm
1
100W
5
6
7
8
9
3104 213 3525
75W
H 8P
R
L
C NT R
SUR R
Amplifi r
1
1
1
3104 213 3525
1
NOTE :
75W 6-CHANNEL : 1 X CLASS-D AMPLIFIER + SPK I
75W 7-CHANNEL : 1 X CLASS-D AMPLIFIER + SPK I + SPK II
100W : 2 X CLASS-D AMPLIFIER + SPK I + SPK II
H
240mm
4P
Blue/Yellow
1
Red/Black
SUPPLY
1 TRAFO
1
1
MAINS
VH 3X
150mm
VH 3X
150mm
5P
AD
120mm
and
ECO STBY
1
AD
180mm
10P
H
220mm
1
FAN
1
WIRING DIAGRAM - POWER MODULE DETAILS
4-3 4-3

V
Side FMN 1104
1
**
Side FMN 1106
10_6_12
mute_av
V
DVD_R
FOLD
8X 340mm BD
FOLD
(0.5MM)
11X 220mm BD
GND_A
1+3V3_S NS
+3V3
+3V3
d
GND
blue_u
V
red_v
GND_B d dig_out dig_in_1 dig_in_2 GND_C GND_A
DVD_L
GND_A
Side FMN 1203
1
1
1
24X 220mm BD
1
DVD_LF DVD_LS GND_B DVD_C GND_C DVD_RS GND_B d dig_out
STOKO WIR
11X 340mm BD
GND_C GND_A mic_gnd mic_in GND_A GND_A DPL_L DPL_R
DVD_L
Side FMN 1202 / 1203
1
Y
GND
GND
GND
Side F 1112
*
Pb/Cb
Pr/Cr
(1.25MM)
GND_C DVD_RS
1
1
GND
SDA
1800
DSD_R
GND
GND
DSD_L
5DTC M chanism
DAC
1
dig_in_1 dig_in_2
1
PSCAN
*
*
**
1
8X 220mm BD
30X 100mm BD
Pb/Cb
Pr/Cr
Side FMN 1000
*
Side F 1002
SCL
GND
120mm BD
1
MUT _DVD
1
8035
GND
Y
GND
YC4 +3V3 YC5 YC6 GND +3.3V
GND YC7 GND
24x
GND
HSYNC 27MHZ CLK GND YC0 GND YC1 GND YC2 GND GND ODD/ V N YC4 +3V3 YC5 YC6 GND +3.3V
GND YC7
+5V
+12V
GND
PCMSCLK(NC)
PCMDATA0(NC)
GND
PCMCLK (NC)
PCMLRCLK(NC)
GND
SPDIF
PCMDATA0(NC)
+12V
I2C_CLK_DVD
1
1
1
1704
SDA SCL HSYNC
GND
GND
YC0 GND YC1 GND YC2 GND YC3 +5V GND ODD/ V N
WORK_CLK/S L_DSD
GND
BIT_CLK/DSD_CLK
GND
256FS
GND
SCL-DAC
SDA-DAC
GND
DSD_PCM8 (NC)
SCL-DAC
DSD_PCM9(NC)
INT_R Q
DAC_RST
CLK_S L
I2C_DATA_DVD
SCART1
B_R F
G_R F
G_Y
YC3 +5V
Y_R F
Y
C_R F
C
CVBS_R F
CVBS
B_U
SCART0
+3V3
+3V3
DSD_PCM9
P50/GPIO2(NC)
GPIO3
GPIO1(NC)
+3V3 +3V3 +5V +12V GND
PCMSCLK(NC)
SACHI 5.0
GND
PCMCLK (NC) PCMLRCLK
GND
SPDIF MUT +12V
I2C_CLK_DVD
GND
27MHZ CLK GND
DSD_LF
GND
DSD_C NTR
GND
DSD_Rs
GND
DSD_Ls
GND
DSD_L
GND
DVD_LF
GND
384FS
GND
DSD_LF
GND
DSD_C NTR
GND
DSD_Rs
GND
DSD_Ls
SDA-DAC
GND
I2C_DATA_DVD SCART1 B_R F G_R F G_Y R_R F R_V
R_R F
R_V
C_R F C CVBS_R F CVBS B_U SCART0
1
DSD_PCM8 (NC)
GND
TO AV BOARD Conn 1404
Side FMN 1107
Side FMN 1105
DVD_C
30X 140mm BD
1
384FS
GND
TO AV BOARD
GND_B
TO AV BOARD
DVD_LS
TO FRONT
PCB
8X 180mm BD
***
180mm
d
d
+5V
DVD_R
GND
DSD_L
GND
WORK_CLK/S L_DSD
GND
BIT_CLK/DSD_CLK
GND
256FS
GND
Y_R F Y
For MX5800/5900 only
NOTE :
ALL WIR AR 1MM PITCH, UNL SS OTH RWIS STAT D BY (XXX). FOR S T WITH PROGR SSIV
SCAN ONLY
** :
FOR S T WITHOUT DPLII
* : *** :
FOR S T WITH KARAOK
Conn 1242
Conn 1406
Conn 1104
5DTC Modul
Control
Board
HF Buffer Board
WIRING DIAGRAM - DVD MODULE DETAILS & P-SCAN BOARD
4-4 4-4

TECHNICAL REMARKS
P-SCAN BOARD
TABLE OF CONTENTS
Top View Layout.......................................................................5-2
Bottom View Layout..................................................................5-3
Circuit Diagram Part 1)...........................................................5-4
Circuit Diagram Part 2)...........................................................5-5
Electrical parts list....................................................................5-6
5-1 5-1

5-2 5-2
P-SCAN BOARD - TOP VIEW LAYOUT
This assembly drawing shows a summary of all possible versions. For components used in a specific version see schematic diagram and respective parts list.
3139 113 3516 pt2 dd wk0315

5-3 5-3
P-SCAN BOARD - BOTTOM VIEW LAYOUT
This assembly drawing shows a summary of all possible versions. For components used in a specific version see schematic diagram and respective parts list.
3139 113 3516 pt2 dd wk0315

5-4 5-4
P-SCAN BOARD - CIRCUIT DIAGRAM (PART 1)
VSSQ VSS
LATCH
REFRESH
COUNTER
BANK0
ROW-
ADDR
LATCH &
DECODER
COLUMN
DEDCODER
BANK0
MEMORY
ARRAY
4,096x256x16)
SENSE AMPLIFIERS
COMMAND
DECODE
CTRL
LOGIC
MODE REG
ADDRESS REGISTER
ROW
ADDR
MUX
LOGIC
CTRL
NC
VDD
DQM0...3
VDDQ
DATA INPUT REGISTER DATA OUTPUT REGISTER
READ DATA LATCH
WRITE DRIVERS
I/O GATING
DQM DATA LOGIC
ADDR
COUNTER/
BANK
COLUMN
DC voltage measured in STOP-MODE
F
G
H
I
2100 A14
2101 A5
2102 A12
2103 A14
2104 A13
2105 B
210 A5
2107 B14
2108 A
2109 B5
2110 A7
2111 A
2112 A
2113 B8
2114 A5
2115 A5
211 A
2117 B8
2118 A5
For MX5900SA/37 only
1 2 3 4 5 7 8 9 10 11 12 13 14
1 2 3 4 5 7 8 9 10 11 12 13 14
A
B
C
D
E
F
G
H
I
A
B
C
D
E
P-scan_LineDoubler
DECOUPLING CAP FOR FLI2301
2119 A
2120 B8
2121 B8
2122 A8
2123 A8
2124 A8
2125 A8
212 A9
2127 A9
2128 A9
2129 A9
2130 B12
2131 B12
2132 B12
2133 B13
2134 B10
2135 B10
213 B10
2137 B9
2138 A9
2139 B9
2140 B13
2141 B13
2142 C13
2143 C13
2144 C13
2145 C12
214 C12
2147 C13
DECOUPLING CAP FOR FLI2301
2148 B10
2149 B10
2151 C8
2152 B8
2170 I1
3100 B4
3101 B5
3102 B5
3103 C2
DECOUPLING CAP FOR FLI2301
3104 D2
3105 F1
310 F1
3107 G1
3108 G1
3109 G1
3110 G1
3111 G1
3112 I3
#
3113 I3
3114 I3
3115 I4
311 I3
3117 I3
3118 I4
3119 I3
3120 I4
3121 I4
3122 I4
3123 I4
3124 I4
3125 I4
312 I5
3127 I4
3128 I5
3129 I4
DECOUPLING CAP FOR FLI2301
3130 I5
3131 I5
3132 I5
3133 I5
3134 I5
3135 I5
313 I5
3137 I5
3138 I5
3139 I5
3140 I7
3141 I
3142 I
3143 I
3144 I
3145 I
314 I
22R
*
*
3147 I7
3148 I
3149 I
3150 C7
3158 I7
3159 I7
31 0 D11
31 1 D11
31 2 D11
31 3 E11
#
*
I
3170 H1
4100 F2
4101 F2
4103 C8
4105 B4
4110 A13
5100 A13
5101 A13
5102 A13
7100 C3
7101 C12
7103 A12
220n 2142
220n 2132
100n 2120
3149
22R
22R
3109
2105
100n
3115
22R
3144
100n 2113
3106
2118 100n
2102
47u
10K
22R3141
3119 22R
2121 100n
100n 2124
3160 22R
22R3127
100n 2125
22R
3123 22R 3135 22R 3122 3129 22R
3105 10K
100n 2134
22R3133
3159 22R
22R
100n
2152
3158
4103
2151
100n
220n
3104 22R
LD1117
GND
1
IN
32
OUT
2146
2129 100n
7103
5102
2130 220n
2103
47u
10u
22R3117
2133 220n
27R
3102
3126 22R
3100
10R
100n 2116
22R
2135 100n
3137
100n 2148
2140 220n
3136
22R3124 22R
220n
4100
2137 100n
2141
2138 100n 100n 2126 100n 2127
GND_PS
GNDEARTH
22R3111
2108
22R3128
10u
3120 22R 3145 22R
3162
3134 22R
22R
2123 100n
150R
3108 100R
3101
100n 2114 100n 2111 2119 100n
220n 2144 220n 2147
22R3140 22R3130
2115 100n
GNDEARTH
3150
4K7
VSS16 194 VSS17 198
17 VSS2
VSS3
31
VSS4
37
49 VSS5
VSS6
63
VSS7
69
VSS8
81
VSS9
89
VSYNC1_PORT1
2
VSYNC2_PORT1
6
VSYNC_PORT2 207
191
XTAL_IN
XTAL_OUT 192
VDD9 193
VDDcore1
16
36 VDDcore2
VDDcore3
68
VDDcore4
80
VDDcore5
96
VDDcore6 123
VDDcore7 138
VDDcore8 197
VSS1
9
VSS10
97
VSS11 113
VSS12 124
129
VSS13
VSS14 139
VSS15 147
104
TEST0 188
189
TEST1 TEST2 190
115
TEST3
TEST_IN
90
TEST_OUT0 116
TEST_OUT1 117
VDD1
8
VDD2
30
VDD3
48
VDD4
62
VDD5
88
VDD6 112
VDD7 128
VDD8 146
82 83 SDRAM_DATA27
SDRAM_DATA28
84 85 SDRAM_DATA29
SDRAM_DATA3
53
SDRAM_DATA30
86 SDRAM_DATA31 87
SDRAM_DATA4
54 55 SDRAM_DATA5
SDRAM_DATA6
56 SDRAM_DATA7 57 SDRAM_DATA8 58 SDRAM_DATA9 59
SDRAM_DQM 110
SDRAM_RASN 105
SDRAM_WEN
64 SDRAM_DATA12
SDRAM_DATA13
65 66 SDRAM_DATA14
SDRAM_DATA15
67
SDRAM_DATA16
70 SDRAM_DATA17 71 SDRAM_DATA18 72 73 SDRAM_DATA19
SDRAM_DATA2
52
SDRAM_DATA20
74 SDRAM_DATA21 75 SDRAM_DATA22 76 SDRAM_DATA23 77 SDRAM_DATA24 78 SDRAM_DATA25 79
SDRAM_DATA26 SDRAM_ADDR4
99 98 SDRAM_ADDR5 95 SDRAM_ADDR6
SDRAM_ADDR7
94
SDRAM_ADDR8
93
SDRAM_ADDR9
92
SDRAM_BA0 108
107
SDRAM_BA1
SDRAM_CASN 106
114
SDRAM_CLKIN
SDRAM_CLKOUT 111
SDRAM_CSN 109
SDRAM_DATA0
50
SDRAM_DATA1
51
SDRAM_DATA10
60 SDRAM_DATA11 61
R|Cr|CrCb_5
38
R|Cr|CrCb_6
39
R|Cr|CrCb_7
40
R|V|PR_OUT_2 140
141
R|V|PR_OUT_3
R|V|PR_OUT_4 142
R|V|PR_OUT_5 143
144
R|V|PR_OUT_6
R|V|PR_OUT_7 145
SCLK
45
SDATA
46
SDRAM_ADDR0
103
SDRAM_ADDR1
102
SDRAM_ADDR10
91
SDRAM_ADDR2
101
SDRAM_ADDR3
100
HSYNC2_PORT1
5
HSYNC_PORT2 208
4IN_CLK1_PORT1
IN_CLK2_PORT1
10
IN_SEL
41
OE 156
PLL_PVDD 157
PLL_PVSS 158
RESET_N
47
R|Cr|CrCb_0
29
32 R|Cr|CrCb_1
R|Cr|CrCb_2
33
R|Cr|CrCb_3
34
35 R|Cr|CrCb_4
G|Y|Y_1
22
G|Y|Y_2
23
24 G|Y|Y_3
G|Y|Y_4
25
G|Y|Y_5
26
27 G|Y|Y_6
G|Y|Y_7
28
G|Y|Y|Y_OUT_0 148
G|Y|Y|Y_OUT_1 149
G|Y|Y|Y_OUT_2 150
G|Y|Y|Y_OUT_3 151
G|Y|Y|Y_OUT_4 152
G|Y|Y|Y_OUT_5 153
154
G|Y|Y|Y_OUT_6
G|Y|Y|Y_OUT_7 155
HSYNC1_PORT1
1
DAC_GR_AVSS 185
DAC_PVDD 187
DAC_PVSS 167
DAC_ROUT 176
DAC_RSET 180
168
DAC_VDD
DAC_VREFIN 182
DAC_VREFOUT 181
DAC_VSS 169
DEV_ADDR0
44 DEV_ADDR1
43
FIELD_ID1_PORT1
3
FIELD_ID2_PORT1
7
FIELD_ID_PORT2 206
42 FILM_SYNC_IN
G|Y|Y_0
21
D1_IN_4 202 D1_IN_5 203 D1_IN_6 204
205
D1_IN_7
183
DAC_AVDD
171
DAC_AVDDB
DAC_AVDDG 174
DAC_AVDDR 177
DAC_AVSS 184
DAC_AVSSB 172
DAC_AVSSG 175
DAC_AVSSR 178
DAC_BOUT 170
DAC_COMP 179
DAC_GOUT 173
DAC_GR_AVDD 186
B|U|Pb|C_OUT_5 133
B|U|Pb|C_OUT_6 134
B|U|Pb|C_OUT_7 135
136
B|U|Pb|C_OUT_8
B|U|Pb|C_OUT_9 137
CLKOUT 125
CLK_PORT2 195
CTLOUT0 118
CTLOUT1 119
CTLOUT2 120
CTLOUT3 121
CTLOUT4 122
196
D1_IN_0 D1_IN_1 199 D1_IN_2 200 D1_IN_3 201
AVSSPLL_SDI 163
159
AVSS_PLL_BE1 AVSS_PLL_BE2 162
B|Cb|D1_0
11
B|Cb|D1_1
12
B|Cb|D1_2
13
B|Cb|D1_3
14
15 B|Cb|D1_4
B|Cb|D1_5
18
B|Cb|D1_6
19
20 B|Cb|D1_7
126
B|U|Pb|C_OUT_0
B|U|Pb|C_OUT_1 127
B|U|Pb|C_OUT_2 130
B|U|Pb|C_OUT_3 131
B|U|Pb|C_OUT_4 132
7100
FLI2301
AVDDPLL_FE 165
AVDDPLL_SDI 164
AVDD_PLL_BE1 160 AVDD_PLL_BE2 161
AVSSPLL_FE 166
100n
2106
100n 2109
22R3110
22R3116
2136 100n 100n 2117
3142 22R 3113 22R
10u
220n 2131
GND_PS
5100
22R3112 22R
2128 100n
3147 22R 3146
GND_PS
GND_PS
2112 100n
3121
100n 2139
22R
3114 22R
2149 100n
3139 22R 3132 22R
3107 100R
2122 100n
4101
22R3131 22R3138 22R3118
22R
3103
10u
5101
22R3143
220n 2143
2107
47u
2100
2145
47u
6 12323846527884
17 WE_
220n
15294339354149557581
44 58 72 86
DQ7
74DQ8
76DQ9
DQM0 16
DQM1 71
DQM2 28
DQM3 59
14
21
30
57
69
70
73
19 RAS_
1
DQ20
39DQ21
40DQ22
42DQ23
45DQ24
47DQ25
48DQ26
DQ27 50
51DQ28
53DQ29
7DQ3
54DQ30
56DQ31
8DQ4
10DQ5
DQ6 11
13
CKE
68 CLK
20 CS_
2DQ0
4DQ1
77DQ10
79DQ11
DQ12 80
82DQ13
83DQ14
85DQ15
31DQ16
33DQ17
34DQ18
36DQ19
DQ2 5
37
25 A0
26 A1
24 A10
27 A2
60 A3
A461
62 A5
63 A6
64 A7
65 A8
66 A9
22 BA0
23 BA1
CAS_18
67
MT48LC2M32B2TG
7101
3125 22R
22R3148
2110 100n
3163 22R
2170
4u7
22R3161
2101
4105
GND_PS
100n
4110
2104
1u
YB 5)
YB 6)
YB 7)
+3V3_D
RESET
+3V3_D
+1V8_SCAN +1V8_CORE
3170
4K7
DATA 24)
DATA 25)
DATA 26)
DATA 27)
DATA 28)
DATA 29)
DATA 30)
DATA 31)
SRAM_DQM
27M_CLK
27M_CLK
27M_CLK
+3V3_SCAN
YB 0)
YB 1)
YB 2)
YB 3)
YB 4)
ADD 7)
ADD 6)
ADD 5)
ADD 4)
ADD 3)
ADD 2)
ADD 1)
ADD 0)
DATA 0)
DATA 1)
DATA 2)
DATA 3)
DATA 4)
DATA 5)
DATA 6)
DATA 7)
DATA 8)
DATA 9)
DATA 10)
DATA 11)
DATA 12)
DATA 13)
DATA 14)
DATA 15)
DATA 16)
DATA 17)
DATA 18)
DATA 19)
DATA 20)
DATA 21)
DATA 22)
DATA 23)
+1V8_PLL +3V3_DAC
SCL_3V3
SDA_3V3
+1V8_CORE
+3V3_D
+3V3_DAC
+3V3_D
+3V3_MEM
+3V3_MEM
+1V8_PLL
+1V8_DAC
WEN
CLK
CSN
CASN
RASN
BA0
BA1
ADD 10)
ADD 9)
ADD 8)
DATA 15) DATA 16) DATA 17) DATA 18) DATA 19) DATA 20) DATA 21) DATA 22) DATA 23) DATA 24) DATA 25) DATA 26) DATA 27) DATA 28) DATA 29) DATA 30) DATA 31) ADD 10) ADD 9) ADD 8) ADD 7) ADD 6) ADD 5) ADD 4) ADD 3) ADD 2) ADD 1) ADD 0)
+3V3_D
+3V3_D
+1V8_CORE
HSYNC
RESET
BA0
BA1
CASN
RASN
+3V3_D
+3V3_D
+3V3_D
+3V3_D
+1V8_CORE
+1V8_CORE
+1V8_CORE
VSYNC
DATA 0)
DATA 1)
DATA 2)
DATA 3) DATA 4) DATA 5) DATA 6) DATA 7) DATA 8) DATA 9) DATA 10) DATA 11) DATA 12) DATA 13) DATA 14)
CLK
CLK
CSN
SRAM_DQM
WEN
+1V8_PLL
YB 0) YB 1) YB 2) YB 3) YB 4) YB 5) YB 6) YB 7)
Pr
Y
Pb
+1V8_DAC
VSYNC_MONO
8239_210_95352 for 3516 pt2 dd wk0315
Note : Some values may varies, see respective parts list for correct value.
: Provision
*