Philips Home power SRP4519L/27 User manual

User manual
v1 05/20
Home power
SRP4519L/27

2
Introduction ....................................................... 2
Setup .................................................................. 3
Button Functions............................................... 4
Programming Your Remote ..............................6
Direct Code Entry.........................................6
Auto Code Search......................................... 7
Controlling Combo Devices.........................9
Using Your Remote.......................................... 10
Primary Audio Control ............................... 10
Code Identication...................................... 11
Reset to Factory Settings........................... 11
Troubleshooting ...............................................12
Warranty............................................................13
FCC Statement ................................................ 14
Congratulations on your purchase of this
Philips Universal Replacement Remote
Control. Designed primarily for LG
devices, this universal remote includes
preprogrammed buttons that allow you to
immediately control your LG equipment.
For example, the device buttons (TV, B-RAY
and AUD) are preprogrammed to control a
corresponding LG TV, sound bar or Blu-ray™/
DVD player. LG-specic function keys (HOME,
MY APPS, Q. MENU, etc.) are preprogrammed
for full functionality and navigation of your
LG devices. Additionally, this remote is
preprogrammed for Roku boxes, using the
STRM button, compatible with all major
brands and capable of operating thousands
of audio/video devices that complete your
home theater setup.
Table of Contents
For remote control help:
byjasco.com/50232i

3
Your universal remote requires two (2) AAA
batteries (not included). Alkaline batteries
are recommended.
Battery Installation
1. On the back of the remote, pull down on
the textured surface and slide battery
cover downward to remove.
2. Match the (+) and (-) marks on the
batteries to the (+) and (-) marks inside
the battery compartment, then insert two
(2) AAA batteries. Be sure to use fresh
batteries.
3. Position battery cover slightly below
opening and push upward to lock into
place.
NOTE:If your remote stops operating properly,
replace the batteries with new ones.
Battery Precautions
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-
zinc), or rechargeable (Ni-Cd, Ni-MH, etc.)
batteries.
• Always remove old, weak or worn-out
batteries promptly and recycle or dispose
of them in accordance with local and
national regulations.
Battery Saver
Your remote automatically turns o if the
buttons are held down for more than 8
seconds. This will save your batteries should
your remote get stuck in a place where the
buttons remain depressed (e.g., between
sofa cushions).
Code Saver
You have up to 10 minutes to change the
batteries in your remote without losing the
codes you have programmed.
Setup

4
Button Functions
21
23
25
19
13
7
11
1
9
15
4
2
816
814
818
9 20
9 22
9 24
9 26
12
8
6
10
17
27
3
5

5
Button Functions
1. Power - Turns devices ON/OFF
2. Input - Selects video inputs
3. TV, STRM, B-RAY, AUD - Selects the device to control
4. Record, play, stop, rewind, fast forward, pause
5. Programmable Favorites - Program up to 10
favorite channels for quick access
6. Closed caption - Selects closed caption options
7. DVD/Blu-ray™open/close - Open/close a player,
or List features on cable/satellite receivers
8. Setup - Used to program the remote
9. Info - Displays on-screen show/content information
10. My Apps - Shows the list of apps available
(Smart TV's only).
11. Mute - Mutes sound
12. Channel up/down
13. Volume up/down
14. Ratio - Resizes the screen
15. Last channel - Returns to the previously
selected channel
16. Home - Easily access features on streaming
devices
17. Menu - Displays the on-screen menu
18. Q. Menu - Opens a list of quick menu options
for your frequently used functions
19. Up/down/left/right menu navigation
20. Ok - Selects menu items for the controlled device
21. Back - Returns to previous screen
22. Exit -Exit on-screen menus
23. Guide - For use with cable/satellite receivers
24. ABCD - Access additional features for DVRs,
cable and satellite receivers
25. Numbers - Enter numbers for direct channel selection
26. Enter - Some devices require enter to be
pressed after channel selection
27. Dash (-) - Use to select digital channels, e.g., 4-1

6
Programming Your Remote
Your remote is designed to control multiple
audio/video devices. To use, you will need to
program the remote for your devices. There
are two dierent methods you can use to
program the remote, Direct Code Entry or
Auto Code Search.
• The Direct Code Entry method is the
recommended method, as it is the simplest
and quickest method in most cases.
• The Auto Code Search method searches
through all the codes in the remote to nd
a code for your device.
NOTE:This remote comes preprogrammed for
Roku
®
boxes and LG devices. Press TV, B-RAY and
AUD for LG devices, and STRM for Roku boxes.
Direct Code Entry (Recommended)
1. Locate the Code List included
with your remote. Find the
section for the type of device
you wish to control, (e.g., TV,
STRM, DVD, AUD, CBL, AUX).
Locate the brand of your device
and circle all the remote codes
for the brand.
2. Press and hold down the SETUP
button on the remote until the
red light on the remote control
turns on. Release the SETUP
button. The red light will
remain on.
NOTE:The red light will either
be a small light at the top of the
remote or the power ON/OFF
button.
3. Press and release the device
button on the remote for the
type of device you wish to
control, (e.g., TV, STRM, B-RAY,
AUD). The red light will blink
once and remain on.
NOTE:Any of the device buttons
on the remote can be programmed
to control any of your devices. For
example, you can use the AUD
device button on the remote to

7
Programming Your Remote
control a satellite receiver, digital
converter box, streaming media
player or any device category in
the Code List.
4. Use the number buttons on the
remote to enter the rst 4-digit
remote code you circled in the
Code List in Step 1. The red light
will turn o after entering the
fourth digit.
5. Point the remote at the device.
Test the buttons on the remote
to see if the device responds as
you would expect. If the buttons
do not operate the device,
return to Step 2 above and use
the next code that you circled
for that device.
6. Repeat steps 1 – 5 for each
device you wish to control.
Programming Notes
• Some codes may operate only a few
functions of your device. There may
be another code in the Code List that
controls more functions. Test other codes
in the Code List for more functionality.
• If you do not nd a remote code that
works your device or there are no codes
in the Code List for your device, use the
Auto Code Search method in the next
section to program your remote.
• For combination devices such as a TV/
DVD combo or TV/VCR combo, you may
have to enter a code for each device.
• Write down the remote codes used to
program the remote for future reference.
Auto Code Search
Auto Code Search is a process where you can
search through all the codes stored in the
remote to nd a code for your device. It is
recommended that you read through all the
steps below to familiarize yourself with Auto
Code Search before starting the process.

8
Programming Your Remote
1. Manually turn on the device you
wish to control.
NOTE:The Auto Code Search
process cannot be used for devices
without power ON/OFF capability.
Use the Direct Code Entry method in
these cases.
2. Press and hold down the SETUP
button on the remote until the red
light on the remote control turns
on. Release the SETUP button.
The red light will remain on.
NOTE:The red light will either be a
small light at the top of the remote
or the power ON/OFF button.
3. Press and release the device
button on the remote for the type
of device you wish to control, (e.g.,
TV, STRM, B-RAY, AUD). The red
light will blink once and remain on.
4. With the remote pointed at the
device, press and release the
POWER button on the remote.
The remote will send 10 dierent
codes to the device. The red light
will blink once for each code and
remain on after sending the 10
codes.
Did the device turn o?
• If YES, go to Step 5.
• If NO, repeat Step 4 to test the
next 10 codes.
5. Manually turn the device back on.
6. With the remote pointed at the
device, press and release the
VOL button. The remote will re-
send the rst code of the 10 codes
from Step 4. The red light will blink
once and remain on.
Did the device turn o?
• If YES, you have found a code
for the device. Press and
release the same device button
you pressed in Step 3. This will

9
Programming Your Remote
store the code in the remote.
Go to Step 7.
• If NO, continue to press and
release the VOL button
until the device turns o
to test the other 9 codes
from Step 4. Be sure to wait
approximately 3 seconds after
each VOL button press
to allow the device time to
respond to the code. When
the device turns o, you have
found a code for your device.
Press and release the same
device button pressed in Step
3. This will store the code in
the remote. Go to Step 7.
NOTE:
• The VOL button can be used
to go backwards through each
batch of 10 codes.
• The red indicator light will ash
2 times after testing the rst or
last code in each batch of 10.
7. Use the remote to turn the
device back on. Test the buttons
on the remote to see if the
device responds as you would
expect. If the buttons do not
operate the device, return to
Step 2 and repeat this process
to search for a better code to
operate the device.
8. Repeat this process for each
device you wish to control.
Controlling Combo Devices
Some combo devices (e.g. TV/VCR, TV/DVD,
DVD/VCR, etc.) will require you to set up
two dierent device buttons to control both
parts of the combo device. For example, if
you have a TV/DVD combo, you may need
to set up one code under the TV button to
control the TV and a separate code under
the DVD button to control the DVD.

10
Using Your Remote
Primary Audio Control
The Primary Audio Control feature allows
you to select a single device that the volume
buttons always control. For example, the
remote can be in TV mode while the volume
buttons control the volume on your audio
receiver or sound bar instead of your TV.
Enabling Primary Audio Control
1. Press and hold down the SETUP
button on the remote until the
red light on the remote control
turns on. Release the SETUP
button. The red light will
remain on.
2. Press and release the device
button (TV, AUD, etc.) on the
remote for the device you wish
to control the volume.
3. Press and release the
MUTE button.
4. Press and release the VOL
button. The red light will blink
twice and turn o.
Disabling Primary Audio Control
1. Press and hold down the SETUP
button on the remote until the
red light on the remote control
turns on. Release the SETUP
button. The red light will
remain on.
2. Press and release the device
button (TV, AUD, etc.)
programmed to control the
Primary Audio Control feature.
3. Press and release the
MUTE button.
4. Press and release the VOL
button. The red light will blink
twice and turn o.