Philips M455 Product information sheet

M450
M455
Register your product and get support at
www.philips.com/support
Short user manual
2Connect
Multi-handset version
only.
1 2 3
1Overview
In call
Enter the option menu.
Access the redial list.
Adjust the volume.
Recall (network dependent).
End calls.
Enter a pause (press and hold).
Turn the speaker on/off.
Mute/unmute the microphone.
In menu
Cancel / back
Up / down
Exit menu.
Standby
Access the main menu.
Access the redial list.
Phonebook
Call log
Make and receive calls.
Switchthe handset on/off (press and hold).
Make intercom call (press and hold).
Lock/unlock the keypad (press and hold).
Make and receive calls through the speaker.
/ M335 only:
Listen to new message from the answer
machine. / Access the answer machine menu.
In text input
Delete text.
Enter a space.
Switch upper/lower case.
Display icons
It displays the connection between the handset
and the base.The more bars are shown, the
better the signal strength is.
It remains steadily on when browsing incoming
calls in the call log.
It indicates an outgoing call in the redial list.
when browsing new missed calls. It remains
steadily on when browsing the missed calls in
call log that are already read.
steadily on during a call.
The speaker is on.
The ringer is off.
there is a new message or when the memory is
full. It remains steadily on when the telephone
answering machine is turned on.
messages, is steady for reviewed messages.
* This is network dependent
It is displayed when you scroll up/down a list or
increase and decrease the volume.
There are more digits on the right. Press to
read.
ECO+ The ECO+ mode is activated.
Find handset
Microphone
Earpiece
Loudspeaker
(back side)
Display icons
/ (M455)
M455
(M450)
Important safety instructions
Warning
• The Electrical network is classified as hazardous.
The only way to power down the charger is to
unplug the power supply from the electrical outlet.
Ensure that the electrical outlet is always easily
accessible.
• Refer to safety information before using the
product.
• Hereby, TP Vision Europe B.V. declares that this
product is in compliance with the essential
requirements and other relevant provisions of
Directive 2014/53/EU.
• Use only the power supply listed in the user
instructions.
• Use only the batteries listed in the user
instructions.
• Do not allow the product to come into contact
with liquids.
• Risk of explosion if battery is replaced by an
incorrect type.
• Dispose of used batteries according to the
instructions.
• When the handset rings or when the handsfree is
activated, keep the handset away from your ear to
avoid hearing damage.

This symbol on a product means that
the product is covered by European
Directive 2012/19/EU.
This product has been manufactured
by, and is sold under the responsibility
of Hong Kong Holding Limited and
Hong Kong Holding Limited . is the
relation to this product.
Philips and the Philips Shield Emblem
are registered trademarks of Koninklijke
Philips N.V. and are used under license
from Koninklijke Philips N.V.
UMS_M450/M455
01_EN_V1.0
Frequently
asked questions
No signal bar is displayed on the screen.
• The handset is out of range. Move it closer to the base
station.
• If the handset displays [Unregistered], register
your handset (see the section on “Register additional
handsets”).
If I fail to pair (register) the additional handsets to the
base station, what do I do?
Your base memory is full. Access > [Services] >
[Unregister] to unregister the unused handsets and
try again.
I have chosen a wrong language which I cannot read,
what do I do?
1 Press to go back to the standby screen.
2 Press to access the main menu screen.
3 The following options will appear on the screen:
[Phone setup] > [Language]
[Réglages] > [Langue]
[Telefon-Setup] > [Sprache]
> [Lingua]
4 Select them to access the language options.
5 Select your own language.
My handset is in searching status, what do I do?
• Make sure that the base station has power supply.
• Register the handset to the base station.
• Move the handset closer to the base station.
I cannot change the settings of my voice mail, what do Ido?
The voice mail service is managed by your service
provider but not the phone itself. Contact your service
provider to change the settings.
No display
• Make sure the batteries are charged.
• Make sure there are power and phone connections.
The handset on the charger does not charge.
• Make sure the batteries are inserted correctly.
• Make sure the handset is placed properly on the
once.
• Make sure thedocking tone setting is turned on.When
the handset is placed correctly on the charger, you can
hear a docking tone.
• The charging contacts are dirty. Disconnect the power
• Batteries are defective. Purchase new ones with the
Bad audio (crackles, echo, etc.)
• The handset is nearly out of range. Move it closer to
the base station.
• The phone receives interference from the nearby electrical
appliances. Move the base station away from them.
• The phone is at a location with thick walls. Move the
base away from them.
The handset does not ring.
Make sure the handset ringtone is turned on.
The caller ID does not display.
• The service is not activated. Check with your service
provider.
• The caller’s information is withheld or unavailable.
www.philips.com/support
To access the user instructions online, use the
reference model number written on the product
label at the bottom of the base station.
Technical data
Battery
• Philips: 2 x AAA NiMH 1.2 V Rechargeable
550 mAh batteries
Use only the supplied batteries.
Adapter (Base and charger):
Meic:
MN0063-E060040
HuaJin:
HJ-0600400P1-EU
Input: 100-240 V~
50/60 Hz 0.2A
100-240 V~
50/60 Hz 0.15A
Output: 6 V 0.4A 6 V 0.4A
Phonebook with 50 entries
Call log with 20 entries
Talk time: 16 hours
Standby time: 180 hoursRF output power: <24 dBm
Frequency Band: 1880 MHz ~ 1900 MHz
Note
•
prevent noise and caller ID problems caused by the
DSL interference.
•
www.p4c.philips.com.
4Enjoy
Phonebook
Add record
1 Press .
2 Select [Phonebook] > [Add new].
3 Follow on-screen instructions.
Call from the phonebook
1 Press .
2 Select a record and press .
Direct access memory
You have 2 direct access memories (Keys 1 and 2).
To dial the saved phone number automatically, press
and hold on the keys in standby mode.
Depending on your country, keys 1 and 2 are
preset to the voice mail number and information
service number of your service provider respectively.
(network dependent).
Call log
Call from the call log
1 Press .
2 Select a record and press .
View record
Press > > [View].
Save record
1 Press > > [Save number].
2 Follow on-screen instructions.
Delete record
1 Press > > [Delete].
2 Follow on-screen instructions.
Redial list
Call from the redial list
1 Press .
2 Select a record and press .
Save record
1 Press > > [Save number].
2 Follow on-screen instructions.
Delete record
1 Press > > [Delete].
2 Follow on-screen instructions.
Telephone answering machine
(for M455 only)
Record an announcement
1 Press > [Answ. Machine] >
[Announcement].
2 Follow on-screen instructions.
Listen to the incoming messages
Press > [Answ. Machine] > [Play].
Delete an incoming messages
1 When you listen to the message, press to
enter the options menu.
2 Select [Delete], then press
Register additional handsets
You can register additional handsets to the base
station.
1 Press .
2 Select [Services] > [Register], then press
3 Press and hold onthe base station for
10 seconds.
4 Enter the system PIN/passcode (0000).
5 Press
Registration is complete in less than 2 minutes.
Restore default settings
You can reset your phone settings to the original
factory settings.
1 Press .
2 Select [Services] > [Reset], then press to
3 Follow on-screen instructions.
Note
• You may recall the original PIN/passcode by
following this procedure.
3Get started
1 The batteries are pre-installed in the handset. Pull
the battery tape off from the battery door before
charging.
2
a welcome message (country dependent).
3 Set the country and language if prompted.
4 Set the date and time.
• If the time is in 12-hour format, press / to
select [am] or [pm] (country dependent).
Charge your phone
Charge 8 hours
> 70%
40% - 70%
10% - 40%
< 10%
Flashing: low battery
2021 © MMD Hong Kong Holding Limited.
All rights reserved. Specifcations are subject
to change without notice.
warrantor in