Philips AIB2211/97 User manual

User Manual
AIB2211/97

Directory
1. Important
2. Safety caution
3. Preparations before installation
4. Packing list
5. Installation steps
cations
7. About the the side button
8. About the remote controller
9. How to use
10. Maintenance
11. If a long idle period is expected
12. SIAA antibacterial certi cation instructions
13. Troubleshooting
14. List of environmental protection
15. Product Warranty Service Guide
01
02
07
09
10
13
14
15
16
18
20
21
22
24
25
Please read this installation instruction carefully and install this product correctly and safely.
Be sure to read pages 2 to 6 before installation (Safety Caution).
The manufacturer shall not be liable for any accident or injury caused by failure to install according

1. Important
Please read this instruction carefully before use.
- The product must be repaired by an authorized professional service personnel, otherwise
the manufacturer will not be responsible for the corresponding warranty.
- The power supply component is coupled with the machine. If the power supply component
is damaged, in order to avoid danger, it must be replaced by an authorized professional
personnel from the manufacturer, otherwise the manufacturer will not be responsible
for the corresponding warranty.
- The product is designed for domestic use, if it is used for commercial purposes,
the service life of this product will be shortened.
- Do not install in outdoor
users should stop using the product immediately and call the service hotline to report
a repair.
- Before any maintenance or cleaning of the product, please be sure to disconnect the
power supply.
-
service professional before use.
- Please do not cover the product with any object.
- Do not put heavy objects on the product.
-
The company has the right to interpret the above terms and conditions as permitted by law.
01

2. Safety Caution
- Before use, please read the following safety precautions carefully.
- Improper use of the product may cause serious accidents.
- The following content is closely related to safety, please be sure to strictly comply with
the requirements.
Warning: Refers to the contents that may cause serious personal safety or property damage.
Caution: Refers to the contents that may cause general personal safety or property damage.
1. or the
֭
2.
֭
3. For long time sitting, please adjust the sitting temperature to "normal temperature" gear.
֭
than "normal temperature" for a long time.
The power supply must be earthed with three-pin power plug.
֭ Otherwise it can be a cause of electrocution and so on.
WARNING
This symbol is used with the
above "Warning" and "Caution"
contents to draw your attention.
Please read it carefully and
strictly follow it.
Refers to something that
must not be performed.
This symbol indicates that
please refer to operation
instructions.
02

4. When inserting and unplugging the power plug, hold the plug body.
֭
the part of the wire.
5.
֭
6. The power plug should be fully inserted.
֭
7.
(such as the following) should adjust the temperature of the seat to normal temperature.
֭ Children
֭ The elderly
֭ The patient
֭ People who are unable to regulate their own temperature
֭
֭
֭ People who consumed too much alcohol
֭
֭
than "normal temperature" for a long time.
This picture is for
reference only
03

1.
2. -
- Do not replace the power plug or power cord by yourself.
- If the power supply cord is damaged, to avoid danger, it must be replaced by an
authorized service professional from the manufacturer.
֭
3. Do not scratch, damage, process, forcibly bend, stretch, tighten, bind, press, or shorten
the power cable.
֭
4.
֭
5. - Do not use voltage other than AC220V.
- Do not overload the circuit.
֭
6. Do not use water to clean the fuselage and power plug.
֭
PROHIBITION
220V
This picture is for
reference only
1. Please use the installation accessories delivered with the product (old hose assembly
cannot be reused).
֭
04

Do not remove or insert the power plug with wet hands.
֭ Otherwise it can be a cause of electrocution.
If the product is faulty, please immediately shut down and unplug the power plug.
Bring it to the customer service center, do not dismantle or modify the product by
yourself.
֭
The product and its power plug should be installed in a position where water
or detergent can't be spilled.
֭
Do not touch with wet hands
Do not disassemble
Do not touch water
1. Do not use inappropriate cleaners when cleaning
and maintaining plastic parts.
֭ Use of toilet detergent, residential detergent, bleach,
gasoline, thinner, detergent, cresol, etc., will lead to
֭
3. If the product will not be in use for a long time, drain the water and pull out the power
֭
֭ Otherwise, the water inside the product will be contaminated, which will lead to the
4. When the following people use the product, please accompany them to prevent them
from falling. (Children, the elderly, people who can't sit or stand on their own).
֭ Children should not play with this product. Do not let children use this product alone.
֭ Otherwise, people may be injured or the product cover may be damaged.
5. In the room where the product is installed, a water supply switch should be installed
ATTENTION
05

without tools in case of emergency. Otherwise, the accidental failure of the product may
cause personal injury or property loss.
֭
֭
2. Do not touch or step on the faucet.
֭
֭Otherwise it may cause scratches or damage to the cover.
Do not place cigarettes and other combustible materials near the product.
֭
06

3. Preparations before installation
1
2
4
5
6
7 8
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
18
18
3
1
Remote control and holder
2The side button
4Upper cover
3Bidet seat
Inlet water pipe
Filter
6Night light
7Front wash plughole
9Nozzle
8Rear wash plughole
5Warm dry Adjustment sheet
Bolts
Battery
07

4.5mm
Drill
Cross screwdriver
Electric drill
Cup
Tape
515mm
392mm 128mm
Preparations before installation
In the room where the product is
installed, a water supply switch
should be installed in the accessible
position. This switch can be used to
without tools in case of emergency.
Otherwise, the accidental failure of
the product may cause personal injury
or property loss.
Suggestions for connecting power supply and water inlet.
250mm
100mm
200mm
>500mm
08

4. Packing list
list
Designation
Electronic bidet
Remove from bottom of product
Adjustment sheet
Inlet water pipe
User manual
Remote control battery (AAA)
Remote control and holder
nuts for remote control holder
1 set
1 pcs
Filter 1 pcs
2 pcs
1 pcs
2 pairs
1 set
1 set
1 pcs
2 pairs
2 pcs
Quantity
Fixed plate
Electronic bidet
User manual
Remote control battery AAA
Bolts and expanding nuts
for remote control holder
Adjustment sheet
Remote control and holder
Inlet water pipe
Bolts and expanding nuts
Expansion screw set of
leakage protection plug
Expansion screw set of
leakage protection plug
Filter
User Manual
AIB2211/97
ElectronicBidet
09

5. Installation Steps
This product has been tested before delivered in the factory, there may be a small amount
As shown in the picture, install the expanding
ĚŏŊł֤žŭâÞĻē½Ŋâ֤½ÞčŏłŊęâĚŊłüââŊÿĚġľÞâľ֣
üâĚžŭŊüâ×ġēŊłġõžŭâÞĻē½Ŋâ×ŏŊĚġŊ
completely tightened.
installed on the ceramic for trial installation,
adjust the position, then press the side of the
product push rod to remove the product, screw
the bolts down .
3.
plate slot, push it horizontally,
till
Adjustment sheet
Bolts
Click
10
4. Note:
Connect the strainer to the
Angle valve and connect two
water pipes.
Bidet fresh water inlet
pipe
Filter
Toilet fresh water inlet
pipe (if applicable)

11
Leakage protection test
(1) Under normal condition, press the "RESET" button on the power plug, the plug indicator
light will be green and the product will start to power on, enter the standby state;
(2)
(3) Press the "RESET" button on the power plug again, the indicator light will be green,
and the power supply of the product will be restored.
Turn on the tap
6. Connect the water 7. Switch on the plug
This picture is for
reference only
Indicator
light Reset
button
Test
button
A. Drill two 4.5mm diameter holes with a depth of >20mm in appropriate
positions on the wall according to the position dimensions shown.
B.
the drilled hole.
C. Secure the remote control
screws.
D. Battery installation
64
2- 4.5
Unit: mm
5. Install the remote control.
Swipe up to remove the remote control.

Warning
֭
֭
through the plug. When using other electrical appliances, the product does not
replace the basic safety measures of other electrical appliances.
֭
product plug.
8. Function test
Test run
Gently cover the sensing position on the
seat with your hand, and at the same time
press the rear wash/front wash button to
to prevent water from splashing on yourself
12
C. Fix the leakage protection plug with expansion screw.
B.Install the expansion nut into
the drilled hole.
48.5
2-4.5
A.Drill two 4.5mm diameter holes with a depth
of >20mm in appropriate positions on the wall
according to the position dimensions shown.
9. Fixing of leakage protection plug
6OJU: mm
2

50W
250W
1000W
515X392X128mm
Warm air
Warm air temperature
Heater power
Sterilizations Function
Product dimension
Water supply temperature
Waterproof level
Water temperature
Heater power
Warm water
for wash
Seat temperature
Heater power
Warm seat Room temperature ~41
Room temperature ~60
IonShield
Inlet water temperature ~41
IPX4
about 250~550ml/min (static pressure 0.2MPa)
3~35
4m/s
Warm dry
Else
820W
1050W
AIB2211/97
Designation
Model
Inductor Seat sensor
Clean and
sanitary Nozzle self-cleaning
Antimicrobial nozzle
Night light
ECO ECO setting
The rated voltage
Rated frequency
Rated power
The environment temperature
Supply pressure
Warm dry
Air temperature adjustment
Seat and
cover
Soft closing seat and cover
Antibacterial seat
Seat temperature adjustment
Electronic bidet
5 level setting
5 level setting
5 level setting + normal temperature level
5 level setting + normal temperature level
3 level setting + normal temperature level
220V~
50Hz
0~40
0.07MPa~0.75MPa
Wash
Rear wash
Front wash
Child wash
Moving wash
Water pressure adjustment
Water temperature adjustment
Nozzle position adjustment
13

7. About the the side button
Explanation:
Rated power: Under the conditions of environmental temperature 23 ±2 , static pressure
of water inlet 0.2MPa ± 0.02MPa, water inlet temperature 15 ±0.5 , the function of
is completed.
Maximum input power:
The average power of this product under the conditions of environmental temperature
23 ±2 , inlet static pressure 0.2MPa ± 0.02MPa, inlet temperature 5 ±1
of a cleaning cycle is completed.
Best cleaning performance:
water pressure
the spray position to the most front end, after cleaning for 1 minute, adjust the nozzle
position to the rear end, until the end of the washing cycle.
Since the design of this product is mainly controlled by remote control, the side button
Introduction:
The side button contains two functions: automatic rear wash and front wash.
When seated, short press the button to activate automatic rear washing function:
rear wash + moving wash + rear wash + warm dry.
When seated, long press the button (above 3 seconds) to activate automatic front
washing function: front wash + moving wash + front wash + warm dry.
When unseated, long press the button (above 10 seconds), shut dowm all function, and
Side button indicator
Auto/stop
14

8. About the remote controller
Seat temperature
button (Long press
for power saving)
IonShield button
Front wash/ Move button
Water pressure
increase button
Position forward button
button
Night light button
Rear wash/
Move button
Water pressure
reduction button
Children's washing
button
Water temperature
adjusting button
(Long press for nozzle
self-cleaning)
Air temperature
adjusting button
mode/ stop button
/ /
/
15

1. Rear wash/ Move button
after rear wash for about 3 minutes or leaving the seat, or press the “ ” button to
Press “ ”button again to stop the mobile wash.
2. Front wash/ Move button
after front wash for about 3 minutes or leaving the seat, or press the “ ” button
Press “ ” button again to stop mobile wash.
3. Children wash
pressure, water temperature and air temperature to the lowest gear for hip washing
for 1 minute, and then automatically turn on the warm air for 2 minutes. After that,
restore the previous water pressure, water temperature and air temperature.
4. Water temperature adjustment
Press“ ”button, the indicator light shows the water temperature level; press
“ ”button again, the water temperature level can be switched, each level can be
below:
5. Water pressure adjustment
In rear wash / front wash mode, press " " button once to increase the water pressure
6. Position adjustment
Under the rear wash/ front wash mode, Each time you press the " " button, the
9. How To Use
/
/
First gear Second gear Third gear Fourth gear Fifth gear
First gear Second gear Third gear Fourth gear Fifth gear
16

" "
can be adjusted.
7. Nozzle Cleaning
for cleaning for about 2 minutes, operate the nozzle again to retract and self-clean.
8. Seat temperature setting
9. Night light
Press the " " button to turn on the night light, and then press the " " button
10. Warm air function
- When seated, press “ ”button to start the warm air function; it will stop
automatically for about 5 minutes or after leaving the seat, or press the “ ”
- In warm air mode, press the “ ”button, the indicator light shows the wind temperature
11. Power saving
12. Automatic working mode/stop button
13. IonShield
-
First gear Second gear Third gear Fourth gear Fifth gear
Normal
temperature First gear Second gear Third gear Fourth gear Fifth gear
/
Normal
temperature First gear Second gear Third gear
/
17

10. Maintenance
- When the IonShield is turned on, the aperture on the side button shows strong
-
on according to the above logic until the function is completed or stopped.
- After entering the IonShield sterilization function, if you press long / short to switch
- During the operation of IonShield sterilization function, press " " or sit down
/
and other hazards.
Bidet cleaning
1. Pull out the power supply, close the angle valve
2. Bidet cover cleaning
Wipe with a soft cloth and water (to be wrung out)
Notes:
- The product surface is made of plastic. Do not wipe it with dry cloth or toilet paper.
Otherwise, it may damage the appearance of the product;
This picture is for
reference only
18