Philips LCU7725/00 User manual

Input from Transmitter
490V square wave
Neutral in/out
in out
Transmitter
0.8...2.0 mm2(AWG 18...14)
Torque: 4 Kgf.cm
Neutral in/out
10...25 mm2 (AWG 8...4)
Torque: 20.7 Kgf.cm
63 A max
7.5 ±0.5 mm
(0.3 ±0.02 in)
use copper
conductors
only rated
75 ˚C min
use copper
conductors
only rated
105 ˚C min
13 ±0.5 mm
(0.5 ±0.02 in)
N
transmitter
12
4422 107 05496 17 December 2018
Coded Mains
Transformer LN
LCU7725/00
120 mm (4.7 in)
26 mm
(1.0 in)
N
in out
transmitter
12
139 mm (5.5 in) max
129 mm (5.1 in) max
108 mm (4.3 in) max
5.5 mm (0.22 in) 4x
7 mm (0.3 in) 4x
1
kg
3.1 kg
min
-20° C
max
60° C IP00
www.philips.com/lighting
Installation Instructions
Instructions d’installation Istruzioni per l’installazione Installationsanweisungen 安装指示书
Instrucciones de instalación Installatie-instructies インストール手順 
≤90%

transmitter
1 2
N
in out
wire isolation rating > 1kV
twisted wire
N
L1
L2
L3
Connect to earth
LFC7710
Recommendation:
Install horizontally mounted at
bottom of cabinet if possible.
Cabinet IP rating IP65 or above.
B Warning
In case of vertical mounting
please make sure the transformer
is securely mounted considering
the weight. Also it is advised to
mount as low as possible. In case
transformer is not securely
mounted and would drop, it
might cause high currents and
there is a risk for electrical shocks.
4x screw
B Warning
Remove the jump wire when
connecting to transmitter
LFC7710 and power on.
Disconnect
power
Product Guide
2
4
B CAUTION
Safety and High Voltage Warning
Ensure that the AC power mains are turned OFF before
handling the mains wiring, or connecting any power mains
cabling to the LCU7725/00 device.
Restrictions haute tension et sécurité
Assurez-vous que les prises secteurs de courant CA sont
désactivées avant de manipuler les câblages secteurs
ou de connecter toute source d’alimentation à l’appareil
LCU7725/00.
Advertencia sobre seguridad y alta tensión
Asegúrese de que la corriente de red CA esté apagada
antes de manipular los cables de red eléctrica o de conectar
cualquier cable de red eléctrica al dispositivo LCU7725/00.
Avvertenza sulla sicurezza e sull’alta tensione
Assicurarsi che l’impianto elettrico CA sia spento prima di
maneggiare il cablaggio elettrico o di collegare eventuali cavi
elettrici al dispositivo LCU7725/00.
Veiligheid en waarschuwing voor hoogspanning
Zorg dat de netspanning is afgesloten voordat u de
netspanningsdraden vastpakt of netspanningskabels op de
LCU7725/00 aansluit.
Sicherheits- und Hochspannungswarnung
Stellen Sie sicher, dass die Stromversorgung
AUSGESCHALTET ist, bevor Sie Netzkabel berühren oder mit
dem LCU7725/00-Gerät verbinden
安全および高電圧に関する警告
配電線を取り扱う前、または LCU7725/00 デバイスに送電する
電力線を接続する前に、必ず、 AC 電源を「オフ」にしてくだ
さい。
安全与高压电警告
请确保先关闭交流电路，然后再操作电源连线或者将任何电源线路
连接至 LCU7725/00 设备
EN
FR
NL
DE
IT
JA
ZH
ES
3
5
© 2018 Signify Holding. All rights reserved. Specications are
subject to change without notice. No representation or warranty
as to the accuracy or completeness of the information included
herein is given and any liability for any action in reliance thereon is
disclaimed. Philips and the Philips Shield Emblem are registered
trademarks of Koninklijke Philips N.V. All other trademarks are
owned by Signify Holding or their respective owners.
4422 107 05496 17 December 2018 www.philips.com/lighting