Philips SLV3100/05 User manual

Wireless TV Link
User Manual
SLV3100

E151514
A
B
SLV3100 WIRELESS TVLINK TRANSMITTER
SLV3100 WIRELESS TVLINK RECEIVER
ON/OFF
Channel
IR
1 2 3 4 ON/OFF
DC 9V
ON/OFF
Channel
1 2 3 4
DC 9V
ON/OFF
1 2
34567
8 9
10111213

3
EN
Contents
Page
Overview 4
Control and display elements 4
Your Wireless TV Link 5
Safety 5
Installation 6
Operation 8
Enjoy your Wireless TV Link 8
Troubleshooting 9
Information 11
Health and safety 11
Maintenance and service 11
Recycling and disposal 11
Warranty 12
Glossary 12

4
EN Overview
Control and display elements
A Transmitter
1 Power light:
> green: on
2 Remote control signal light
3 On/off switch
4 Power input connector (DC 9V)
5 SCART cable
6 Wireless channel selection switch
7 Remote control blaster cord port
B Receiver
8 Power light:
> green: on
9 Remote control signal light
10 On/off switch
11 Power input connector (DC 9V)
12 SCART cable
13 Wireless channel selection switch
E Remote control blaster cord
14 Connector
15 Blaster light

5
EN
Your Wireless TV Link
You can say good-bye to wires. With your Wireless TV
Link you can now wirelessly connect a second TV and
watch the device on your second TV.
Safety
• Read the instructions in this manual carefully before
you connect, install and use the product.
• Keep this manual for future reference.
• The product is for indoor use only.
• Do not use the product close to water.
• Do not expose the product to extreme heat.
• In case of technical difficulties, do not open the
product. Bring it to your Philips dealer.
• Do not cover the product.
• Connect the power adapters only to a
220-240 V AC/50 Hz power supply.
• The product can cause interference to other
equipment. Check if any equipment near the product
can be affected before you start using it.

6
EN Installation
Install the remote control blaster cord
1 Switch off the transmitter (A).
2 Connect the remote control blaster cord (E) to the
IR socket.
3 Position the blaster light in front of the video source.
4 Switch on the transmitter (A).
5 Take the remote control of a video source with you.
6 Go to TV2.
7 Switch on TV2.
8 Switch on the receiver (B).
9 Select the correct SCART input on TV2.
10 Operate the video source with its remote control.
For basic installation, see
the quick start guide that
came with your Wireless
TV Link. 3Enjoy
DC 9V
ON/OFF
1 2 3 4
See the user manual of the video source
for the exact location of the IR sensor
on the front panel.
DC 9V
ON/OFF
DC 9V
ON/OFF

7
EN
Installation
Remove interference on TV2
1 Find the CHANNEL switch on the transmitter (A).
2 Set the CHANNEL switch to a different number.
3 Find the CHANNEL switch on the receiver (B).
4 Set the CHANNEL switch to the same number as
on the transmitter (A).
1 2 3 4
1 2 3 4

8
EN Operation
Enjoy your Wireless TV Link
Watch a cable TV program on TV2
1 Switch on the transmitter (A).
2 Switch on the VCR or DVD recorder.
3 Take the remote control of the VCR or DVD
recorder with you.
4 Go to TV2.
5 Switch on TV2.
6 Switch on the receiver (B).
7 Select the channel on the VCR or DVD recorder
with its remote control.
Watch a video source on TV1
Operate TV1 and the video source as usual.
For basic operation, see
the quick start guide that
came with your Wireless
TV Link. 3Enjoy
Your VCR or DVD recorder needs to
be connected to the transmitter (A) of
the Wireless TV Link and connected to
the Cable-TV signal.
DC 9V
ON/OFF
DC 9V
ON/OFF
Turn off the auto standby mode when
you use the VCR or DVD recorder to
watch a cable tv program. Refer to the
user manual of the VCR or DVD
recorder.
If the VCR or DVD recorder records a
television program, you watch the
recorded channel.

9
EN
Troubleshooting
Problem Tip
No image or
wrong image on
TV1
• Make sure video source is con-
nected to the transmitter (A).
• Make sure the transmitter (A) is
connected to TV1.
• Make sure SCART cables are
firmly inserted.
• Make sure the video source is
switched on.
• Make sure the correct SCART
input on TV1 is selected.
No image or
wrong image on
TV2
• Make sure SCART cables are
firmly inserted.
• Make sure the receiver (B) is con-
nected to TV2.
• Make sure both receiver (B) and
transmitter (A) are switched on.
• Make sure the video source is
switched on.
• Make sure the correct SCART
input on TV2 is selected.
• If the video source gives proper
image on TV1:
Make sure the video source gives
video signal in CVBS mode. See
its user manual
• Change the wireless channel that
is used for communication. See
page 7.
• The receiver (B) is out of range of
the transmitter (A). The number
of walls and ceilings in between
the receiver (B) and transmitter
(A) restrict the distance.

10
EN Troubleshooting
Problem Tip
Interference in the
image on TV2 •
Slightly change the position of the
receiver (B) or the transmitter (A).
• Change the wireless channel that
is used for communication. See
page 7.
• The receiver (B) is out of range of
the transmitter (A). The number
of walls and ceilings in between
the receiver (B) and transmitter
(A) restrict the distance.
The video sources
do not respond to
the remote con-
trol commands
from TV2
• Point the remote control directly
to the receiver (B).
• Replace the batteries of the
remote controls with new ones.
• Install the remote control blaster
cord (E). See page 6.
• The maximum operating distance
of the remote control is 5 m.
The image of the
video source dis-
appears on TV2
• Turn off the auto standby mode
of the video source. See its user
manual.
• Follow the instructions to recon-
nect the video sources. See the
quick start guide.
Buzzing sound
when you use the
remote control.
• Slightly change the position of the
receiver or the transmitter until
the buzzing sound stops.
• Sometimes it is not possible to
solve the problem.
Black and white
image with S-VHS
VCR.
• Check if the SCART connector of
the S-VHS VCR gives signal in
CVBS. See its user manual.