Phoenix Baby GoTo GT201 User manual

Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
MODEL # GT201
PRN: GT201-PNX [15.06.25]AIM-
A
2 IN 1 INFANT CAR SEAT STATION AND HI CHAIR STAND
Caution : When setting up for the first time, do not have child in infant car seat.

IMPORTANT INFORMATIONS
Care MUST be taken when folding and unfolding the GoTo.
Prevent serious injury or death from falls or sliding out. ALWAYS use seat belt.
Secure your child at ALL times with the restraint.
This product is designed to be used by a child up to 3 years of age.
MAXIMUM WEIGHT 40 pounds (18kg).
Children have
FULLY restrain the child at all times.
STRANGLED in loose or partially buckled harness straps.
The child
system. It is recommended that the high chair be used ONLY by children
capable of sitting upright unassisted.
MUST be secured in the high chair at times by the restraining
!Please follow all of these instructions to ensure the safety of your child. Keep
these instructions for future reference.
!Adult assembly required.
!Failure to follow these instructions could result in serious injury or death. Avoid
serious injury from falling or sliding out, always use the safety harness and insure
that the children are properly positioned according to these instructions.
!Caution: Be certain the GoTo is completely opened and locked in place before
allowing a child near the product.
!Never use near steps or uneven surfaces.
!Never allow your GoTo to be used as a toy.
!Check your GoTo for loose screws, worn parts, torn materials or stitching on a
regular basis. Replace or repair parts as needed.
!Discontinue use should it malfunction or become damaged. Please contact
our customer care department to arrange for repair or obtain replacement
parts if needed.
!If you experience any difficulty with the use of our product or have a question
regarding these instructions, please contact our customer care department at
800-704-9058.
!To clean use only mild household soap or detergent and warm water on a
sponge or clean cloth.
Customer Care:
www.phoenix-baby.com
NEVER leave children unattended.
WARNING
2

PARTS
Remove product from box, take
the product out of the travel
bag and remove all packaging
materials from the product.
Make sure to throw
away all packaging materials.
CAUTION :
Stand the four feet
on the ground.
Open the product by grabbing the 2
opposite sides as shown and pulling outward
until the product is almost completely open.
2
Note : you will need to lift the product off the ground so that the non slip feet do not stick to the
floor as you are opening and closing the product.
Male
Female
3
TO OPEN PRODUCT FOLLOW THESE STEPS EVERY TIME
1

TO OPEN PRODUCT FOLLOW THESE STEPS EVERY TIME
Warning : AVOID FINGER ENTRAPMENT : Use care when folding and unfolding the GoTo.
Be certain GoTo is fully erected and latched before allowing your child near the GoTo.
Push down on the 2 side latches until they are locked in the down position.
3
SET UP AS AN INFANT CAR SEAT STATION
1A
Buttons and Velcro
Leg enclosure
Your GoTo is shipped with the leg enclosure panel in
the up position. You will need to lay the panel flat
so that your Infant car seat sits INTO the enclosure.
1a. Identify the components to your GoTo.
4
To set up as an infant car seat station : page 4.
To set up as High Chair : page 7.
To convert back to an infant car seat station : page 10.

SET UP AS AN INFANT CAR SEAT STATION
Lay back support down over the leg
enclosure.
1B 1b and 1c. Unsnap the 2 buttons of the leg
enclosure and pull down on the Velcro, repeat
on other side.
1C 1D
5

SET UP AS AN INFANT CAR SEAT STATION
(YES) (NO)
1E Insert your infant car seat
into the station.
For the most up to date list of car seats
and how they are to be installed into
our Station. Go to our website.
Caution : Make sure your car seat is on
the same angle as when you place the
infant car seat in your car or stroller.
1F Make sure all sides are
Surrounded by the fabric.
1G Using the Red male
and Red female
connectors, strap the
safety belt over
the lower part of the
infant car seat
by and connect.
Tighten strap so
that infant car seat is
firmly attached
and secure to frame.
Warning : Avoid serious injury from falling or sliding out, always use the safety car seat
harness to secure child.
Warning : Do not move with child in the station. 6

SET UP AS A HIGH CHAIR
2To set up as a High chair please follow these steps.
Lift up high chair back panel.
2A-2C
Lift up and attach the leg enclosure panel. Starting at
the bottom of each side of the panel, attached the
Velcro sides, then button both buttons on each side.
If you are having problems lining up the buttons,
detach the Velcro and start again.
1
2A
2B 2C
7

SET UP AS A HIGH CHAIR
If High Chair back and leg enclosure is not latched or is lying down, follow these steps.
Insert female connector through fabric
slot on the top sides of the product.
2E2D Lift back support up.
2F Connect female connector to the Male connector on both sides. Pull on straps to
make tight.
Note : you may loosen the
straps to enlarge the area of
the high chair as your child
grows.
Note : You will need to lay
the red safety straps inside of
the station while buckling
the back support buckles.
8
2G Strap the safety belt with red connectors
behind the seat, away from child. This
can give your young child some extra
support. As your child grows, you should
let out some of the belt to make more room.
loose straps can cause strangulation.Warning :

Insert the female strap thru the crotch strap
loop and attach to the male strap.
Make sure tighten strap so that child cannot
skip out of chair.
Female Strap Crotch Strap
with Loop
Male Strap
TO SECURE CHILD IN HIGH CHAIR
WARNING
Falling Hazard: Always use the seat belt.
9
1C 2C 3C
Disconnect female
connector from the
male connector on
both sides.
CONVERT FROM HIGH CHAIR TO INFANT CAR SEAT STATION
Slide female connector
through fabric slot on
both sides of the
product.
Lay back support down,
then go to page 5 and
follow set 1b.

BackFront
www.phoenix-baby.com
www.phoenix-baby.com
Phoenix Baby, LLC.
c/o RBO, LLC.
PO BOX 91058
ALLENTOWN PA 18109-9917
Manufacturer's Contact Information/Coordonnées du fabricant
Phoenix Baby, LLC. (c/o RBO, LLC.)
501 S 9TH Street, Reading, PA 19602 USA
Customer Care: 1-800-704-9058
E-Mail: [e-mail]
www.phoenix-baby.com
Product Model/Modèle de produit#:
Shipment Ref./Réf. d'Expédition#:
Manufacture Date/date de fabrication:
KEEP THIS TOP PART FOR YOUR RECORDS.
FILL OUT AND RETURN BOTTOM PART.
GARDER CETTE PARTIE SUPÉRIEURE POUR VOS DOSSIERS.
REMPLIR ET RENVOYER PARTIE INFÉRIEURE.
Name/nom
Mailing Address/Mailing Address
City/ville Zip Code/Code postalState/état
Telephone Number/numéro de téléphone
E-mail Address/Adresse E-mail
Product Model #:
Shipment Ref./Réf. d'Expédition#:
Manufacture Date/date de fabrication:
/Modèle de produit
3D To fold.
Lift up both latches at the same time. Continue to
lift until product is folded.
Place in travel back, seat area first. Once fully
bag, pull cord to close.
AVOID FINGER ENTRAPMENT : Use care
when folding and unfolding the GoTo. Be certain
GoTo is fully erected and latched before allowing
yo child near the GoTo.
Warning:
PRODUCT REGISTRATION
IMPORTANT: Please fill in your contact info on the bottom part of the card,
separate from top card and mail to us. Note, postage is prepaid if mailed in the
United States. Keep the top portion for your records. This information is important
to us should we need to contact you regarding the safety of this product.
10

MADE IN CHINA
501 S 9th street,
Reading, PA 19602 USA
www.phoenix-baby.com
Product Name/Nom du Produit
Shipment Ref./Réf.d'Expédition#: Date/Date:
Color/Couleur:
Model/Modèle #:
8 61 7 5 9 2 0 1 9 5 7
GREYGT201-001
000-091914-001 YYYY/MM/DD
2 IN 1 INFANT CAR SEAT STATION
AND HI CHAIR STAND
PRODUCT PACKAGING INFORMATION
The following packaging information is also found on Right Back Leg.
Made in:
Address:
Product ID/Date Code:
501 S 9th Street, Reading, PA 19602 USA
Phoenix Baby LLC
Importer by:
China
1412WBPGT201
CAR SEATS COMPATIBLE WITH YOUR GOTO STAND
The list below identifies a few of the car seats that are
compatible with your Got To Station. To see the
complete and most up to date list go to:
www.phoenix-baby.com/goto/compatiblecarseats
Brand BrandProduct Name Product Name
Bob B-safe (made by Britex)
Britax B-Safe
B-safe-30
B-safe-35 elite
B-safe-35
B Safe 35ELite XE
Flex-Loc 30
Inertia
Flex -Loc
KeyFit 30
Light 'n Comfy Elite
Light 'n Comfy luxe
Shuttle
B-safe-30
Chicco Key fit
Baby Trend
Go-lite EZ
Chicco
Cosco
Disney
Combi
Graco SnugRide Classic
SnugRide 35 Click Connect
SnugRide Click connect 30
SnugRide Click connect 35
SnugRide Click connect 35LX
SnugRide Click connect 40
NXT
Micro Max 30
Mico Nxt
Prezi
Promo Viaggio 4-35
Performance Coupe
The First years Contigo InTrust 35
Uppababy Mesa
Peg Perego
Maxi-Cosi
Embrace
Embrace Lx
Nuture
Asana 35 AP
Evenflo
GB
Newport
Mico AP
OnBoard 35 Air +
OnBoard 35 Air
OnBoard 35
OnBoard Plus
Ingenuity
Safety1St
GB
JJ Cole
Comfy Carry Elite
Elite
Summer Infant Prodigy
Contigo Infant Car Seat
Place PPI Box Label Here
11