Phoenix Doors Enviro 6S User manual

Sliding Gate Operator
User's Manual
E N V I R O 6 S
G e a r -D r i v e n
http://www.phoenixgaragedoors.com.au/

ENVIRO 6S SLIDING GATE OPERATOR
1
OUTLINE
1. Products introduction 2
2. Important safety precautions 2
3. Main technical parameters 2
4. Mechanical Installation 3
5. Adjustment5
6. Wire Connecting 6
7. Electrical and control board 7
8. Porgramming Process 8
9. Maintenance 10
10. Trouble Shooting 11
11. Packing list 11
12. Warranty Registration 11

ENVIRO 6S SLIDING GATE OPERATOR
2
1. Products introduction
please read the instructions carefully before proceeding.
The operator contains Extra battery, transformer, control board and radio control.
In case of power of failure, the operator is powered by a 24Vdc, 1.3Ah, extra battery.
Intelligent charging system supplied.
MCU is supplied to control the gate operator.
Keypad / single button interface.
Photo beam safety beam interface.
User can select Auto-close feature
Soft start & soft stop.
Manual key release design for emergency purposes.
Gate operator has auto-reverse function, and the reverse power can change by user.
2. Important safety information
Carefully read and follow all safety precaution and warnings before attempting to install and use this
automatic gate operator.
Make sure the Power supply(AC220V) of operator is suitable for the power supply in your area.
3. Main technical parameters
Unit Model ENVIRO 6S
Power Supply 220VAC
220V AC
110V AC
Maximum gate weight 300Kg
Maximum gate width 8m
Motor 24VDC 100W
Output torqueMax. 8N m
Work duty S
2
30min
Limit switch
Electronical Limit
Gate Move speed13m/min
Remote control range30 meters
extra remote control 20
100 (2 included)
Frequency 433.92 MHz
Noise 60 dB
Working temperature -20 C ~ +50 C
Extra Battery 24V 1.3 Ah

ENVIRO 6S SLIDING GATE OPERATOR
3
4. Mechanical Installation
The ENVIRO 6S will handle gate weighting up to 300Kg and up to 8m if the proper installation procedures
have been followed.
The ENVIRO 6S gate operator operates by forcing a drive rack by a drive gear. The entire configuration
is shown in the diagram below. The gate operator must be installed on the inside of the gate.
Sliding gate
Gate operator
Rack
Switch
Input power
Wall
Fig.1
Gate preparation
Be sure the gate is properly installed and slides smoothly before installing the ENVIRO 6S sliding gate
operator. The gate must be plumb, level, and move freely.
Conduit
In order to protect the wires, use PVC conduit for low voltage power cable and control wires. Conduit
must be preset into the concrete when it is poured. Wires within the conduit shall be located or protected
so that no damage can result from contact with any rough or sharp part.
Concrete pad
The base unit of the gate operator requires a concrete pad in order to maintain proper stability. The
concrete pad should be approximately 400mm x 250mm x 200mm deep in order to provide for adequate
weight and structure to insure proper stable installation.
Anchors (see Fig.2)
You can use anchor bolts, anchors, washers and nuts. These anchors must be set into the concrete
when it is poured or you can use wedge anchors to fasten the operator.

ENVIRO 6S SLIDING GATE OPERATOR
4
Gate operator
Gear
Groundsill
Input power
Plain washer
Nut
Spring washer
Nut
Fig.2
Operator base (see Fig.3)
After the concrete has hardened, mount the gate operator base to the concrete pad. Verify that the base
is properly leveled.
Using bolts and washers mount the gate operator to the base and insert the cover. Check the operator
and make sure it is lined up with the gate.
Fig.3

ENVIRO 6S SLIDING GATE OPERATOR
5
Installation of Rack
Fix the three nuts (in the same package with rack) on the rack element.
Laythe first piece of rack on the gear and weld the first nut on the gate.
Move the gate manually, checking if the rack is resting on the gear, and weld the second and third nut.
Bring another rack element neartothe previous one. Move the gate manually and weld the three nuts
as the first rack, thus proceeding until the gate isfully covered.
When the rack has been installed, to ensure it meshes correctly with the gear.
The space between rack and gearis about 0.5mm.
Fig.4
5. Adjustment
Sliding gate
Rack
Gear
Fig.5

ENVIRO 6S SLIDING GATE OPERATOR
6
Manual operation
In case of power failure use manual release key to open or close gate manually, use the release key as
follow:
Fit the supplied key in the hole.
Turn the key clockwise to release the clutch.
Open and close the gate manually.
After power-restored use the manual release key totight the clutch by turning the key
counterclockwise and resume normal operation.
Fig.6
NOTE The gate operator needed reset limit after re-tight the clutch by turning the key
counterclockwise if the power failure and released by hand.
6. Wire Connecting
Connecting the battery
Plug the terminal of Extra battery in the control board.
NOTE:If you not use gate operator and power failure, please pull out the extra battery terminal.
Fig.7
Release
Release keyRelease hole
Battery
BLACK TO Charge BAT -
RED TO Charge BAT +
Battery
RED TO SOLAR BAT +
BLACK TO SOLAR BAT -
SOLAR PANEL

ENVIRO 6S SLIDING GATE OPERATOR
7
Connecting the motor
Connect motor wires to M- and M+ of terminal block T1 (BLACK)and T2(RED).
Connecting power wire
Fig.8
7.Electrical and control board
Fig.9
Motor: black wire to T1 and red wire to T2.
J1: transformer secondary(AC24V/3.3A)
external Push Button(J2,J3,J4):
Single Button(OSC and COM)
Three Button(K,G,T,and COM),
Photo beam(PE and COM)
Output DC power: 24 and GND
J5: solar panel(10W 27V) and charge Battery.
NOTE: Please put through the J5 (Battrey) terminal, if you need use the sliding gate
L
N
PE
Transformer
primary
Power
supply
AC220V

ENVIRO 6S SLIDING GATE OPERATOR
8
operator.
8. Programming Process
SET button: Mode set and Confirm function
CODE button: Transmitter set and clear function
OPEN button: open door
CLOSE button: close door
SET CODE
OPEN
CLOSE
Fig.10
Adding extra transmitter (learn)
1. Press CODE, a dot is indicated on the LED display.
2. Press the transmitter button which you want to use (button 1, 2, 3, 4), then press the same button
again.
3. The dot on the LED display will flash then turn off.
4. ’||’ is indicated on the LED display, then the learning process is finished.
Up to 20 transmitters may be used.
SET CODE
CODE
SET SET CODE
12
34
OPEN
CLOSE
OPEN
CLOSE
OPEN
CLOSE
Fig.11
Erase transmitter
Press and hold CODE until ’C’ flashes on the LED display. This indicates that all the transmitters have
been erased completely.
SET CODE
OPEN
CLOSE
Fig.12

ENVIRO 6S SLIDING GATE OPERATOR
9
Set open and close positions
1. Press and hold SETuntil number 1is indicated on the LED display.
2. Press and hold OPENto set open position(now the door must be OPEN,, if not,please change the
motor wire red and black), release the button until the door has reached the desired position. (You
also can press CLOSE to move the door close, OPENand CLOSE can be used to fine adjust the
door position.)
3. Press the SETto confirm the open position, now number 2is indicated on the LED display.
4. Press and hold CLOSE to set close position, release the button until the door has reached the
desired position. (You also can press OPEN to move the door open,OPENand CLOSE can be used
to fine adjust the door position.)
5. Press the SETto confirm the close position.
6. The door will do a complete open and close cycle.
CLOSE
CODE
OPEN
SET SET
OPEN
CODE
CLOSE
SET
OPEN
CODE
CLOSECLOSE
CODE
OPEN
SETSET
OPEN
CODE
CLOSE
Fig.13
Automatic close (0~90 seconds adjustable)
1. Press and hold OPENuntil is indicated on the LED display.
2. Press OPENto increase the auto close time, press CLOSE to decrease time.
3. Set timer to 0, the automatic close function will disable.
4. Press SETto confirm the setting.
5. Add 10 second per number
NOTE: Automatic close function is available only when the doorisin fully opened position.
SET CODECODE SETSET CODE
OPEN OPEN OPEN
CLOSE CLOSE CLOSE
Setting obstruction force

ENVIRO 6S SLIDING GATE OPERATOR
10
If the door meet an obstruction during closing, it will stop and reverse about 15cm~20cm.
1. Press and hold SET. The LED will display number from ’1’ to ’4’, when the number ’3’ appears on the
LED display, release the SET.
2. Press OPEN to increase the obstruction force, the maximum force is level 9. Press CLOSE to
decrease force, the minimum force is level 1.
3. Press SET to confirm.
Fig.14
Photo beam:
Connect the photo beam follow Figure. The photo beam output signal must be N.C. signal.
Press and hold close until ’─’ is indicated on the LED display. release the close,’11’will indicated on
the LED display. Press open, ’H’ will indicated on the LED display. Press SET to confirm.Then
Connect the photo beam follow the Figure.(Note: When not using photo beam, please click the
above action and set to "11" status)
Photo receiver Photo transmitter
GND
PE
24
Fig.15
9. Maintenance
!Check the door once a month. The door should be carefully checked for balance. The door must be
in good working order.
!The auto-reverse function should be regularly inspected, and adjusted if necessary. For service, call
an experienced serviceman.
!We suggest for safety reasons, photocells be used on all gates.
!Disconnect from mains supply before replacing bulb.

ENVIRO 6S SLIDING GATE OPERATOR
11
Be sure to read the entire manual before attempting to perform any installation or service to the door
operator.
Our company reserves the right to change the design and specification without prior notification.
10. Troubleshooting
Trouble Possible causes Solutions
The door fails to open
and close. LED display
does not light.
1. Power is OFF
2. Fuse burn
1. Make sure that power is ON.
2. Replace fuse.
The door can open, fails
to close.
1. Infrared beamis obstructed.
2.Infrared photocell function is
enable, but the photocell has not
been installed.
1. Remove obstructions.
2.Make sure the infrared
photocell function is disable.
Remote control does not
work.
1. Battery level may be low,
2. Transmitter
1. Replace the battery inside the
transmitter.
2.Re-program the transmitter.
The transmitter operating
distance istoo short. Battery level may be low. Replace battery.
11. Packing list
After receiving the gate operator, you should make an unpack-inspection, in which you should check
whetherthe product was damaged. If you have any problem please contact our dealer. You should find
the following items in our standard packing:
No. Item Quantity
1 ENVIRO 6S sliding gate operator 1
2 hand transmitter 2
3 Release key 1
4 User s manual 1
12 . Warranty Registration
For your operator warranty registration, please visit our website
www.phoenixgaragedoors.com.au/warranty-registration/