Phoenix Model TUCANO 60CC User manual

Instruction Manual
GP
version EP version
TUCANO 60CC
SCALE 1:4 ¼ ARF
SPECIFICATION
- Wingspan: 2567mm (101in)
- Length: 2190mm (86.2 in)
- Flying weight: 11-13 kg
- Wing area: 101 dm2
- Wing loading: 99g/dm2
- Wing type: Naca airfoils
- Covering type: Genuine ORACOVER®
- Retract gear type: Air-retract With CNC
Suspension Metal Struts (included)
- Spinner size: 115mm (included)
- Radio: 6 channel minimum (not included)
- Servo: 10 standard hi-torque servo: 2 aileron;
2 ap; 2 elevator; 1 rudder;1 retract; 1 throttle;
1 steering nose. (not included)
- Recommended receiver battery:
6.0V 2400/2600mAh NiMH (2) (not included)
- Servo mount: 21mm x 42 mm
- Propeller: suit with your engine
- Engine: 50- 60 CC gas engine (two stroke)
(not included)
- Motor: brushless outrunner 2600-3000 W,
190 KV (not included)
- Gravity CG: 141 mm (5.5 in) Back from the
leading edge of the wing, at the fuselage
- Control throw Ailerons: Low: 12mm up/down,
10% expo; High: 15mm up/down, 10% expo
- Control throw Elevators: Low: 12mm up/down,
12% expo; High: 15mm up/down, 12% expo
- Control throw Rudder: Low: 30mm right/left,
15% expo; High: 45mm right/left, 15% expo
- Control throw Flaps: Mid: 25mm down;
Landing: 35mm down
- Experience level: Intermediate
- Plane type: Scale Military
RECOMMENDED MOTOR AND BATTERY SET UP
- Motor: Hacker A60 (not included)
- Propeller: 22x10 E; 22x12 E APC (not included)
- Lipo cell: 12 cells / 5500 – 6000mAh (not included)
- Esc: 120-160A / HV (not included)

TOOLS AND SUPPLIES NEEDED.
• Medium C/A glue
• 30 minute epoxy
• 6 minute epoxy
• Hand or electric drill
• Assorted drill bits
• Modeling knife
• Straight edge ruler
• 2 bender plier
• Wire cutters
• Masking tape
• Thread lock
• Paper towels
• Rubbing alcohol
SAFETY PRECAUTION:
• This is not a toy
• Be sure that no other flyers are using your radio
frequency.
• Do not smoke near fuel
• Store fuel in a cool, dry place, away from
children and pets.
• Wear safety glasses.
• The glow plug clip must be securely attached to
the glow plug.
• Do not flip the propeller with your fingers.
• Keep loose clothing and wires away from the propeller.
• Do not start the engine if people are near. Do not
stand in line with the side of the propeller.
• Make engine adjustments from behind the propeller
only. Do not reach around the spinning propeller.
The painted and plastic parts used in this kit are
fuel proof. However, they are not tolerant of many
harsh chemicals including the following: paint thinner,
C/A glue accelerator, C/A glue debonder and acetone.
Do not let these chemicals come in contact with the
colors on the covering and the plastic parts.
Please trial fit all the parts. Make sure you have the
correct parts and that they fit and are aligned properly
before gluing! This will assure proper assembly. The
TUCANO 60CC SCALE 1:4 ¼ ARF is hand made
from natural materials, every plane is unique and
minor adjustments may have to be made. However,
you should find the fit superior and assembly simple.
NOTE:
To avoid scratching your new airplane, do not
unwrap the pieces until they are needed for assembly.
Cover your workbench with an old towel or brown
paper, both to protect the aircraft and to protect the
table. Keep a couple of jars or bowls handy to hold the
small parts after you open the bag.
PREPARATIONS
Use a covering iron with a covering sock on
high heat to tighten the covering if necessary.
Apply pressure over sheeted areas to
thoroughly bond the covering to the wood.
TUCANO 60CC
Instruction Manual
1

2
TUCANO 60CC
Instruction Manual
INSTALLING THE AILERONs AND FLAPs
SERVOS
1. Install the rubber grommets and brass eyelets onto
the aileron servo.
2. Using a modeling knife, remove the covering from over
the pre-cut servo arm exit hole on the aileron servo
tray / hatch. This hole will allow the servo arm to pass
through when installing the aileron pushrods.
3. Place the servo into the servo tray. Center the servo
within the tray and drill pilot holes through the block
of wood for each of the four mounting screws
provided with the servo.
4. Using the thread as a guide and using masking
tape, tape the servo lead to the end of the
thread: carefully pull the thread out. When you
have pulled the servo lead out, remove the
masking tape and the servo lead from the
thread.
5. Place the aileron servo tray / hatch into the servo
box on the bottom of the wing and drill pilot
holes through the tray and the servo box for
each of the four mounting screws. Secure the
servo tray in place using the mounting screws
provided .
6. Repeat step # 2 - # 5 to install the second aileron
servo in the opposite wing half.
Cut away film only. here
Supplied with the servo
approx. 13mm
2mm
1.5mm
1.5mm
Aileron and Flap Servo
Must be purchased
separately!
Assemble left and right
sides the same way
Cut off shaded portion
2 x 10mm TP Screw
16
< Bottom view >
Aileron
Flap

Tie the string.
Pull out servo cord with string.
Set all scerws securely. If they
come off during flight you will
lose control of your aircraft!
Warning!
TUCANO 60CC
Instruction Manual
3
2x10mm
2x10mm
2x10mm

Pull out servo cord with string.
Cut off shaded portion
Assemble left and right
sides the same way
TUCANO 60CC
Instruction Manual
4
INSTALLING THE AILERONs AND FLAPs LINKAGES
Neutral
Nut
3mm
4
Nylon Nut
3mm
4
Aluminum ball
8
8
4
3 x 25mm Cap Screw
3 x 85mm Push rod
4
4
8
4
4
3 x 12mm Screw
3mm Washer
3x25mm
< Bottom view >
Aileron
Flap
Cut away film only here.

TUCANO 60CC
Instruction Manual
5
Apply threadlocker
(screw cement).
3x12mm
3x12mm
3mm
3mm
Aluminum ball
< Bottom view >
Aileron
Flap
Aileron Rod
Flap Rod

TUCANO 60CC
Instruction Manual
6
INSTALLING THE MAIN LANDING GEAR
4x4mm
12x10mm
6x45mm
6 x 45mm Cap Screw
2
2
2
12x10mm Collar
4x4mm Set Screw
Apply threadlocker
(screw cement).

TUCANO 60CC
Instruction Manual
7
Air Hose
Air Hose
Spring

TUCANO 60CC
Instruction Manual
8
SUPERLOCK AIR RETRACTS
VALVE ONE WAY
7kg /cm2
3 WAY
CONNECTOR
VALVE CONTROL
AIR TANK SERVO
4 WAY CONNECTOR
4 WAY
CONNECTOR
MAIN GEAR
NOSE GEAR
MAIN GEAR
AIR PUMP
AIR SUPPLY
Air Hose Air Hose
Spring

TUCANO 60CC
Instruction Manual
9
< Wheel well >
Apply epoxy glue
Assemble left and right
sides the same way
Pay close attention here!
Cut off shaded portion
1
2