Pickering 40-850 User manual

pickeringtest.com
Issue 5.5 August 2022
40-850/852 User Manual
PXI MEMS Fiber Optic Multiplexer Module

Page (II) MEMS FIBER OPTIC MULTIPLEXER MODULE 40-850/852
pickering
Page (II) REED RELAY MODULE 40-110/115/120/125
pickering
© COPYRIGHT (2022) PICKERING INTERFACES. ALL RIGHTS RESERVED.
No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by
any means without the written permission of Pickering Interfaces.
Technical details contained within this publication are subject to change without notice.
ISO 9001
Reg No. FM38792

Page (III)
MEMS FIBER OPTIC MULTIPLEXER MODULE 40-850/852
pickering
Page (III)
REED RELAY MODULE 40-110/115/120/125
pickering
TECHNICAL SUPPORT
For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.
WARRANTY
All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of
three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be
defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.
Products serviced and repaired outside of the warranty period are warranted for ninety days.
Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.
ENVIRONMENTAL POLICY
Pickering Interfaces operates under an environmental management system similar to ISO 14001.
Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the
environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and
safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can
be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.
Worldwide Technical Support and Product Information
pickeringtest.com
Germany
Tel: [phone]
E-mail: [email protected]
Sweden
Tel: [phone]
E-mail: [email protected]
USA
Tel: (West) [phone]
Tel: (East) [phone]
E-mail: [email protected]
Czech Republic
Tel: [phone]
E-mail: [email protected]
France
Tel [phone]
E-mail [email protected]
Pickering Interfaces Headquarters
Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom
Tel: [phone]
E-Mail: [email protected]
China
Tel: [phone]
E-mail: [email protected]

Page (IV) MEMS FIBER OPTIC MULTIPLEXER MODULE 40-850/852
pickering
Page (IV) REED RELAY MODULE 40-110/115/120/125
pickering
MEANING / DESCRIPTION SYMBOL
PROTECTIVE EARTH (GROUND)
To identify any terminal which is intended for connection to an external conductor for
protection against electric shock in case of a fault, or the terminal of a protective earth
(ground) electrode.
DANGEROUS VOLTAGE
To indicate hazards arising from dangerous voltages.
WARNING / CAUTION
An appropriate safety instruction should be followed or caution to a potential hazard
exists.
Refer to the relevant instructions detailed within the product manual.
HEAVY
If this product is heavy and reference should be made to the safety instructions for
provisions of lifting and moving.
LASER PRODUCT
This product is capable of switching laser optical signals.
STATIC SENSITIVE
To indicate that static sensitive devices are present and handling precautions should
be followed.
!
kg
SAFETY SYMBOLS
PRODUCT SAFETY
The following safety symbols may be used on the product and throughout the product documentation.

Page (V)
MEMS FIBER OPTIC MULTIPLEXER MODULE 40-850/852
pickering
Copyright Statement ...................................................................II
Technical Support and Warranty................................................III
Product Safety .............................................................................IV
Contents (this page)....................................................................V
Warnings and Cautions ..............................................................VII
Section 1
Technical Specication...............................................................1.1
Section 2
Technical Description .................................................................2.1
Functional Description..........................................................2.1
Section 3
Installation....................................................................................3.1
Pre Operation Checks...........................................................3.1
Hardware Installation ............................................................3.2
Software Installation .............................................................3.2
Testing Operation ..................................................................3.3
Section 4
Programming Guide....................................................................4.1
Programming Options For Pickering PXI Modules ............4.1
Module Architecture..............................................................4.2
Programming The Module ....................................................4.3
Section 5
Connector Information................................................................5.1
Section 6
Trouble Shooting .........................................................................6.1
Section 7
Maintenance Information............................................................7.1
Relay Lookup Tables.............................................................7.1
Component Layout................................................................7.2
CONTENTS

Page (VI) MEMS FIBER OPTIC MULTIPLEXER MODULE 40-850/852
pickering
THIS PAGE INTENTIONALLY BLANK

Page (VII)
MEMS FIBER OPTIC MULTIPLEXER MODULE 40-850/852
pickering
Page (VII)
REED RELAY MODULE 40-110/115/120/125
pickering
WARNINGS AND CAUTIONS
WARNING - HAZARDOUS ENVIRONMENTS SYMBOL
This product is not specically designed for use in hazardous environments, for example in explosive
atmospheres. If the product is to be used in hazardous environments we recommend that the user
ensures suitable protective measures are taken.
!
WARNING - DANGER OF ELECTRIC SHOCK SYMBOL
This module may contain hazardous voltages. Before removing the module from the rack remove all
supplies and disconnect user I/O signals.
Unused slots in the PXI/LXI chassis are populated with blanking plates to prevent access to user
I/O signals that may be present. Blanking panels are available to order from Pickering in a variety
of slot widths. If the product is not used in this manner for example by using an extender card then
additional care must be taken to avoid contact with exposed signals.
CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL
Certain semiconductor devices used in this equipment are liable to damage due to static voltage.
Observe the following precautions when handling these devices in their unterminated state, or
sub-assemblies containing these devices:
1. Persons removing sub-assemblies from equipment using these devices must be earthed by a
wrist strap and a resistor at the point provided on the equipment.
2. Soldering irons used during the repair operations must be low voltage types with earthed tips and
isolated from the mains voltage by a double insulated transformer.
3. Outer clothing worn must be unable to generate static charges.
4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in
anti-static bags.
CAUTION - PRODUCT DOCUMENTATION SYMBOL
Suitably qualied & trained users should ensure that the accompanying documentation is fully read
and understood before attempting to install or operate the product.
!
WARNING - RISK OF INJURY SYMBOL
This product may be specically designed to switch optical signals. Under no circumstances look
into the end of an optical output or an optical cable attached to an optical output. LASER RADIATION
CAN SERIOUSLY DAMAGE YOUR EYESIGHT.
Read and understand the safety information of the laser source connected to the optical switch.

Page (VIII) MEMS FIBER OPTIC MULTIPLEXER MODULE 40-850/852
pickering
Page (VIII) REED RELAY MODULE 40-110/115/120/125
pickering
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user
I/O signals (refer to the Maintenance Section).
• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or
the combined weight of the modules & chassis.
• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the
chassis and the user I/O signals.
• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.
• Modules are not accessed to EN 60825, users should observe the safety instructions and laser
class for the 3rd party laser source.
• The module may be capable of switching optical signals from a laser device; do not stare directly
at the user I/O ports.
• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on
the front of the unit.

Page 1.1
MEMS FIBER OPTIC MULTIPLEXER MODULE 40-850/852
pickering SECTION 1 - TECHNICAL SPECIFICATION
SECTION 1 - TECHNICAL SPECIFICATION
PXI MEMS Fiber Optic Multiplexer 40-850/852
pickeringtest.com
ISSUE 8.2 AUG 2022
Ch 1
Ch 2
Ch 3
Ch 4
Com
Ch 5
Ch 6
Ch 7
Ch 8
Com
Ch 1
Ch 2
Ch 3
Ch 4
Block Diagram of
8 Channel Fiber
Optic Multiplexer
Block Diagram of
4 Channel Fiber
Optic Multiplexer
40-852-018
8 Channel Fiber
Optic Multiplexer
ySingle 8 to 1 or Single 4 to 1 Fiber Optic MUX
yHigh Density 1 or 2 Slot Width Modules
yFC/APC, FC/PC or SC/PC Connectors
ySmall Form Factor Connectors LC or MU (mini SC)
y1240 to 1640 nm Single Mode
y700 to 1700 nm Multi-Mode
yReturn Loss >55 dB
yLong Operating Life >109 Operations with High
Repeatability ± 0.01 dB and Good Temperature
Stability
yCrosstalk -60 dB Typical
y1 ms Typical Switching Time
yVISA, IVI & Kernel Drivers Supplied for Windows
ySupported by PXI or LXI Chassis
y3 Year Warranty
Pickering PXI MEMS Fiber Optic multiplexer modules are available
in 8:1 or 4:1 formats with a choice of 5 different connector styles to
suit most applications: FC/APC (for optimal performance), FC/PC
and SC/PC for general applications and LC and MU for high density
applications.
The fiber optic multiplexers connect the common to a channel by
redirecting the optical signal into a selected output fiber. This is
achieved using Micro-Mechanical Mirrors driven by a highly precise
mechanism and activated via an electrical control signal.
The range of MEMS (Micro-Electro-Mechanical-Systems) based
optical switches is:
• 40-850 – Single 4 Channel Multiplexer
• 40-852 – Single 8 Channel Multiplexer
Pickering can construct custom optical systems to customers
precise requirements. We have a large range of electrical switching
modules which can form a complete PXI based telecom switching
solution.
MEMS offers many advantages over traditional optical prism
technology as used in the 40-810/815/820 modules. MEMS offers
similar optical performance but with lower price, higher packing
density, faster operate time and much longer operating life.
Key Features
• Very fast operate time <1 ms
• Very long life >109 operations
• Return loss greater than 55 dB
• High repeatability over a broad range of environmental conditions
• High density
Applications
• Optical signal routing
• Fiber network configuration
• Fiber Optic Component Test

Page 1.2 MEMS FIBER OPTIC MULTIPLEXER MODULE 40-850/852
pickering
SECTION 1 - TECHNICAL SPECIFICATION
MEMS Fiber Optic MUX, 40-850/852
pickeringtest.com
Specifications
Power Requirements
+3.3 V +5 V +12 V -12 V
0 300 mA (typ 220 mA) 0 0
Operating/Storage Conditions
Operating Conditions
Operating Temperature:
Humidity:
Altitude:
0 °C to +55 °C
Up to 90 % non-condensing
5000 m
Storage and Transport Conditions
Storage Temperature:
Humidity:
Altitude:
-20 °C to +75 °C
Up to 90 % non-condensing
15000 m
PXI & CompactPCI Compliance
The module is compliant with the PXI Specification
2.2. Local Bus, Trigger Bus and Star Trigger are not
implemented.
Uses a 33 MHz 32-bit backplane interface.
Safety & CE Compliance
All modules are fully CE compliant and meet applicable
EU directives: Low-voltage safety EN61010-1:2010,
EMC Immunity EN61326-1:2013,
Emissions EN55011:2009+A1:2010.
General Specification (All versions)
Fiber Switch Type:
Internal Fiber Type:
MEMS
SM 9/125
Wavelength:
Insertion loss (4 channel versions):
Insertion loss (8 channel versions):
Return loss (APC version):
Return loss (other versions):
Polarization dependent loss (PDL):
Repeatability:
Crosstalk:
Optical Input Power:
1240 to 1640 nm
1 dB Typ
1.5 dB Typ
60 dB Min
55 dB Min
0.05 dB Max
±0.01 dB Max
-60 dB Max
300 mW Max
Thermal Stability:
(-10 to 75 °C insertion loss variation)
0.2 dB Max
Expected Life: >>109 operations
Maximum Switching Time:
Cycle Rate:
1 ms
500/sec
Additional Specification (MM versions)
Fiber Switch Type:
Internal Fiber Type:
MEMS
MM 62.5/125 or
50/125
Wavelength:
Insertion loss (4 channel versions):
Insertion loss (8 channel versions):
Return loss (other versions):
Polarization dependent loss (PDL):
700 to 1700nm
1 dB Typ
1.5 dB Typ
55 dB Min
0.05 dB Max
Mechanical Characteristics
All modules are either 1 or 2 slot 3U PXI (CompactPCI)
cards as indicated in Product Order Codes.
Module weight: <0.8 Kg typical.
3D models for all versions in a variety of popular file
formats are available on request.
Connectors
PXI bus via 32-bit P1/J1 backplane connector.
Signals via front panel fiber optic connectors (choice of FC/
APC, FC/PC, SC/PC, MU or LC types).
Other Connector Styles
Pickering can manufacture Fiber Optic Switch modules
with other connector styles, please contact sales office for
further information.