Pidion BI-300 Series User manual

BI-300
Barcode configuration
and commands Manual

1. Introduction
This instruction manual is designed to set-up bar code scanner particularly to
optimize the function of BI-300 bar code scanner.
Terminal setting can be done by Pidion Scan Program in connection with
PC/PDA and setting of volume and function of terminal can be done by scanning
bar code.
This manual will instruct the method for BI-300 barcode scanner selection
without using Pidion Scan program
Setting Up
① Scan START bar code.
② Enter into setting mode by sound of operational tone in 1 second interval.
③ Scan the desired SET bar code.
④ Complete by scanning END bar code.
▪ When set-up is succeeded, one beep will sound to confirm
success and
▪ When set-up is failed, lamp on the left will blink with orange
light and will beep twice.
[Setting Up]
Scan START bar code
Scan the desired SET bar code
Scan END bar code
2

※Configuration Set Barcode
Phase Bar Code Remark
START
SET
END
2. Setting up the scan mode of scan button
Scan mode can be set up for scan buttons
① SINGLE: One bar code is scanned for each time scan button is pressed.
② MULTIPLE: Once the scan button is pressed laser emission continues to
and able to read on bar codes consecutively but will not read the same
bar code that has been read once before. Press scan button one more
time to stop laser emission.
③ CONTINUOUS: When scan button is pressed once laser emission
continues and reads on bar codes consecutively. Press scan button one
more time to stop laser emission.
④ TIMEOUT: Time interval for bar code to be read in MULTIPLE/CONTINUOUS mode
can be controlled.
▪ SET POINT VALUE: 0~9999
▪ UNIT: ms (1/1000 of 1 second)
▪ BASIC SET POINT: 2222ms
3

※Configuration Set Barcode
Phase Bar Code Remark
START
SINGLE
MULTIPLE
CONTINUOUS
SET
TIMEOUT
Bar code table
for entering
character
(19-30p)
END
[TIP] Basic modes are marked in bold letters.
4

3. Volume Control
Volume of beep can be set up to 4 phase’s Off/Low/Medium/High.
※Configuration Set Barcode
Phase Bar Code Remark
START
OFF
LOW
MEDIUM
SET
HIGH
END
[TIP] Basic modes are marked in bold letters.
5

6
4. Setting up Time
Time can be set up on terminal. Year, month, day, hour, minute, second and
day of the week is to be set up respectively.
① YEAR: Year can be set up on the terminal.
▪ Standard year is 1900s and enter the desired numbers without
1900.
▪ Only the numbers 70~255 entered otherwise setting will be
cancelled.
▪ (Example) When you enter bar codes in the order of [START],
[YEAR], [1], [0], [9], [END], the year on the terminal will
change to 2009.
② MONTH: Month can be set up on the terminal
▪ Numbers 0~11 represents months 1~12.
Number months
0 January
1 February
2 March
3 April
4 May
5 June
6 July
7 August
8 September
9 October
10 November
11 December
▪ Only the numbers 0~11 to be entered otherwise setting will be
cancelled.
▪ (Example) When you enter bar codes in the order of [START],
[MONTH], [1], [END] month on terminal will change to February.
③ MDAY: Days of the month can be set up on the terminal.
▪ Numbers 1~31 represents days 1~31.
▪ Only the numbers 1~31 to be entered otherwise setting will be
cancelled.
④ HOUR: Hour can be set up on the terminal.

7
▪ Numbers 1~23 represents hours 1~23 and 0 represents 24 hour.
Number Hour Number Hour
1 AM 1:00 13 PM 1:00
2 AM 2:00 14 PM 2:00
3 AM 3:00 15 PM 3:00
4 AM 4:00 16 PM 4:00
5 AM 5:00 17 PM 5:00
6 AM 6:00 18 PM 6:00
7 AM 7:00 19 PM 7:00
8 AM 8:00 20 PM 8:00
9 AM 9:00 21 PM 9:00
10 AM 10:00 22 PM 10:00
11 AM 11:00 23 PM 11:00
12 AM 12:00 0 PM 12:00
▪ Only the numbers 0~23 to be entered otherwise setting will be
cancelled.
⑤ MINUTE: Minute can be set up on the terminal.
▪ Numbers 0~59 represents 0~59 minutes.
▪ Only the numbers 0~59 should be entered otherwise setting will
be cancelled.
⑥ SECOND: Seconds can be set up on the terminal.
▪ Numbers 0~59 represents 0~59 seconds
▪ Only the numbers 0~59 should be entered otherwise setting will
be cancelled.
⑦ WDAY: days of the week can be set up on the terminal.
▪ Numbers 0~6 represent Sunday to Saturday.
Number week
0 Sunday
1 Monday
2 Tuesday
3 Wednesday
4 Thursday
5 Friday
6 Saturday
▪ Only the numbers 0~6 to be entered otherwise setting will be

cancelled.
※Configuration Set Barcode
Phase Bar Code Remark
START
YEAR
MONTH
MDAY
HOUR
MINUTE
SECOND
SET
WDAY
Bar code table
for entering
character
(19-30p)
END
8

5. Prefix/Suffix
In order to allow character to each bar code value, functions can be edited.
① PREFIX: Able to grant characters and symbols in front of bar code value.
▪ (Example) When bar code is entered in the order of [START],
[PREFIX], [A], [B], [END] the characters AB will be placed in
front of each bar code.
※Configuration Set Barcode
Phase Bar Code Remark
START
SET PREFIX
Bar code table
for entering
character
(19-30p)
END
② SUFFIX: Able to grant characters and symbols in the back of bar codes
▪ Basic Set Point: ￦r
※Configuration Set Barcode
Phase Bar Code Remark
START
SET SUFFIX
Bar code table
for entering
character
(19-30p)
END
9

10
6. Setting Up Bar Code Symbol
Bar code symbols can be set up.
Scan ON/OFF bar code after scanning the bar code on bar code symbols.
▪ (Example) To set up and use with UPC-A Leading zero symbol,
enter [START], [UPC-A Leading zero], [ON], [END]
For symbols on bar code below, enter set point after scanning the symbol bar
code.
① Supplementcode
▪ Basic Set Point: 0
Number Description
0 Disable: Will not recognize supplement code
1 Decode: Must recognize Supplementcode in order
to be recognized as correct bar code.
2 Autodiscriminat: With or without the
Supplementcode, will recognize bar code.
▪ Only the numbers 0~2 to be entered otherwise setting will be
cancelled.
② Interleaved 2 of 5 Length Min: Set up minimum cognition length
▪ Basic Set Point: 3
▪ Numbers 0~255 to be entered otherwise setting will be
cancelled.
▪ (Example) In order to set up minimum cognition length of
Interleaved 2 of 5 Length Min to 12, enter [START],
[Interleaved 2 of 5 Length Min], [1], [2], [END]
③ Interleaved 2 of 5 Length Max: Set up Maximum cognition length
▪ Basic Set Point: 30
▪ Enter numbers 0~255 otherwise setting will be cancelled
④ MSI check digit: Set up Check Digit. It is the method to inspect whether
the barcode is correct
▪ Basic Set point: Check_1
▪ Basic Set Point: Check_1