PiiGAB StartKit1 User manual

Manual for PiiGAB Start Kit 1 & 2

2
StartKit1_2.E.1.13
Contents
Introduction .................................................................................................................................................. 3
Difference between StartKit1 and StartKit2 ................................................................................................. 3
Requirments.................................................................................................................................................. 3
Optional requirements.............................................................................................................................. 3
Installation and connections......................................................................................................................... 4
PiiGAB 810’s MAC-address ........................................................................................................................... 5
Find your PiiGAB 810 on your network......................................................................................................... 5
Change IP-address of your PiiGAB 810 gateway........................................................................................... 6
Alter the IP-configuration for your PiiGAB 810......................................................................................... 6
Configure the PiiGAB 810.............................................................................................................................. 8
PiiGAB M-Bus Setup Wizard –M-Bus communication ...............................................................................10
M-Bus communication with RELAY PadPulse M2................................................................................... 11
Change primary address of PadPulse M2 ........................................................................................... 12
Read both primary and secondary address from RELAY PadPulseM2 ............................................... 13
Further RELAY PadPulse M2 configuration......................................................................................... 13
PiiGAB Explorer / M-Bus OPC-server –M-Bus communication.................................................................. 14
Try the StartKit1_2 example project in PiiGAB Explorer......................................................................... 14
RELAY’s PadPulse M2..............................................................................................................................15
Monitor one of the pulse meters........................................................................................................15

3
StartKit1_2.E.1.13
Introduction
This document will describe how to configure PiiGAB Start Kit 1 & 2 with PiiGAB 810 and RELAY PadPulse
M2 communicating over M-Bus.
Difference between StartKit1 and StartKit2
The only difference between StartKit1 and StartKit2 is the M-Bus load configuration of the PiiGAB 810
gateway. The configuration of both StartKits is the same.
StartKit1: PiiGAB 810/5 (five M-Bus loads)
StartKit2: PiiGAB 810/20 (twenty M-Bus loads)
Requirments
One PiiGAB 810 gateway
One RELAY PadPulse M2 gateway
One 24VAC or 24VDC power supply
A local area network (LAN) with DHCP
PiiGAB M-Bus Setup Wizard 3.1.0 or later
PiiGAB Explorer / M-Bus OPC-server
PiiGAB StartKit1_2.zip
Optional requirements
RELAY’s Tools and Docs CD

4
StartKit1_2.E.1.13
Installation and connections
1. Install PiiGAB M-Bus Setup Wizard
2. Install PiiGAB Explorer
3. Extract PiiGAB StartKit1_2.zip to a local folder
4. Connect PiiGAB 810 gateway to the LAN
5. Make sure your computer is connected to the same LAN
6. Connect PiiGAB 810 gateway to a 24V AC or DC power supply
7. Connect PadPulse M2 to the PiiGAB 810 gateway, see picture below
8. Turn the power supply on
9. Wait for PiiGAB 810’s Pwr LED to go steady red

5
StartKit1_2.E.1.13
PiiGAB 810’s MAC-address
On the right gable of the PiiGAB 810 you’ll find a label containing MAC-address of your PiiGAB 810. You
can use these to identify your PiiGAB 810 with PiiGAB M-Bus Setup software.
The MAC-address starts with 00-20-4A or 00-80-A3
Find your PiiGAB 810 on your network
1. Start PiiGAB M-Bus Setup Wizard and go to the main menu
2. Select Find gateways on your network
3. Press Next to continue
4. Your PiiGAB 810 gateway should be listed
5. Find your PiiGAB 810 by the MAC-address column
6. Select your PiiGAB 810 gateway and press Next

6
StartKit1_2.E.1.13
Change IP-address of your PiiGAB 810 gateway
In case you don’t have a network with DHCP you can also address your PiiGAB 810 with a static IP-
address. For this you also need to set your computer to a static IP-address.
Note: For this setup you might need to have a cross-over Ethernet cable between your computer and
the PiiGAB 810 gateway. To be safe you can use a network switch between your computer and your
PiiGAB 810 gateway.
Alter the IP-configuration for your PiiGAB 810
1. Set your computer to a static IP-address
2. Exit and restart PiiGAB M-Bus Setup Wizard and go to the main menu
3. Select Change gateway IP-settings
4. Press Next to continue
5. Select Setup IP using network (UDP broadcast)
6. In the MAC-address field specify the PiiGAB 810 gateway’s MAC-address
7. Press Next to continue

7
StartKit1_2.E.1.13
8. Select Use the following IP-address
9. Specify the IP-configuration you which the PiiGAB 810 gateway should have to match your
computer’s IP-address
10. Press Next to continue
11. Press Apply to set the IP-configuration
12. Wait for the PiiGAB 810 gateway to reboot
13. Press Next to continue
14. Go back to Find your PiiGAB 810 on your network section and see if you can find your PiiGAB 810
gateway with the IP-address you specified

8
StartKit1_2.E.1.13
Configure the PiiGAB 810
This section describes how the PiiGAB 810 should be configured for M-Bus communication.
1. In PiiGAB M-Bus Setup Wizard’s main menu click the Change gateway parameters
2. Press Next to continue
3. Select Connect using network
Note: Make sure the PiiGAB 810 gateway’s IP-address is shown in IP-address/DNS field
4. Press Next to continue

9
StartKit1_2.E.1.13
5. Configure the PiiGAB 810 with these settings
6. Press the Apply button to continue
7. Wait for the program to finish the configuration of the PiiGAB 810 gateway
8. Press Next to continue

10
StartKit1_2.E.1.13
PiiGAB M-Bus Setup Wizard –M-Bus communication
This section will use PiiGAB M-Bus Setup Wizard to verify if the PiiGAB 810 and RELAY PadPulse M2
responses over M-Bus communication.
1. In the main menu select Test, search and configure meters
2. Press Next to continue
3. Select Connect using network and configure the connection as shown in the picture below
Note: Your PiiGAB 810’s IP-address may not be 192.168.10.122. PiiGAB M-Bus Setup Wizard only fill in
the IP-address automatically as you selected in Find your PiiGAB 810 on your network, step 6.
4. Click Next to continue