Pilz PSS u2 ES 16PT 0V User manual

PSS u2 ES 16PT 0V
Operating Manual-1003766-EN-03
}Control system PSS u2
}Remote I/O system PSS u2

Preface
This document is the original document.
Where unavoidable, for reasons of readability, the masculine form has been selected when
formulating this document. We do assure you that all persons are regarded without discrim-
ination and on an equal basis.
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for the user's internal purposes. Suggestions and comments for improving this documenta-
tion will be gratefully received.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,
SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries.
SD means Secure Digital

Contents
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 3
1 Introduction ............................................................................................................................ 4
1.1 Validity of documentation.......................................................................................................... 4
1.2 Using the documentation .......................................................................................................... 4
1.3 Definition of symbols................................................................................................................. 4
2 Overview ................................................................................................................................. 6
2.1 Module features ........................................................................................................................ 6
3 Safety ...................................................................................................................................... 7
3.1 Intended use ............................................................................................................................. 7
3.2 System requirements................................................................................................................ 7
3.3 Safety regulations ..................................................................................................................... 8
3.3.1 Use of qualified personnel ........................................................................................................ 8
3.3.2 Warranty and liability ................................................................................................................ 8
3.3.3 Disposal .................................................................................................................................... 8
4 Function description ............................................................................................................. 9
4.1 Block diagram ........................................................................................................................... 9
4.2 Supply....................................................................................................................................... 9
4.3 Periphery supply ....................................................................................................................... 9
4.4 Energy-saving functions ........................................................................................................... 9
5 Installation .............................................................................................................................. 10
5.1 General installation guidelines.................................................................................................. 10
5.1.1 Dimensions ............................................................................................................................... 10
5.2 Inserting and removing an electronic module ........................................................................... 11
5.2.1 Inserting an electronic module.................................................................................................. 11
5.2.2 Removing an electronic module ............................................................................................... 13
5.2.3 Changing an electronic module during operation ..................................................................... 14
6 Wiring ...................................................................................................................................... 15
6.1 General wiring guidelines ......................................................................................................... 15
6.1.1 Connection mechanism for terminal blocks .............................................................................. 15
6.2 Terminal configuration .............................................................................................................. 16
7 Operation ................................................................................................................................ 17
7.1 Display elements and messages .............................................................................................. 17
8 Technical details .................................................................................................................... 19
9 Order reference ...................................................................................................................... 21
9.1 Product ..................................................................................................................................... 21
9.2 Accessories .............................................................................................................................. 21

Introduction
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 4
1 Introduction
1.1 Validity of documentation
This operating manual explains the function and operation, describes the installation and
provides guidelines on how to connect the product.
This documentation is valid for the product PSS u2 ES 16PT 0V hardware version 01 or
higher. It is valid until new documentation is published.
1.2 Using the documentation
This document is intended for instruction. Only install and commission the product if you
have read and understood this document. The document should be retained for future ref-
erence.
Please refer to the PSS u2 Installation Manual.
1.3 Definition of symbols
Information that is particularly important is identified as follows:
DANGER!
This warning must be heeded! It warns of a hazardous situation that poses
an immediate threat of serious injury and death and indicates preventive
measures that can be taken.
WARNING!
This warning must be heeded! It warns of a hazardous situation that could
lead to serious injury and death and indicates preventive measures that can
be taken.
CAUTION!
This refers to a hazard that can lead to a less serious or minor injury plus
material damage, and also provides information on preventive measures
that can be taken.
NOTICE
This describes a situation in which the product or devices could be dam-
aged and also provides information on preventive measures that can be
taken. It also highlights areas within the text that are of particular import-
ance.

Introduction
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 5
INFORMATION
This gives advice on applications and provides information on special fea-
tures.

Overview
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 6
2 Overview
Module structure:
A module consists of
}an electronic module,
}a terminal block with cage clamp terminals and
}a module carrier
The electronic modules are plugged into the backplane and determine the function. The
backplane is used for communication between the head module and the electronic modules
and forms the carrier unit for the electronic modules. The terminal block is plugged into the
electronic modules and is used to connect the field wiring.
Details of the terminal blocks that can be used are available under "Intended Use".
2.1 Module features
Application of the product PSS u2 ES 16PT 0V:
Electronic module for tapping the periphery supply 0 V
The product has the following features:
}16 terminals for tapping the periphery supply 0 V
}Energy-saving functions
}LEDs for:
– Module error
– Operating status

Safety
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 7
3 Safety
3.1 Intended use
The module may be used for standard applications in a PSS u2 system.
Intended use includes making the electrical installation EMC-compliant. The module is de-
signed for use in an industrial environment. Interference may occur if used in other areas.
The following is deemed improper use in particular
}Any component, technical or electrical modification to the module,
}Use of the module outside the areas described in this manual,
}Any use of the module that is not in accordance with the technical details.
Please also refer to Installation manual PSSu2.
The module PSS u2 ES 16PT 0V may be used in conjunction with the following terminal
block:
}16-pin terminal block
3.2 System requirements
INFORMATION
The module is supported by
}PASconfig from version 1.0.0
– We recommend that you always use the latest version (download
from www.pilz.com).

Safety
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 8
3.3 Safety regulations
3.3.1 Use of qualified personnel
The products may only be assembled, installed, programmed, commissioned, operated,
maintained and decommissioned by persons who are competent to do so.
A competent person is a qualified and knowledgeable person who, because of their train-
ing, experience and current professional activity, has the specialist knowledge required. To
be able to inspect, assess and operate devices, systems and machines, the person has to
be informed of the state of the art and the applicable national, European and international
laws, directives and standards.
It is the company’s responsibility only to employ personnel who
}Are familiar with the basic regulations concerning health and safety / accident prevention,
}Have read and understood the information provided in the section entitled Safety
}Have a good knowledge of the generic and specialist standards applicable to the specific
application.
3.3.2 Warranty and liability
All claims to warranty and liability will be rendered invalid if
}The product was used contrary to the purpose for which it is intended,
}Damage can be attributed to not having followed the guidelines in the manual,
}Operating personnel are not suitably qualified,
}Any type of modification has been made (e.g. exchanging components on the PCB
boards, soldering work etc.).
3.3.3 Disposal
}When decommissioning, please comply with local regulations regarding the disposal of
electronic devices (e.g. Electrical and Electronic Equipment Act).

Function description
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 9
4 Function description
4.1 Block diagram
1
0V
Module
Supply
Data
(ST)
Periphery
Supply
+24 V DC
Module Bus
2
0V
15
0V
16
0V
Periphery
Supply
Periphery
Supply
Fig.: Block diagram PSS u2 ES 16PT 0V
4.2 Supply
}The module is supplied with voltage via the head module.
4.3 Periphery supply
The module provides 16 terminals with the 0V potential of the periphery supply.
4.4 Energy-saving functions
The energy-saving levels are controlled by the head module and are not configurable. The
module supports the following energy-saving levels:
}Switching off the LEDs
– The LED that displays module status is switched off.
}Standby mode
– All module functions are inactive.
– The LEDs that displays module status are switched off.

Installation
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 10
5 Installation
5.1 General installation guidelines
NOTICE
Damage due to electrostatic discharge!
Electrostatic discharge can damage components. Ensure against discharge
before touching the product, e.g. by touching an earthed, conductive sur-
face or by wearing an earthed armband.
5.1.1 Dimensions
The dimensions include the backplane, electronic module and terminal block.
12,5
50,1
54.4
88,37
6
51,1 60
111,1
(95.3)
51,7
Fig.: Dimensions in mm, including backplane, electronic module and terminal block

Installation
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 11
5.2 Inserting and removing an electronic module
Please note:
}Backplane must be installed first.
}Electronic modules may only be plugged or unplugged if the terminal block has been re-
moved first.
}The mechanics of the electronic modules are designed for 20 plug in/out cycles.
5.2.1 Inserting an electronic module
1. Insert the electronic
module into the suspen-
sion lug on the back-
plane.
2. Swivel the electronic
module downwards until
you hear it click into
place.

Installation
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 12
3. Insert the terminal
block into the suspen-
sion lug on the module.
4. Swivel the terminal
block upwards until you
hear it click into place.

Installation
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 13
5.2.2 Removing an electronic module
1. Press the unlocking
mechanism on the ter-
minal block that is
shown by the arrow and
pull off the terminal
block forward.
2. Press the unlocking
mechanism that is
shown by the arrow and
pull off the electronic
module upwards.

Installation
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 14
5.2.3 Changing an electronic module during operation
An electronic module can be hot swapped.
Effects:
}Module bus communication between the other modules is not interrupted.
}The configuration data is retained.
}The module is detected automatically as soon as the module is re-inserted.
Procedure:
1. Removing an electronic module [ 13]
2. Inserting an electronic module [ 11]
A new electronic module can be inserted during operation.
Procedure:
}Inserting an electronic module [ 11]
Effects:
}Module bus communication between the other modules is not interrupted.
}To detect the new module the following steps can be necessary:
– Creating a new configuration or changing an existing configuration
– Download of the configuration to the head module
– Restart of the head module. After a restart, the system behaves as after a warm reset
using a reset pushbutton (see operating manual of the head module, chapter “Reset
pusbutton", section "Carrying out a warm reset (restart)").

Wiring
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 15
6 Wiring
6.1 General wiring guidelines
Please note:
}Signal lines do not have to be shielded.
6.1.1 Connection mechanism for terminal blocks
Procedure:
}Use a flat head screwdriver.
}Strip the wire back 9 mm.
}Feed the stripped cable as far as it will go into the opening for the spring-loaded terminal.
}Check that the cable is firmly seated.
Please note:
}The minimum cable cross section for field connection terminals on the terminal blocks is
0.15mm2 (AWG26).
}The maximum cable cross section for field connection terminals on the terminal blocks is
1.5mm2 with ferrules (AWG14)
}Use copper wiring.

Wiring
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 16
6.2 Terminal configuration
Example for connecting a single-channel actuator in 3-conductor wiring:
Terminal configuration 1-channel actuator
Actuators supplied via the 0V
periphery supply
PSSu2 ES 16DOD
0.5A
1: Output O0
2: Output O1
3: Output O2
4: Output O3
5: Output O4
6: Output O5
7: Output O6
8: Output O7
9: Output O8
10: Output O9
11: Output O10
12: Output O11
13: Output O12
14: Output O13
15: Output O14
16: Output O15
PSSu2 ES 16PT 0V
1: Periphery supply
0V
2: Periphery supply
0V
3: Periphery supply
0V
4: Periphery supply
0V
5: Periphery supply
0V
6: Periphery supply
0V
7: Periphery supply
0V
8: Periphery supply
0V
9: Periphery supply
0V
10: Periphery supply
0V
11: Periphery supply
0V
12: Periphery supply
0V
13: Periphery supply
0V
14: Periphery supply
0V
15: Periphery supply
0V
16: Periphery supply
0V
PSS u2 ES 16PT FE
1: Functional earth
2: Functional earth
3: Functional earth
4: Functional earth
5: Functional earth
6: Functional earth
7: Functional earth
8: Functional earth
9: Functional earth
10: Functional earth
11: Functional earth
12: Functional earth
13: Functional earth
14: Functional earth
15: Functional earth
16: Functional earth
ES 16DOD 0.5A ES 16PT 0V
O0
0V
ES 16PT FE
1616 16

Operation
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 17
7 Operation
The status of the module is displayed via the "Module status" LED; this is signalled to the
head module and any error is entered in the head module's diagnostic log.
7.1 Display elements and messages
[1]
Legend
[1] Module status display

Operation
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 18
The module can detect the following errors:
[1] Colour [1] Meaning Further informa-
tion
-- Module not ready for operation
Green Module ready for operation
Green Module in operation
Red Configuration error
Module was inserted in the wrong slot.
Red Internal errors See module's dia-
gnostic log
Red Temperature error: Too warm (1) See module's dia-
gnostic log
Legend
LED on
LED flashes
LED flashes briefly
LED off
(1) There are two levels of overtemperature.
}Too warm:
If the module temperature exceeds a threshold value, then:
– a warning is sent to the head module.
If the temperature drops back below the threshold value, the module sends an all-clear.
}Too hot:
If the module temperature exceeds another threshold value, then:
– an error message is sent to the head module
After the "too hot" message has been received, if the temperature drops back below the
"too warm" threshold value, the module will switch to an error-free state.

Technical details
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 19
8 Technical details
General
Certifications CE, UKCA, cULus Listed
Application range Standard
Module's device code 0003h
Electrical data
Internal supply voltage (module supply)
Module's power consumption 0,1 W
Environmental data
Climatic suitability EN 60068-2-1, EN 60068-2-14, EN 60068-2-2, EN
60068-2-30, EN 60068-2-78
Ambient temperature
In accordance with the standard EN 60068-2-14
Temperature range 0 - 60 °C
Storage temperature
In accordance with the standard EN 60068-2-1/-2
Temperature range -40 - 70 °C
Climatic suitability
In accordance with the standard EN 60068-2-78
Humidity 93 % r. h. at 40 °C
Condensation during operation Not permitted
Max. operating height above sea level 2000 m
EMC EN 61131-2 (Zone B)
Vibration
In accordance with the standard EN 60068-2-6
Frequency 8,4 - 150 Hz
Acceleration 10 m/s²
Shock stress
In accordance with the standard EN 60068-2-27
Acceleration 150 m/s²
Duration 11 ms
Airgap creepage
In accordance with the standard EN 61131-2, UL/IEC 61010-2-201
Overvoltage category II
Pollution degree 2
Protection type
In accordance with the standard EN 60529
Housing IP20
Mounting area (e.g. control cabinet) IP54
Potential isolation
Potential isolation between Periphery supply and module supply
Type of potential isolation Functional insulation
Rated surge voltage 2500 V

Technical details
Operating Manual PSS u2 ES 16PT 0V
1003766-EN-03 | 20
Mechanical data
Material
Housing PC
Mounting type plug-in
Dimensions
Height 110,8 mm
Width 12,5 mm
Depth 72,5 mm
Weight 29 g
Where standards are undated, the 2015-04 latest editions shall apply.